Se = = WM dll bs Hi Hi 15 William St., New York. YY) v oe oe = Z. O ca e¢ x) Q < Decatur, Il. LE a Vil nngye yy fj LOO, A] 7 Len <2 qs (Ae x= aN eK Z PIE A RS i eA Seaay ? LT =i) aoe CATALOG D Page 2 GUARANTER We guarantee eacn and every Leader Water Supply Sys- tem to be first class and complete, and that it will perfectly and successfully perform the work for which it is designed, and recommen ted by us. and that the tank has been tested to an air pressure of 125 pounds per square inch, and is abso- lutely air tight when it leaves our factory. Should anv tank leak or other part prove defective in material or workman- ship, we agree to repair defect or furnish new part free of charge. PREFACE INCE issuing our first or ‘‘A’’ catalog several years ago, S the business of the Leader Iron Works has experienced an unchecked growth and the Leader system of delivering | | | | water under satisfactory pressure has been developed from | | | a practically unknown theory to a point where the prin- ciple of its operation is now fairly well understood by the general public, and is now recognized by persons of experience fully competent to judge as the most reliable and hygenic method of storing water in large quantities and under sufficient pressure to insure delivery at such velocity as to make it useful and efficient for all domestic purposes, and for fire protection, that has been presented to the notice of the public up to the present time. The development and constantly growing popularity of the pneu- matic system of waterworks is due in no small measure to the efforts and policy of the Leader Jron Works in devoting the energies of men of large experience and recognized ability in this particular line to the designing and perfecting of appliances and complete equipment especially suitable to the duty required, and to the manufacture of its output from the raw material to the finished product ready to install of the very highest quality, both as regards materials and workmanship. The presenting of new designs and improved outfits have neces- sitated issuing catalogs ‘‘B’’ and ‘‘C,” and these also having become inadequate, we are now beginning the distribution of our eata- log C518) 2) \ W« sincerely hope that the results of our efforts in this particular will meet with the same approval by our customers in the way of additional orders as have in the past been accorded the goods of our manufacture, and we take this occasion to thank the many patrons who have so kindly contributed to the progress of our Company, and to solicit a continuance of our pleasant relations. LEADER IRON WORKS. FOR YOUR CONSIDERATION AVING been on the market for the past five years, during which time many thousands of outfits of all sizes have been installed throughout the United States and foreign coun- | || | tries, it would seem superfluous to present an elaborate | | | technical description of the Leader system of water supply, ~ and sinee the success of the system has beyond doubt been demonstrated by actual practice, we have devoted a part of the space in this catalog to presenting the actual commendations of a few of the many satisfied users, and to setting forth our exceptional faeil- ities for designing and furnishing everything that pertains to a ecom- plete and modern system of water distribution under any pressure desired. Starting at about the time that the principle of the hydro- pneumatie system of water supply was first presented, our engineers have been consantly at work designing and improving, and so sim- plifving and perfecting the design of complete equipments, and the details of the various appliances, that we are now able to present to those interested, complete outfits suitable for delivering under ample pressure water drawn from any suitable source of supply, and util- izing such power for pumping the water as may be most desirable or economical, or most readily obtained. We have embodied many of the designs suitable for ordinary conditions of supply, delivery and power in a readily presentable form in the way of standard com- plete outfits, a number of which are illustrated and described herein, and from the various designs submitted an outfit with possibly a few minor modifications can be selected that will fulfill perfectly the requirements of ordinary conditions. However, it is our desire to present to the notice of prospective cus- tomers that it is not necessary to be confined to the selection of an outfit from the pages of our catalog, as our engineers are constantly at work designing outfits to meet special conditions, the require- ments of this service being so varied as to make it impossible to provide the best possible results with standard outfits in all cases. We, therefore, invite your correspondence giving exact conditions as outlined in information blanks, which we gladly furnish, and our engineering department will take pleasure in answering fully, mak- Page 4 ing proper recommendations. We make no charge and consider you under no obligations for this service. In perfecting our engineering organization we have by no means neglected the manufacturing feature of our business, and we have at this time the only factory exclusively engaged in the manufacture of tanks and equipment for hydro-pneumatic waterworks systems, in the country. This means more than might be conveyed by the casual remark for the reason that, having no other line to detract our at- tention, we must devote our entire energy to this business, and our very existence depends upon our suecess in this particular line. For the reasons stated above special attention is constantly given to the production of goods that are suitably designed, built and as- senibled of the very best materials, heavily proportioned, and care- fully inspected, and especially adapted to the work for which they are to be used. The confining of air under pressure is a most exacting service, and it is therefore of the highest importance that every piece of material to be used for this purpose shall be carefully tested and thoroughly inspected before shipping. Our factory is especially equipped for the building of tanks that are perfectly air tight and they are made of heavy material, double riveted and double tested, first with water and afterwards with air at 125 Ibs. pressure and each tank must be made as tight as a pneu- matic tire before it is passed from the testing blocks. Our extended experience in supplying systems to all parts of the world has been the means of calling to our attention that in certain localities the nature of the water is such as to cause a tank to rust rapidly inside, and investigation by our engineering