/>£?/*• S\\ea/*w • la Digitized by the Internet Archive in 2015 https://archive.org/details/pricesofcabinetw01unse PRICES OF CABINET WORK, WITH TABLES AND DESIGNS, ILLUSTRATING THE VARIOUS ARTICLES OF MANUFACTURE, REVISED AND CORRECTED BY A COMMITTEE OF MASTERS CABINET MAKERS. London : PRINTED BY S. LOW, BERWICK STREET, SOHO ; AND SOLD BY MESSRS. TAYLORS, AT THEIR ARCHITECTURAL LIBRARY, HIGH HOLBORN J AND E. BOOKER, NEW BOND STREET. * . % ' « PREFACE. The Utility of a general Standard, whereby to ascer- tain the Prices of Piece Work in the Cabinet Bufmefs, and the great Inconveniences necelfarily refulting from the Want of it, have been long acknowledged, and are indeed too obvious to require a Comment. It may appear difficult, perhaps nearly impracticable, to eftimate the Prices to Articles which the caprice of Fafhion is conftantly varying. As accurate a Mode of Calculation as the Nature of the Cafe would admit of hath been adopted, and it is conceived that few Changes are likely to take place to which the Calcula- tions in this Work may not be found applicable. a 2 In ( iv ) In forming the different Defigns, illuflrating the va- rious Articles of Manufadlure, Attention hath been paid rather to Utility than Ornament. Outlines there- fore are only given, which, it is prefumed, will he found fully fufficient to give an adequate Idea of the Work. The advanced Price of every neceffary of Life re- quired an Increafe to the Wages of the induftrious Mechanic; to this it is truffed the Work will fhew that due Regard hath been paid, and the mutual Interefl of the Mailer and Journeyman properly confulted. Confcious of the Necelfity of a proper Regulation, the Mahers Cabinet Makers of London have applied themfelves attentively to the Compilation of the pre- fent Work, which they truft will be of general Ser- vice to the Trade, and which is the utmoff Objedt of their Wifhes. GENERAL ( V ) GENERAL OBSERVATIONS, &c. All Drawer Work, &c. in tingle earcafes, to meafure on the car- cafe ; and all work with double earcafes to meafure the bottom one. A Bookcafe, when made to rtand on a Secretary, &c. to meafure only its own length ; Libraries, on the bottom carcafe. All Table Work to meafure on the tops, and to fhart with plain Marlbro’ legs without caflors, except otherwife mentioned in the preamble. The Nuts of Handles to be let in except on fham drawers. The Plates of Locks to be let in, except on Chamber tables, Bureaus, Wardrobes, Double cherts, Lobby and Drerting cherts, with rtraight fronts. When a Secretary Drawer is introduced into any piece of work, de- duct the price of the drawers taken out tor its reception, then add the price of the fecretary drawer. All Drawer Work to rtart with plain backs, except otherwife men- tioned in the preamble. Lipping ( vi ) Lipping table tops for cloth, to ftand againft cleaning up. If the edges of tops are veneer’d long-way, dedud from the hart of veneer’d edges, per foot — - — When the edges of tables, &c. are veneer’d, or lip’d for cloth, with king, tulip, or any other hard wood, crofs- way, to be extra per foot from mahogany, except the piece of work is made of the fame — — — If aftragal edges of tables have but one fquare, dedud from the hart of aftragal edges, per foot — — — Working mouldings under the tops of