department has in these few cases shown the chemical condition of the water to be of such a nature as to rapidly corrode black steel. To overcome this difficulty and be prepared to furnish tanks to our customers that are surely satisfactory under any and all conditions, we have at great expense provided facilities for galvanizing tanks inside and out, of all sizes up to and including 6 feet in diameter, and any length. We carry at all times a large stock of materials of all kinds, and endeavor to have on hand ready for shipment at any time a few of every size of tank or outfit which we list, and we are, therefore, in position to make prompt shipments at all times. Page 5 qdng ‘NO SNVUd M OL ‘HWOH S\NHUYCTIHO ALNNOO INOWTIUa ‘A[Nd} AIBA SINOZ ‘OUI 0} JoJod NOA 9UO AUB O} JI PUSUTUTODJII PUB SodlaINDUT AUB JAMSUB 0} PRLS AOA 9q [[IM pues ,.2UO JIquINU,, “ee St Jueld anod YUrIYy} I ‘“S}UeUotINbot ano [[B A0J 19]}BM JUSTOIJJNS sn soysluIny pue A10}JOVJSIVSS AJOA ST JIJINO OY} Jey? ABS 07 YSTIM JT Ajdwe s "80. & I yoruw ‘SMUB] “JJ-0%Z AG ‘UI-FG OM} Sutsn ‘waiskSg Jopesy] B&B WOUT 198M YIM por[ddns M ‘OUWOF, S,UsIp[IyO AJUNOD JUOW [eg ey} JO 94NJOId Id9AOD 9}BIvdaS JOpUuN NOA Sutsojoue ul sanseves[d 9yBvi [—uUseWaT}]Ue5 ‘UDIN ‘OTUO ‘BVWUODeY, «LI GNAWWOOAH OL AVT9>», Hen 5 HARTZELL poyerw(Pa Wie Jobnso 3 eeiarrsee Fey Beene id | Petershur< bec J T a ae | Jie 5.Gallup “THE BEST MONEY THAT I EVER SPENT” Gentlemen—The Leader System that I installed is great, and I consider it the best money that I ever spent to secure personal comfort. Would not part with it for any- thing. The system provides hot and cold water throughout the house, and the carrying of water from a well or cis- tern, in a bucket, is a thing of the past, and I can say since I have installed your system I have never heard my wife say, ‘‘Bring me a bucket of water before you go.’’ Now all she has to do is to turn on the faucet. The small amount of labor involved in pumping the water into the tank more than repays you by the con- venience of having water where and when you want it. I would be pleased to answer any inquiries that you care to refer to me, and wishing the Leader success, we remain, Yours very truly, J. H. EAGLESON. “IT KAR EXCELS OUR EXPECTATIONS” Works,—Decatur, III. pneumatic water supply which we have recently installed in our home, Leader Tron Gentlemen— Your system No. 25, is giving entire satisfaction. It sup- plies us with both hot and_ cold water for bath room, kitchen -and, laundry purposes. It far excells our expectations, do not know how we could get along without it. H. C, SCHIFFERLI, Sheridan, N. Y. “SUPPLIES HIS NEIGHBORS” Leader Iron Works, Decatur, III. Gentlemen—I am _ sending you’ under separate cover pictures of our home at McCrory, Ark. The picture of the plant is not very good, but as I have it in a room that is only large enough to protect it, the photographer had to get so close that he could not do it justice. The picture of the dwelling is good, but we could not show any of the waterworks, however, will say that we have the entire house supplied with hot and cold water, and supply a neighbor just across the alley from us as well. Our stock has averaged seven head of cattle and horses and ten hogs all sum- mer, at a cost of not more than 35c per week, and if we had a larger well the eost would bs much less. I am well pleased, only regret that I have been without a system of this kind for so long. Will give you any kind of a recommendation that you want, Yours very truly, W. B. FAKES. Page 8 CY, LY NY Ny % “MONEY COULD NOT OUTFIT” BUY MY Leader Iron Works, Decatur, Ill. Gentlemen—Will say that money could not buy my outfit. The elevated tank in the attic should not be compared with the Leader Water Supply System. It does all you claim for it. I carry about 40 pounds pressure and have pumped the pressure up to 75 pounds by hand with comparative ease. I supply the bath room, kitchen and a sill cock with water, and do not average over five minutes per day, pumping. Yours very truly, ERWIN F. STRAUB, Montandon, Pa. “IT WORKS TO PERFECTION” Gentlemen—The Leader Water Supply System installed in my residence is something I have long wished for but never have had the opportun- ity to avail myself of until I installed your plant. It works to perfection and supplies plenty of water for my use. There have been a number of people in to look at my plant and every one speaks highly of the outfit and the work it performs. I think anyone desiring a system of this kind could do no better than install a Leader System. Yours very truly, W. J. MORGAN, Hyndsville, N. Y. ooo. “WAS SKEPTICAL” Haven. Conn., Jan. 18, 1908. Leader Iron Works, Decatur, Il. Gentlemen—It affords me great pleasure to inform you that the water system which you have installed at my summer home at Woodbridge is all that could be expected. I must confess that before its installation I was somewhat skeptical as to its efficiency, but after a thorough trial covering an entire season, I ascertained that it was all that had been represented, and more. You are at liberty to publish this letter if you wish, and I should be very happy to comunicate with anybody whom you may see fit to refer to me for verification. Yours very truly, JACOB P. GOODH ART. New Page 9 FT KIG. 100-D Figure 100-D illustrates our Leader Water Supply Outfit with Priming Chamber. This outfit has a working capacity of 160 gallons of water, an amount sufficient to supply an ordinary family two days for kitchen and bath room purposes. The pump is especially constructed for this work and has the strength and ease of operation seldom found in an ordinary pump of this type. The outfit is equipped with our Positive Intake Air Valve and Prim- ing Chamber which insures not only the right amount of air, but prevents the pump from losing its priming. The pump is suitable for either well or cistern, but in no case should the level of the water in well or cistern be more than 20-feet below the pump. A complete outfit consists of the following: One 30-inch x 6-foot Leader Tank, total capacity 220 gallons, working ca- pacity 160 gallons. One Fig. 200 Double Acting Horizontal Force Pump with Brass Lined Cyl- inder. One Priming Chamber. One Intake Air Valve. One Pressure Gauge. One Water Gauge. One 1-inch Gate Valve. One 11-inch Swing Check Valve. One #-inch Stop and Waste Cock. One 34-inch Drain Cock. Two Wood Tank Supports, cut to the curvature of the tank. Together with all pipe and fittings, cut and fitted as shown, ready to set up. Larger or smaller tanks may be substituted or galvanized tanks can _ be furnished at difference of price corresponding to regular tank list. Page 10 RIG. 115-D Figure 115-D illustrates our Leader Water Supply outfit suitable for a medium sized residence and as it is compact, requiring little space, it is a very popular outfit, having sufficient capacity for supplying water to kitch- en, laundry and bath room. The pump is especially designed for pumping both air and water but may be used to pump water only, by closing valve on air compressor attachment. This pump will deliver water from a well or cistern that may be located nearby or at a considerable distance, but for good results, the water should be at no greater distance vertically below the pump than 20 ft. We recommend the use of a foot valve on end of suction pipe in well or cistern. The tank has a total capacity of 315 gallons and will deliver about 225 gallons when pumped to 45 lb. pressure. A few minutes pumping each day is sufficient to keep an average family supplied. The complete outfit consists of the following: One 36-inch x 6-foot Leader Tank. One Fig. 205-D Leader Special Air and Water Force Pump. One Water Gauge. One Pressure Gauge. One 1-inch Gate Valve. One 1-inch Check Valve. One 38-inch Stop and Waste Cock. One 43-inch Hose Bibb. Together with all pipe and fittings as shown above. Larger or smaller tanks may be substituted or galvanized tanks can be furnished at difference of price corresponding to regular tank list. Page 11 OPWOWIWBDO00000000000$ FIG, 116-D Figure 116-D illustrates an outfit of practically the same design as Fig. 115-D with the exception that Myers No. 286-A Low Down Pump is substi- tuted for Leader Fig. 205-D; also a smaller tank used. The complete outfit consists of the following: One 30-inch x 6-foot Leader Tank, total capacity 220 gallons; working Cca- pacity 160 gallons. One Myers No. 286-A Low Down Force Pump with air compressor at- tachment. One l-inch Gate Valve. One 1-inch Check Valve. One Water Gauge. One Pressure Gauge. One 3-inch Stop and Waste Cock. One 43-inch Hose Bibb. Together with pipe and fittings as shown above. Larger or smaller tanks may be substituted or galvanized tanks can be furnished at difference of price corresponding to regular tank list. Page 12 oy SSS <= QD,9j0I0 0000000000 | | Z H ¢. V_] SANE I J, | | | | 6A FIG. 117-D Figure 117-D illustrates an outfit similar in size to Fig. 116-D, but with tank placed horizontally and having Fig. 205-D Leader Pump, but a Myers No. 286-A pump can be furnished at same price if wanted. The complete outfit consists of the following: One 30-inch x 8-foot Leader Tank, total capacity 295 gallons; working ca- pacity 200 gallons. One Fig. 205-D Double Acting Force Pump with Brass Lined Cylinder and Air Compressor Attachment. One Water Gauge. One Pressure Gauge. One 1l-inch Gate Valve. One 1-inch Check Valve. One 34-inch Hose Bibb. One #-inch Stop and Waste Cock. Two Wood Supports cut to curvature of the tank. Together with pipe and fittings as shown above. Larger or smaller tanks may be substituted or galvanized tanks can be furnished at difference of price corresponding to regular tank list. Page 13 FIG. 27-D Figure 27-D illustrates a very popular outtit, the tank being equipped with our Improved Automatic Air Valve which is designed to maintain the proper amount of air in the tank at all times by automatically opening and closing a valve supplying air to the pump in accordance with the height of water levei in tank. The pump is also of special design for the duty it performs and is equipped with brass valves throughout. The complete outfit consists of the following: One 30-inch x 8-foot Leader tank, total capacity 295 gallons, working capacity 220 gallons. Onc Leader Improved Automatic Air Valve. One Double Acting Hand Force Pump with brass lined cylinder and brass valves. One Pressure Gauge. One Water Gauge. One 1-inch Angle Valve. One 4-inch Check Valve. One 14-inch Check Valve. One 1-inch Check Valve. One #-inch Stop and Waste Cock. One 34-inch Hose Bibb. Two Wood Supports cut to the curvature of the tank. Together with all pipe and fittings as shown, cut and fitted, ready to set up. Larger or smaller tanks may be substituted or galvanized tanks can be furnished at difference of price corresponding to regular tank list. Page 14 Figure 105-D illustrates our Leader Water Works System as arranged for pumping by hand from shallow well or cistern, but it can, if desired, be operated by wind miill. An outfit of this style is suitable for ordinary family use where water is required for kitchen, laundry, and bathroom purposes. FIG. 105-D The pump is especially constructed for this work and is equipped with our Special Intake Air Valve, also Three Way Valve which can be adjusted to deliver water either to the tank or at the pump as desired. For tubular wells or wells of unusual depth we recommend our Fig. 110-D outfit. The complete outfit consists of the following: One 30-inch x 8-foot Leader Tank, total capacity 295 gallons, working ca- pacity 200 gallons. One Leader Fig. 40-D Force Pump. One 24-inch x 12-inch Brass Lined Cylinder. One Special Intake Air Valve. One Pressure Gauge. One Water Gauge. One i-inch Gate Valve. One 1-inch Swing Check Valve. One %-inch Stop and Waste Cock. One 4$-inch Drain Cock. Two Wood Supports cut to the curvature of the tank. Together with all pipe and fittings as shown, cut and fitted, ready to set up. Larger or smaller tanks may be substituted or galwanized tanks can be furnished at difference of price corresponding to regular tank list. Page 15 VWigure 110-D is intended to be installed with a wind- mill for power, but the pump can also be operated by hand, and is extensively used for water service on farms where in addition to requirements for household supply, many head of stock are to be watered. The liberal tank capacity and regulating cylinder for throwing mill in and out of gear, also pop safety valve for protecting sys- tem from damage by excessive pressures are features which receive the highest commendation from users, while the hydro-pneumatic cylinder insures ample air supply under any condition. The tank may be buried in the ground at well or located where it is protected from frost in basement of house, or other building at a considera- ble distance from well and larger or smaller tanks may be substituted as will best fulfill particular requirements. g4§ | HY DRO-PNEUMATIC | CYLINDER FIG. 110-D it WATER BE GYLINDER E! The complete outfit consists of the following items: One 36-inch x 10-foot Leader Tank, total capacity 525 gallons, working capacity 350 gallons. One Fig. 41-D Force Pump. One 23-inch x 12-inch brass lined water cylinder. One Fig. 55-D 38-inch Hydro-pneumatic cylinder. One Water Gauge. One Pressure