pier tables to be the fame price as thofe in ftdeboards. If the ends of a Secretary exceed two feet wide, when book fhelves at bottom, each extra inch - — — Ditto when clothes-prefs fhelves or drawers — — — When the partitions in the infide of a fecretary drawer are made to Aide in miter grooves, each groove extra — Ditto the upright partitions in counting-houfe bookcafe, each groove _______ Colouring and polithing drawer bottoms, each - — Lining drawer bottoms with paper, each — - — Havannah cedar clothes lhelves or drawers, to be extra from wainfcot or mahogany, each - — _ _ When the ends of eliptic drawer fronts are made quick, and halved on to the middle part, each drawer extra - Veneering ditto, each long drawer — _ _ _ Ditto each fhort ditto — — — When an inclofed pier table is put together as a carcafe, on ftump feet inftead of being fram’d into the legs, de- dud: for each leg - — — Flufh beads on drawers of black, white, or fatin wood, to be the fame as mahogany cock beads. £■ O o o o o o o o o o o o o 0 s. d . o o o£ O 2 ° 3 O c4 o o o 1 1 o 6 0 6 1 2 0 7 1 6 French to|~ ( vii ) ]T . s, d» French feet when Jo lid, to be extra from bafe and brackets on ftraight work — — — — — — oio A cornice frame, made to take to pieces for packing, for bookcafes, &c. extra — — — — — — oio Ditto for a library, &c. — — — — — — 020 Common and miter clamping, when morticed, to be double the price of clamping with a groove. Polifhing the outlide of any work with hard zuax, to be double the price of oil polifhing. Ditto with turpentine and wax to be the fame price as oil polifhing. Moulds and cauls to be provided for the workman, or paid for according to time. All work, either folid, or veneer’d with Satin wood, to be extra in the pound from mahogany, calculated with all the work on it, except banding and bringing — —026 Wainfcot or Deal work, to be in the pound lefs than ma- hogany - - - - - - - -026 The joints in ditto to be paid for the fame as mahogany. Work made for japanning of foft mahogany, to be the fame as wainfcot. ERRATA, ( viii ) ERRATA. e 1 Line 20 tor of Slider read or Slider. - 3 16 omit the word top. 5 10 omit the word top. 9 2 3 for 170 read x 8 0 - 10 10 for 003 read 004 ~ 15 21 tor under the top read above the baje moulding. 9 tor under the top read above the baje moulding. - 3 6 2 5 read with frames for the Cornice and Brackets. - 38 7 for The grooves read T grooves. - 4 1 1 for 004 read 003 - 4 2 12 for width of ends 003 read width of ends - 43 17 for plate 7 read plate 2. - 43 - 18 for plate 7 read plate 2. - 44 ' 6 for depth 003 read depth 002 * 47 ' 1 1 for plate 1 read plate 2. ■ 48 • 1 for height read width. • 5 2 ■ 6 for 2 xx 0 read 2 xo 0 ■ 55 ■ 4 after veneer d crofs-way read with one corner Jh ■ 60 - 27 for plate 13 read plate 14. • 7 6 ' 21 for 030 read 026 85- 16 for three feet four read three feet three. 88 - 6 for 020 read 016 — . 29 for fix'd to the legs read fitted to the legs. 123 - 8 for x 18 6 read x ig 6 138 - 21 for 2 xo 0 read 2 X2 0 i 45 - 26 for 002 read 0 0 1^ 146 - 1 for 0 0 2i read 0 02 147 - x 1 for 0 0 2| read 0 02 *49 - 2 3 for 002 read 0 0 x| — 2 4 for 0 0 2| read 0 02 151 - 6 for 0 0 2| read 002 l 5 2 - *3 for 0 0 2| read 002 164 - 2 3 for 0 03 read 0 02 l86 - J 9 for 070 read 0 60 236 - 7 for three feet four read three feet three. 