Gauge. One 1-inch Gate Valve. One 1-inch Check Valve. One §-inch Stop and Waste Cock. One 34-inch Hose Bibb. Two Wood Supports cut to curvature of tank. Together with pipe and fittings as shown, cut and fitted ready to set up. Larger or smaller tanks may be substituted or galvanized tanks can be furnished at difference of price corresponding to regular tank list. Page 16 FIG. 140-D Figure 140-D illustrates our Leader Water Supply outfit for a medium sized residence provided with pump, driven by gasoline engine, but may also be operated by hand. The equipment of this outfit is exactly the same as Fig. 115-D and in addition is provided a 1 H. P. air-cooled gasoline engine mounted on skids, with gasoline tank, batteries, muffler and everything ready to run, together with a light but powerful geared pump jack and sufficient belting to connect the jack and engine together, thus providing everything that is necessary to make a complete and finished installation. A relief valve is also provided to guard against injury to the plumbing by carelessly allowing an excessive pressure to be pumped up. We recommend the use of a foot valve on the end of suction pipe in well or cistern. The complete out- fit consists of the following items: One 36-inch x 6-foot Leader Tank. One 1 H. P. Air Cooled Gasoline Engine. One Fig. 248-D Leader Pump Jack. One Fig. 205-D Leader Special Air and Water Force Pump. One Water Gauge. ’ One Pressure Gauge. One 1-inch Gate Valve. One 1-inch Check Valve. One 1-inch Relief Valve. One $-inch Stop and Waste Cock. One 43-inch Hose Bibb. Together with all pipe, fittings and belt as shown above. Larger or smaller tanks may be substituted or galvanized tanks can be furnished at difference of price corresponding to regular tank list. Page 17 FIG. 170-D Figure 170-D illustrates a system for supplying both hard and soft water that is deservedly popular in up-to-date country and village homes. Only one pump is required, it being our regular combination air and: water hand pump so connected and arranged with valves that either kind of water may be pumped at will into either tank desired, provided the water in either well or cistern is at no greater vertical depth below pump than 20 feet. A small but powerful air cooled gasoline engine is belted to a light strong geared pump jack and run at such a speed as to deliver about 300 gallons of water per hour. The engine may also be utilized to run a churn, or washing machine, cream separator or other light machinery. The complete outfit consists of the following: Two 86-inch x 6-foot Leader Tanks, total capacity of each 315 gallons; working capacity of each 225 gallons. One Fig. 250-D, 1 H. P. Leader Air Cooled Gasoline Engine. One Leader Fig. 205-D 23-inch x 5-inch Double Acting Force Pump. One Fig. 248-D Leader Pump Jack. Two Water Gauges. Two Pressure Gauges. Two 14-inch Gate Valves. Two 11-inch Gate Valves. One 1-inch Check Valve. One 1l-inch Water Relief Valve. Two #§-inch Stop and Waste Cocks. Two 34-inch Hose Bibbs. Two 14-inch Foot Valves. Together with all pipe, fittings and belt as shown, cut and fitted ready to set up. Larger or smaller tanks may be substituted or galvanized tanks ean be furnished at difference of price corresponding to regular tank list. Page 18 W ‘Th ean Y Lar ee : LY) UM4 LK KAAA sAp_A FIG, 155-D Figure 155-D outfit may be used to advantage where a windmill may or- dinarily be expected to furnish the power to operate it, yet need not be ab- solutely depended upon as the pump is also belted to engine, or may, in case of necessity, be operated by hand. The pump is intended to be used for welis where the water is not more than 20 feet below platform and has a 83-inch x 16-inch seamless brass cylinder securely fastened in the pump stand with the lower end, to which suction pipe connects, terminating about even with base of stand. An air inlet valve is provided and arranged so that air may be supplied to tank as desired. The 13 H. P. air cooled gasoline engine is capable of pumping steadily against a high pressure and being light and compactly mounted on skids with gasoline tank and everything complete it can be readily moved about to be used for numerous other purposes where power is required. The complete outfit consists of the following: One 42-inch x 10-foot Leader Tank, total capacity 720 gallons; working capacity 480 gallons. One 14 H. P., Fig. 250 Air Cooled Gasoline Engine. One Fig. 211-D Combination Pump. One Special Intake Air Valve. One Pressure Gauge. One Water Gauge. One 14-inch Gate Valve. One 14-inch Check Valve. One 1-inch Water Relief Valve. One 3-inch Stop and Waste Cock. One 4-inch Hose Bibb. Two Wood Supports cut to the curvature of the tank. Together with all pipe, fittings and belt as shown, cut and fitted, ready to set up. Larger or smaller tanks may be substituted or galvanized tanks can be furnished at difference of price corresponding to regular tank list. Mm Page 19 Page 20 FIG. 21- Domestic Wa With Power Fo Wig. 21-D shows a systen arranged for hard and soft v is supplied from either a dee is used for laundry, kitchen in the house, and for wate etey OutTor doors, ites sails water lift which supplies sof for kitchen, laundry and means of a smaller pneumat basement. While this syste y complicated, it is in reality positively automatic it requ than the oiling of the windn vided with a hydraulic cylin I\ operation of the mill by th pressure in the hard water Se 4 is so constructed that when t water tank equals the press tank the lift will stop work again until water has been d sure reduced. This will be DK and satisfactory outfit for a homes, or for farmers who farm and wish to enjoy allt ern plumbing in their home is not desirable, the system ' hot air pumping engine or where electricity is availabl We furnish complete drawin: showing the size of pipes, f cessories together with full ing the same with each outfi LEADER HYDRO-PNEUMATIC TANK. LLL Works Pump * modern plumbing r. The hard water r shallow well, and 1 sanitary purposes ‘ stock, sprinkling, sed for operating a ater from a cistern hing purposes by ank located in the 1ay look somewhat ery simple. Being no attention other The pump is pro- which controls the se and fall of the ik. The water lift pressure in the soft in the hard water and will not start n off and the pres- 1d a very complete intry or suburban e a stock or dairy 1dvantages of mod- Where a windmill 1 be operated by a soline engine, and - an electric motor. f the above system igs, valves and ac- lanation for erect- ge oy? Page 21 Mn ———— FIG. 160-D Figure 160-D is very similar in design to Fig. 155-D but the pump is provid- ed with water cylinder so arranged that it may be extended with drop pipe and plunger rods into a deep well and the hydro-pneumatic cylinder connected as shown will provide an ample air supply. The engine is 33 H. P. and may be used for many purposes other than pumping, such as sawing wood, dairying, grinding feed, ete. The engine, water and gasoline tanks, batteries, etc., are all mounted complete on skids and can easily be moved about wherever needed. The complete outfit consists of the following: One 42-inch x 10-foot Leader Tank, total capacity 720 gallons, working ca- pacity 480 gallons. One 34 H. P. Woodpecker Gasoline Engine. One Fig. 44-D Deep Well Working Head, adjustable stroke, 6-inch, 8-inch and 10-inch. One 84-inch Fig. 55-D Hydro-pneumatic Cylinder. One Fig. 71-D 3-inch x 14-inch Water Cylinder. One Water Gauge. One Pressure Gauge. One 14-inch Gate Valve. One 13-inch Check Valve. One 1-inch Water Relief Valve. One 34-inch Hose Bibb. One #-inch Stop and Waste Cock. Two Wood Supports cut to the curvature of the tank. Toe St with all pipe, fittings and belt as shown, cut and fitted read to set up. n Larger or smaller tanks may be substituted or galvanized tanks can be furnished at difference of price corresponding to regular tank list. Page 22 FIG. 145-D Figure 145-D illustrates a compaet and simple outfit in which both the engine and pump are vertical type. The pump has iron outer chamber with brass cylinder and valve suspended therein and the inlet connection for suc- tion pipe is tapped in outer shell at such height as to maintain a water level surrounding the plunger and valve so as to keep them constantly submerged. This pump is furnished in four different sizes giving capacities of 325, 500, 700 and 1000 gallons per hour respectively, and the engine will develop suf- ficient power to operate the largest size. The pump is provided with intake air valve and drain cock. The complete outfit consists of the following: One 36-inch x 10-foot Leader Tank, total capacity 525 gallons, working ca- pacity 350 gallons. One 2 H. P. Leader Gasoline Engine and pumping attachment. One Leader Fig. 218-D Siphon Pump with 24-inch cylinder. One Water Gauge. One Pressure Gauge. One 14-inch Gate Valve. One 14-inch Check Valve. One 1-inch Water Relief Valve. One 4-inch Hose Bibb. One #-inch Stop and Waste Cock. One Special Intake Air Valve. Two Wood Supports cut to the curvature of the tank. Together with all pipe and fittings as shown above. Larger or smaller tanks may be substituted or galvanized tanks can be furnished at difference of price corresponding to regular tank list. —_————— eee Page 23 FIG 150-D Figure 150-D illustrates a system having horizontal power pump, the size shown in cut having a pumping capacity of 720 gallons per hour. Various types of engines are furnished with this outfit, but unless otherwise specified a ra P. engine as shown will be furnished, except that same will be hopper cooled. The pump is made in three other sizes, having capacities of 1300, 2000 and 3000 gallons per hour and an engine of same design of ample power to operate the pump selected is provided. This engine being of the hopper cooled type requires very little water and cannot be injured by freezing. A complete outfit consists of the following: One 42-inch x 14-foot Leader Tank, total capacity 1000 gallons, working capacity 665 gallons. a fone Fig. 48-D Double Acting Force Pump with 38-inch x 5-inch Brass Lined ylinder. One Leader Fig. 254-D 2 H. P. Hopper Cooled Gasoline Engine. One Pressure Gauge. One Water Gauge. One 13-inch Gate Valve. One 13-inch Check Valve. One 11-inch Relief Valve. One 4-inch Hose Bibb. One #-inch Stop and Waste Cock. Two Wood Tank Supports, cut to the curvature of the tank. Together with all pipe, fittings and belt as shown, cut and fitted, ready to set up. Larger or smaller tanks may be substituted or galvanized tanks can be furnished at difference of price corresponding to regular tank list. Cee nee Page 24 I'iG. 180-D Figure 180-D illustrates a very simple and most compact outfit for use where the water may be obtained at a depth of no more than 20 feet below pump and for capacities up to 2000 gallons per hour. The double acting pump cylinder is fastened directly to engine bed and the power of engine is trans- mitted at a reduced speed to the pump by powerful but accurately machined gearing. Water for cooling cylinder is provided from discharge pipe of pump. A convenient and ingenious device provides for throwing the pump out of gear and the engine may be used for power for numerous other purposes by belting from pulley shown in cut, furnished in three sizes having pumping capacities of 1000, 1500 and 2000 gallons per hour with corresponding tank capacities and engine power. The complete outfit as shown consists of the following: One 48-inch x 10-foot Leader Tank, total capacity 1000 gallons, working capacity 665 gallons. One Fig. 60-D Combined Pumping Pngine. One 13-inch Gate Valve. One 1l-inch Relief Valve. One 33-inch Angle Valve. One 14-inch Check Valve. One Water Gauge. One Pressure Gauge. One #-inch Stop and Waste Cock. One 43-inch Hose Bibb. Two Wood Supports cut to curvature of the tank. Together with all pipe and fittings, as shown, cut and fitted ready to set up. Larger or smaller tanks may be substituted or galvanized tanks can be furnished at difference of price corresponding to regular tank list. Page 25 FIG. 165-D Figure 165-D illustrates a water service system capable of pumping from deep well and storing large quantities of water that will fulfill the require- ments of large public or private institutions in isolated locations. The pump is designed strong enough to operate a 4-inch plunger in a well 150 feet deep and will handle from 1200 to 1500 gallons per hour and the en- gine has ample power to operate the pump under full load and may be used for running other machinery. The cylinder when pumping from very deep wells should be placed below the water level in well if possible, therefore with this outfit it is not possible to supply air to the suction pipe as in the smaller outfits and a belted air compressor run from a pulley on a line shaft is a nec- essary part of the equipment. No cylinder or rods are furnished at the price listed as the requirements for these must be determined by information cov- ering the size and depth of well. The complete outfit consists of the following: One 48-inch x 24-foot Leader Tank One 13-inch Water Relief Valve. total capacity 2260 gallons, work- One 43-inch Globe Valve. ing capacity 1500 gallons. One 34-inch Horizontal Check One 4 H. P. Fig. 252-D Leader Gas- Valve. oline Engine (See Special Circular.) One j-inch Angle Valve. One