246 - 12 for width read height. Table No. XI. line 23, for each extra firing read a firing on the upperfi.de of the fafcia. INDEX. ( ix ) INDEX. B. Bason stand Ditto, inclofed — — — - Bureau — — — — - Bureau Bedftead - — Bookcafe - — — - Book Shelves — — — - Book Stands - - - - Biddets — — — — - Bottle Tray — - - - Bottle or Liquor Cafe - - Bottle Cafe (Folding) — Bottle Carriers — — — Butler’s Tray - — — Box — — — — Banding - — - - Brafs Work - — - - Bed Table — - — Bed Steps - — — C. Clothes Prefs — — - Low Ditto - - - b Page - 164 - - - 165 26 - - - 40 “ 42 251 - - 240 to 243 - - 185 and 186 - - - 212 230 258 - - 212 and 213 - - - 218 230 Tables, No. 1 and 2 - Table, No. 16 “ 252 - - - ibid. 3i 3 ° Clothes Page Clothes Prefs, Round Front — — — - 33 Clothes Prefs, with Wings - — — — — 34 Counting-houfe Bookcafe - — — — — 44 Ditto Defks - - — - — - - 189 to 193 Cabinet — - — — - — — — 5 ° Ditto Ladies — — — — - — — — 81 Cylinder-fall Writing Table - — — — 5 2 Ditto Defk — — — — — - - 54 Ditto Wafh-hand Tables - - — — — 174 and 176 Card Table, Square - - - — — - 9 1 Ditto, Circular — - — — - - — 93 Ditto, with Canted Corners — — — — — 94 Ditto, with Round Corners - — - - — - ibid. Ditto, with Quarter-round Corners - - — 95 Ditto, with Ovalo Corners - — - — — 96 Chamber Table — — — — - - 98 Corner Bafon Stand — — — - - - - 1 66 Ditto, inclofed — — - - — — - 168 Cellerets — — — — - - — - 202 to 2.10 Cittern, Oval — — — — — — — - 210 Chamber Horfe — — — - - - 215 Clothes Horfes — - — — - — - 21 6 and 217 Coffee-Room Table — — - - — — - 220 Candle Stand — — . - — — — — - 228 Claws — — — - — — • - Table, No. 4 Chifonieres - — — — — — — 240 and 241 Canterbury - — — — - - - 245 Carcale (Open) - D 246 Dining Tables — — — - — — — 145 and 146 Ditto, Horfe-fhoe “ - 148 Dining ( X1 ) Page Dining Tables on Pillar and Claws - - - - 149 D reding Ched — — — — — — — — l Ditto, Round Front ------- 3 Ditto, Serpentine _______ 5 Ditto, Serpentine, with Straight Wings — — — — 7 Ditto, Serpentine, with Ogee Ends _ — _ - 8 Ditto, French Commode ______ 9 Dreding Ched, with Knee-hole _____ ibid. Ditto, with Round Front — — — — — — n Ditto, Serpentine _______ 12 Double Ched of Drawers — — — — — — 28 Ditto, Round Front - - _ , _ _ - — 29 Drawers to dand on Counting-houfe Delks - - 195 and 196 Difpenfaries - _____ _ 253 to 257 Doors for Recedes, &c. _ _ _ _ Table, No. 12 Doors, Oval ______ Table, No. 14 Door, Glazed — - .— - - — Table, No. 15 Didedion of a Knife-cafe ______ 233 Dumb Waiter ________ 235 F. French Commode Dreding Ched _____ g Furniture Drawer _______ 18 Flaps _________ 1 47 Fire Screen, Horfe _______ 222 Ditto, Folding — _ — 223 Ditto, Sliding — — — — - — — — — 224 Ditto, Pole _______ 225 to 228 Flower Stand ________ 228 Fluting _______ Table, No. 1 1 b 2 Gentleman’s ( xii ) g. V 7 . Page Gentleman’s Drefling Table - — - - — — J 57 Gentleman’s Drefling Stand - — — — — - 160 Gout Stool - — — — - — — — 2 45 H. Horfe-fhoe Dining Table - — — — — - 148 Harlequin Table - - — — — — 2 37 I. Inclofures for Counting-Houfe Defks _ . - 196 Inlaying Claws — — - — — Table, No. 5 Inlaying Tripod Standards - — — — Table, No. 5 K. Knee-hole Drefling Chefl — — - - — — 9 Ditto, Round Front — — — — — — — 1 1 Ditto, Serpentine — — — — — - — 12 Kidney