Fig. 221-D Deep Well Work- One #$-inch Stop and Waste Cock. ing Head, 5-inch, 74-inch and 10- One 43-inch Hose Bibb. inch stroke. One piece of shafting, two collars, One Fig. 51-D, 38-inch x 4-inch two drop hangers, three belts and Power Air Compressor. three pulleys. One 2-inch Gate Valve. Together with all pipe and fit- One 2-inech Check Valve. tings, as shown, cut and _ fitted, One Water Gauge. ready to set up. One Pressure Gauge. Wood supports are not furnished with this outfit. We recommend at least two substantial concrete foundations under the tank, also concrete foundation under the engine. Larger or smaller tanks may be substituted or galwanized tanks can be furnished at difference of price corresponding to regular tank list. Page 2f WIG. 175-D Figure 175-D illustrates an outfit in every respect similar to Fig. 165-D except that the motive power is an electric motor instead of a gasoline en- gine. While we list this outfit complete with motor, shafting, pulleys, belting, ete., very frequently the room that may be devoted to the plant is such that the arrangement of shafting, etc., shown in cut will not be suitable and we invite correspondence giving full information as suggested by our information blanks and a sketch showing about the arrangement desired and we will be pleased to submit the recommendations of our engineering department, to- gether with quotations. When an automatic controlling device is used for stopping and starting the motor, which is actuated by the variation of pres- sure in the tank, like shown on page 30, a smaller tank will answer unless the large tank is especially desirable for fire protection. The complete outfit consists of the following: One 48-inch x 24-foot Leader Tank One 2-inch Gate Valve. total capacity 2260 gallons, working One 2-1inch Check Valve. capacity 1500 gallons. One 13-inch Water Relief Valve. One 3 H. P., 60 Cycle, single One 3-ineh Horizontal Check phase, 110 volt, alternating current Valve. ‘ motor. One 34-inch Gate Valve. One Fig. 221-D Deep Well Work- One $-inch Stop and Waste Cock. ing Head, 5-inch, 7k-inch and 10- One piece of shafting. two set inch stroke. collars, two drop hangers, three One Fig. 51-D 3-inch x 4-inch Pow- er Air Compressor. One Water Gauge. One Pressure Gauge. belts and three pulleys. Together with all pipe and fit- tings, as shown, cut and fitted, ready to set up. Larger or smaller tanks may be substituted or galvanized tanks can be furnished at difference of price corresponding to regular tank list. ee ee | Page 27 Ss ee Se SSS See fe x — en —— ‘Ss, SSeS > SSS > ee, E eee 2 =. a \ = = i ae — Ss SS So eS = eS = uy’ 1 iy ILLINOISUSAZ FIG. 185-D Figure 185-D illustrates a Leader Tank supplied with water by a neat and compact electric pumping outfit designed especially to meet the growing de- mand for an inexpensive electrically operated pump. An automatic controller can be furnished with this outfit which will start and stop the motor at de- sired pressure in the tank, at extra cost. This outfit is used often to furnish rain water to city dwellings and to increase the city water pressure in apartment houses. The pumping machin- ery is practically noiseless and this in itself is an attractive feature, espec- ially where it is necessary to have the water system in the basement of the house. These pumps can be furnished in three sizes as follows: 2-inch x 4- inch cylinder, 300 gallons per hour; 23-inch x 4-inch cylinder, 480 gallons per hour; 38-inch x 4-inch cylinder, 720 gallons per hour. Size of motor will in- crease in accordance with capacity of pump. The complete outfit as shown consists of the following: One 30-inch x 8-foot Leader Tank One Water Gauge. total capacity 295 gallons, working One Pressure Gauge. capacity 200 gallons. One #-inch Stop and Waste Cock. One Fig. 224-D Leader direct con- One 44-inch Hose Bibb. nected electric pump, capacity 300 Two Wood Supports cut to the gallons per hour, fitted with 3 H. P. curvature of the tank. motor. Together with all pipe and fit- One 1-inech Gate Valve. tings as shown, cut and _ fitted, One 11-inch Water Relief Valve. ready to set up. One 1-inch Check Valve. Larger or smaller tanks muy be substituted or galvanized tanks can be furnished at difference of price corresponding to regular tank list. Page 28 GER = —. —s SS OIS.USAY wa Meinl KIG. 176-D Figure 176-D_ illustrates a Leader Water Supply System operated by a Triplex Electric Pump, and is suitable for pumping water from wells or cis- terns where the level of the water is not more than 20 feet below the level of the pump. The outfit is especially designed for cities, towns and suburbs where electric power can be procured. Pumps are built in four sizes ranging in capacity from 120 to 600 gallons per hour and can, if desired, be furnished with automatic controller to stop and start the pump by the rise and fall of the pressure, like shown in Fig. 130-D. An outfit of this kind is also suitable for a large residence where water is required for several bath rooms, kitchen, laundry and sprinkling purposes, and consists of the following: One 36-inch x 10-foot Leader Tank, total capacity 525 gallons; working capacity 350 gallons. One No. 11 Triplex Electric Pump for direct current, capacity 120 gallons per hour. One Pressure Gauge. One Water Gauge. One 11-inch Gate Valve. One 11-inch Check Valve. One #-inch Relief Valve. One Intake Air Valve. One 4-inch Hose Bibb. One ¥-inch Stop and Waste Cock. Two Wood Tank Supports, cut to curvature of tank. Together with all pipe and fittings, as shown, cut and fitted ready to set up. Larger or smaller tanks may be substituted or galvanized tanks can be furnished at difference of price corresponding to regular tank list. Ki i... o Page 29 FSIT TBIBF91 OF Surpuodsos109 oid JO voucadjJIP JU poystuany vg uxg syuny, PIY7TUBATEY 10 PoyN|AyVsSGQnsS »g ABW SYuUV], Joppeucy 10 rasa1vy] ‘dn jes 02 Apvoea “OATVA HOOYUD YOUI-[T suo ‘Pete pue yno ‘uMOYS SB sSuljiIy puv odrd [Te yqTA 1941SOL “QATVA 9}B4) YOuUl-T 9uO “Muey 9} JO 9inzJeadino 9s} 01 IND syuoddng poo OMY, “1070UWL “MOOD 2SVAA pue doy yYyout-f sug surddojs puv Suljie4s 10J A9[]]OIJUOD ONeWMIOINY C-8zZZs “Sly 2uO “Aq1lEl VSO YOUT-F 9UQg “10}0U “qd “H | YIM poi ‘ojnurw asd soyouis GE 18 poiesodo ‘OSNVY) OINSSIId 9U() ‘“Inoy dod suol[es gEepF Ajyloedvo ‘duind ojo d-eZZ ‘SI ouo “OSBNBY 19}JB AY VU ‘SUO[I[VS YZ AJlORdRD Surysi0OM OATBA FOTOY JOIBAA YOUI-— vuQ ‘SUO[[VS 09 AjlOvVdBO [B]10O} ‘HUB, 19pVeT JOOJ-ZI X YoUT-9g BUCO :SUIMO[[OJ 91 JO S}SISuUOD UMOYS SB }1IJINO oJ9[dWIOD oY “MUS} OY} UL STAI], 19}BM USATS 7B 10,0 oY} SdoO}S pues sqARIs YOryUM JIJINO SIU} YIM poystuany A[TBVSN ST pod}e1y “SNE SB ToT[O1jU0d OTFeWOINY UY “LIPUTTAD 9Y} MOOG Pe Boo] SABA ATW OHBIUT JopeayT & Jo sueow Aq }IJ}JNO Sty} OF PoT[ddns st aly “LIPUI[AD 19]BM JO OZIS YIM DIUBPAOJDB UL AIBA SIOJOU JO. 9ZIS “BOM SUOT SOANSUL [BIIoJVU PI[OS WoAT JND Suraq SSUIIvIS [[B PUB SUOTUIC OPIUMBI SUIARY PUB SSoTOSTOU A[TBdOI}OBVAd OS[R SI dund stuy “inoy 19d suoles 000'T 02 0G¢Z waoyzy oSuva setjtovdes dunqd ‘“jueforjjo AT9A ST pue JNoYSnNoAYy. pei] sseaq ‘Surmoe orqnop st ‘ST[oM MOT[VYS 10 dep 1sy}Ie UO posn 9q 0] peuUSisep st diuind OU} 7BYy} }dedxX9 G-9)T “SIZ 0} AB[IWIIS JIJINO UV So1BIISNI[! G-OLL INST G-08L SIA Page 30 FIG. 135-D Fig. 135-D illustrates our Leader Water Supply System operated by an Ericsson Hot Air Pumping Engine. This outfit will be readily appreciated by those requiring large quantities of water, and especially by the farmer. The engine meets every demand any pumping engine of equal capacity could supply and does not require the same favorable conditions for successful operation necessary with other kinds of motive power. Water can be pumped from any source, such as wells, cisterns, springs, lakes, rivers and ponds, and will de- liver water to any part of the premises at a pressure from 30 to 50 pounds according to the size of the engine. These engines are equipped with burners for either gas, gasoline, wood or coal, and require very little attention, a few minutes for oiling and starting being all that is necessary. The favorite size for ordinary farm use consists of the following: One 42-inch x 12-foot Leader Tank, total capacity 865 gallons, working capacity 575 gallons. One 8-inch Ericsson Hot Air Pumping Engine. One Pressure Gauge. One Water Gauge. One 1-inch Gate Valve. One 11-inch Swing Check Valve. One i-inch Relief Valve. One Intake Air Valve. One 43-inch Hose Bibb. Two Wood Tank Supports, cut to curvature of tank. Together with all pipe and fittings, as shown, cut and fitted, ready to set up. Larger or smaller tanks may be substituted or galvanized tanks can be furnished at difference of price corresponding to regular tank list. Page 31 Eady EEE SESS iG, 60-D | Engine Speed ene Water : avs Ker it regular 400 Jonnec- ¥ Shipping No Engine Capacity of Pump Vacibiy 0OMAtons ou Pump Speed Weight S ___ to 500 Pump o Tibws He Paalcnrees ; 50 : P1| Air-Cooled |?4, 88's: per 20ur) 400 R. P. M. | 14 inches| Back Gear |600 pounds 4Bore-6 Stroke 150 ft. elevation i “aly SS in 8 rea ew ie ag ZH. P. | 1900 gal } 5 P2 Hopper gals. per 20ur! 400R. P.M. | 1%inches| Back Gear [600 pounds " |4Bore-6 Stroke 150 ft. elevation ‘toon 2 8 al y 2HeP 50 cs ‘ 1500 gals. per hour) ae ; x P3 Regular Pee 400 R. P.M. | l'4ginches|} Back Gear |600 pounds 4 Bore-6 Stroke 150 ft. elevation |e 8tol AVIEls 1B i 50 1800 gals. per hour A : : P4 Hopper : 400 R. P. M. | 2 inches Back Gear |850 pounds 5 Bore-6 Stroke 150 ft. elevation oe Pos a ree BUSA ey 50 2000 gals. per hour : ; Pd Regular _ s 400 R. P.M. | 2inches Back Gear |850 pounds 5 Bore-6 Stroke 150 ft. elevation 8 tol P The Leader Direct Connected Pumping Outfit is used for pumping out of shallow wells, springs or running streams and for forcing water from a lower to a higher floor of city buildings where the water pressure is not sufficient. Engine and Pump are both built on a special base, making a compact and powerful arrangement. By this construction we are enabled to use two fly wheels on engine, which gives a steadier motion and equalizes the strains on the crank shaft bearings. The regular pulley is placed on engine so that engine can be used for ope- rating other machinery. When not desired to pump, it is only necessary to remove one pin to disconnect. The Pump is Brass Lined with Rubber Valves on Brass Valve Seats—can be adjusted for 38-inch, 4-inch or 5-ineh stroke; 5-inch Bore. Page 32 Spee PYRAMID DOUBLE ACTING PISTON PUMP Brass fitted; capacity 720. to 3000 gallons per hour. FIG. 48-D FIG. 230-D FIG, 221-D ; FIG. 240-D Page 33 DOUBLE ACTING LEADER WATER JACKETED AIR COMPRESSOR FORCE PUMP With 24-inch Brass Lined Cylinder and Air Compressor At- tachment. BiG. 51-)D FIG. 205-D HAND AIR PRESSURE PUMP Brass Valves 28x 5 Cylinders THE IMPROVED “TRIUMPH” WATER LIFT SUPPLY CISTERN SUCTION WASTE FIG. 45-B FIG, 52-D i Page 34 Bs’7a10' STROKE. |h CAN BE ATTACHED TO ANY PUMP WITH WINDMILL HEAD. i I i “ili WI HIG. 249-D FIG, 44-D VIG. 41-D Page 35 Gl Ap ~ ADJUSTABLE BASE FIG. 73-D PATENTED FIG. 74-D FIG. 72-D RIG. 75-N Page 37 Capacity of Different Sized Cylinders and Horse Power Required for Different Depths of Wells. V | co) (4, wu wu wo HR Hu wou Hu he 2! oy 7 ~ [St on a) 3) PO give clPOO gi%o ql/?o qlee g|to dls CED w Om « a aH a GH Hp es) aH om rod BE sled bias] OS | Sy Be BSlevss|be8Slbassleasslsassle=s sieel ss Ses meslmes| SE | 85 PESSM ES SMES SR Cee SSS Poe oe ssa lee DRAERA EES SS | ST Foe S/8e 5/2 oo 6/588 5/259 6/9858 She le sas ORO | Bw 1S SSRIS SRS SRS Sa 5 oes oak RES Blo 8 2) Me fe es tet TOPs IY 2 10 6 | 40 | 195] .025 06 09 12 .16 19 ae || Aa 2 12 8 | 40 | 261] .025 06 “09 si) 16 19 yee 2 14 | 10°] 40 | 326] .025 06 09 le 16 19 Onmel Ale 2 16] 12.) 40 | 301) 1085 06 “09 aie 16 19 95 | 114) 1 24] 10 6 | 40 | 247} .025 06 9 lke 16 19 95 | 14/1 oly i 12 8 | 40 | 330; .025 06 09 12 16 19 95 | 114] 1 24; 14 ; 10 | 40 | 413 | .025 06 (9 Ae 16 19 On ealedialen 24/1 16 | 12 | 40 | 496! .025 06 -09 1 16 19 95 | 14/1 245! 10 6 | 40 | 306] .025 06 “09 12 16 19 95 | 114] 1 ane) 8 | 40 | 408] .025 06 09 ll 16 19 95 | 114) 1 246| 14 | 10 | 40 | 510] .025 06 “69 M2 16 19 95 1) 1271 1 EN A || TO | ie Ais 12 19 25 BL 37 5 | Baia 237 | 10 6 | 40 | 370 | 25 06 09 a2 16 19 By) Al il 23, | 12 8 | 40 | 493 | .025 06 09 12 16 19 95 | 114| 1 284 | 14 | 10 | 40 | 617 | .05 12 19 25 81 37 5 14) 1 234 | 16 | 12 | 40 | 740 | .05 12 19 25 BL 37 ie SRA Tl 3 10 6 | 40 | 440 | .025 06 69 aI 16 19 25 | 14! 1% 3 12 Sy) 0 | Se |) as a2 19 25 31 37 5 | 144) 14 3 14 | 10 | 40 | 734] .05 12 19 25 31 37 5 | 14) 1% 3 16 1 40 | 797 | .05 12 19 25 31 37 5 14) 14 By 10 6 | 40 | 517] .05 at 19 25 31 87 ‘5 | 1] 1% 344 | 12 8 | 40 | 690| .05 12 19 25 31 BY 5 | 14) 1% 34] 14 10 40 862 | .075 19 28 37 47 56 15 | Io] 14 344] 16 12 40 | 1085 | .075 19 28 non 47 56 7% =| 1%) 4 344] 10 6 40 577 | .05 ale 19 25 31 By 5 134] 14% Wall athe 8 | 40 | 799 | 075 19 .28 87 47 56 75 | lb! 1% 34] 14 | 10 | 40 | 999] .075 19 28 BT 47 | 5B 1 | 1] 144 3441 16 | 12 | 40 | 1288] .1 25 87 5 625i liee ra mine 144} 144 337 | 10 6 | 40 | 689 | .075 19 28 87 47 56 Ws | Oo) ee BA || ike 8 | 40 | 918! .0% 19 28 87 47 5S 15 \2 | 114 57a el dane OMe sO | aa eat 25 87 5 62 US | |, IBZ 387 | 16 | 19 | 4) | 1878 | 125 31 AY 62 78 194 GN COM Roun iz 4 10 6 | 40 | 783] .0%5 19 .28 87 47 5s iy || Qe 4 12 8 | 40 | 1044] 21 25 37 5 62 ses || Gp De | & 4 14 10 | 40 | 1305 | .125 BL AT 62 #8 94 | 1,60" ale 4 16 | 12 | 40 | 1566 | .125 31 AT 62 78 He i aie || 41441 10 6 | 40 | 991] 07% 19 28 Aye || ee 56 FD We 2YAl 2 414 | 12 8 | 40 | 1321 | .125 81 AT 62 78 94 | 1.09 | ts] 2 44.) 14 | lo | 40 | 1652] .15 BT 56 5 LE ie || aeeil i) e| © 41441} 16 | 12 | 40 | 1982) .175 44 66 87 1.08 1.31 1,530) 234) 25 5 10 6 | 40 | 1224] .125 BL 47 162) 78 94 | 1.09 | 3 | 24 5 12 8 | 40 | 1332 | .125 81 AT 62 78 94 | 1.09 18 | 244 5 14 | 10 | 40 | 2040] .175 44 66 |) AOS ea 1.53 | 3 | 2% 5 1 | Se |) eo eves | 6 5 wey |) il. erase MAY | |) By oe 544 | 10 6 | 40 | 1481 | .125 31 47 .62 18 ES rie) ey ee 51g | 12 8 | 40 | 1947 | .175 44 66 8? 1} 1:08 1:81.) 1. SB alamo 544| 14 | 10 | 40 | 2468] .2 5 Tis We | ORS |) 2, 3 | Oe 514 | 16 | 12 | 40. | 2962) .25 62 Ot | 1.25 | 1.56 |. 1:87 | 29.19 13 | oY 6 10 6 | 40 | 17624 (175 44 66 AS mes. |) gsi I shGe). | 2 z 6 12 8 | 40 | 2450) 2 5 3. it ils ay) 118 2. 4 |4 6 14 | 10 | 40 | 2937 | .25 62 || bese |) nee ey || Bay ila ja 6 16 | 12 | 40 | 3595] 3 7 ||) AUP il 153 Ley |) Oey | By 4 |4 q 10 6 | 40 | 2299] 2 5 ie ik 257i 2. 414] dle i 12 8 | 40 | 2798 | .25 62 94 1 2501-56 a 1e87 yo tO dea lediz 7 14 10 | 40 | 3998 | .375 94 1.4 1.87 | 2.34 | 2.81 | 3.75 | 4%] 434 7 16 12 | 40 | 4798! .45 1.12 1.68. }-92.25 *| 2:81 103.879) 4 baa ee ai, 8 10 6 | 40 | 3133] .3 ft ao | ALIS LR | as | By 6 | 6 8 12 8 | 40 | 4177 |. 375 94 1.4 Tey | OBEN OS | Ge WG |e 8 14 10 | 40 | 5222) .45 1.12 ES Ora OS I GLa is lla LG 8 16 12 | 40 | 6266] .5 15. |) Ue | Ae BRI Bis | i, 6 | 6 The above table is theoretical—to get actual H. P. multiply by 2. The power stated is approximated, as it is impossible to determine exactly the loss of power in friction.. For wells from 150 to 200 feet deep, not over 20 strokes per minute is possible, unless very heavy machinery is used. The capacity given in above table is based on 40 strokes per minute. To find the capacity of any sized cylinder with less than 40 strokes per minute. deduct one-fortieth part of the capacity given for each stroke less than 4¢ strokes per minute. Page 38 Information We Require to Enable Us to Intelligently Specify and Figure on That Which is Best Suited to the Place. 1. What is the source of your water supply? (If a well state size and depth.) 2, Is water within easy suction distance? (Not over 25 feet below pump.) 3. How much water is required per minute or per hour? (Or what do you want to supply?) 4. To what height do you wish to force the water or against what pressure? 5. What is the distance, horizontally, you wish to carry the water by suction and discharge? 6. Do you want a steam pump or a power pump? (Or what kind of power have you?) 7. If for steam state how far boiler will be from pump and what pressure is carried? 8. If gas or gasoline engine state horse power, speed and size of driving pulley. 9. If electric motor state horse power, speed and size of driving pulley. 10. If to pump from deep well, state size of well (inside diam.) total depth and distance down to standing water. 11. If deep well, how far is it down to the rock, or is it made in sand or gravel with screen or strainer at bottom? 12. If you wish us to furnish Electric Motor state whether you have direct or alternating current and what voltage, and if Motor is to be at: tached direct or used with belt? 13. If you wish us to furnish Engine, state if for gas, gasoline or steam, and if you will want us to furnish anything besides Pump. 14. Do you want us to furnish Boiler, and if for Pump only? 15. State for what use pump will be wanted. that is, what kind of factory or plant or building, private or public, ete. Rules for Finding the Size and Speed of Pulleys. To find the size of driving pulleys: Multiply the diameter of the driven by the number of revolutions it shall make and divide the product by the revolu- tions of the driver. The quotient will be the diameter of the driver. The diameter and revolutions of the driver being given to find the dinmeter of the driven that shall make a given number of revolutions: Multiply the diameter of the driver by its number of revolutions and divide the product by the number of revolutions of the driven. The quotient will be the diameter of the driven. Vo find the number of revelutions of the driven pulley: Multiply the diam- eter of the driver by its number of revolutions and divide by the diameter of driven. The quotient will be the number of revolutions of the driven. Page 39 NOTE CAREFUDEY The careful observance of these notes will save many misunderstandings between the purchaser and ourselves. Deliveries subject to car supplies, strikes, accidents and any other causes beyond our control. In making reference to goods, always give the figure, size, number and name of article. Orders from parties unknown to us, or without commercial rating must be accompanied by cash, or satisfactory references. C. O. D. orders must be accompanied by sufficient cash to pay carrier charges both ways. State in your order by which route you wish your goods shipped. Otherwise we wili use our best judgment. Number of pounds pressure at various water levels in a pneumatic tank based on the compression of a single atmosphere: At 5 pounds pressure the tank is 3 full of water. At 10 pounds pressure the tank is 2-5 full of water. At 15 pounds pressure the tank is 3 full of water. At 223 pounds pressure the tank is 3-5 full of water. At 30 pounds pressure the tank is 2-3 full of water. At 35 pounds pressure the tank is 7-10 full of water. At 45 pounds pressure the tank is ? full of water. At 60 pounds pressure the tank is 4-5 full of water. LIST OF CAPACITY AND WEIGHTS OF PNEUMATIC TANKS Size Size Ihe EI =| 20 L As pa B OG As A E 56 24 6 420 140 60 26 7300 3810 24 | 8 541 190 0 28 7800 4100 24 10 629 235 60 30 8300 4390 30 6 565. 220 — 60 32 8700 4680 30 8 713 295 60 34 9200 4970 30 10 825 365 60 36 | 9800 5260 30 12 955 | 440 | 72 20 7400 4250 36 6 696 315 2 22 8000 4670 36 8 880 420 7 24 8500 5090 36 10a RO 12se Sohn 72 26 | 9100 5510 36 12 | 1159 630 79 28 | 9700 5930 42 Seilats70" = 2575 5 ie 30 10200 6350 42 10 | 1584/ 720 | 72 32 10800 6770 > 42 12.2 19897 865 | 72 34 11400 7190 42 14 | 2115 1000 | 72 36 11900 7610 42 16 | 2362] 1150 | 84 20 9200 5780 48 10 | 1861! 1000 | 84 29 9900 6360 48 12 | 2137 1130 ¥ 84 24 10500 6940 48 14 | 2464 | 1300 84 26)4) 0) V1L00 ain 97520 48 16 | 2744 1500 84 28 11800 8100 48 18 | 3751 1700 | 84 30 12400 8680 48 | 20 | 4102 1880 84 32 13200 9260 48 | 24 | 4805 2260 84 34 13800 9840 60 | 20 | 5900 2940 84 | 3614500 10420 60 22 | 6400 3230 | 84 40 | 15800 | 11580 60 24 | 6900 | 3520 | 96 36 18000 13500