Library Writing Table - — — — — 69 Ditto, with Knee-hole — — — — — — — 71 Knife Tray - — — — — — — — 218 Knife Cafe _____ _ — — 232 Vafe Ditto _ — — — - — — — 2 34 L. Lobby Chefl — — - — — — — — 3 3 Ditto, Round Front — - — — — — — 15 Ditto, Serpentine _ - - — — — — 16 Library Bookcafe _ — — — — _ — 45 Ditto, with Breaks - - - — — — — 47 Library ( xi >i ) Library Writing Table — — — — Page 6l Ditto, with Knee-hole — — — — — — — ,63 Ditto, with Tambour Top — — — - — — 57 Ditto, Serpentine — - — — — — — 66 Ditto, Circular — — 67 Loo Table — - — — — — — — 150 Lady’s Drefling Tables — — - — — >53 to >57 Lady’s Drefling Stand — — — — — — 158 Liquor Cafe — — 230 Mufic Stand - — M. 00 ►H Mufic Stool — — 244 Mouldings — — - — — — Table, No. 1 1 Moulding Legs — — — — — — Table, No. 7 Moulding Tripod Standards - — - — Table, No. 6 Moving Libraries — — - — — — 240 and 241 Moving Book Stand — - - — - - - 243 Medicine Cheft - - 257 Night Stool — - N. 180 Night Tables - - - — - - - 18 1 to 184 Prefs Bedftead — - P. 36 Ditto, with Breaks - — — — - — — 4 1 Pembroke Table - — — — — — — 8 5 Ditto, on Claws - - 236 Ditto, with Sliding Flaps — - — — — 89 Pier Tables — — — — — — — 101 to I IS Pedeftal — - — 14 1 Pillar ( xiv ) Pillar and Claw Table Pot Cupboard — Ditto for a Corner Plate Carrier - Pail Pediments — Pole Screens — Plinthing Legs — Pannelling — Portable Writing Defk Quartering Pannels Page 1 5 1 I 77 ------ 1 79 ------ 235 - - - - - - 21 1 ------ 221 ------ 225 to 228 - — - — Table, No. 3 - Tables, No. 5, 6 , 7, 8, g, 10 ------ 247 Table, No. 6 R. Round-front DrelTing Cheft - — - Ditto, with Knee-hole — — — — Ditto Lobby Cheft — - — - Ditto Secretary — - - - - Rifing-top Writing Table - — — Rudd Table — — — — — Rudd Drefling Cheft — — - — Reading Stand — - — — - Reeds for Tambour Tables — - - Reeding Legs, &c. — — - - Reeding Pilafters, &c. - — - Recedes, filling up — — — - S. Serpentine Drefiing Cheft - — - Ditto, with Straight Wings — - Ditto, with Ogee Ends — — Ditto, with Knee-hole — — - - " 3 - - 11 “ " 13 24 75 - - 161 163 187 Table, No. 10 Table, No. 7 Table, No. 7 Table, No. 14 5 7 8 - 1 2 Serpentine ( xv ) Serpentine Lobby Cheft Secretary - — — Ditto, with Round Front Ditto, Serpentine — Secretary Drawer — Screen Writing Table Social Table — — Sideboards - — Slab Ditto — Shaving Stands — — Screen Dreffing Glafs - Sham Drawer Fronts Table Bedfteads — Tambour Writing Table Ditto, No. 2. - — Ditto Defk — — Tops for Tambour Tables Table Delks - — Tea Trays — — Tripod Stands — — Tripod Standards — Therming Legs - — Tea Chefts — — U. and V. Univerfal Table — — — Vafes — — — — — Vafe Knife Cafes — - — Urn Stands — — — — Voider — — — - — Voider Stand - — — - Page 16 - - 22 24 25 - - 20 77 97 - 116 to 140 - 148 - 168 to 173 - - 229 Table, No. 10 “ - 38 55 56 57 59 188 - 214 and 215 - - 228 Table, No. 5 Table, No. 3 - 249 and 250 " - 89 : 44 234 - 1 99 to 201 - - 218 - - 220 Veneering ( xv * ) Veneering Cylinder Falls - Veneering Legs, &c. — - Veneering Doors - - W. Writing Table, as in Plate 4. Ditto, as in Plate 6. — — - Writing Screen, Ladies — Ditto, Gentleman’s - - Work Table, Square — - Ditto, Oval - - - Ditto, with Canted Corners Ditto, as in Plate 7, fig. 2. Work Stand - - - Window Blind - - - Page Table, No. 6 Table, No. 7 Table, No. 13 73 “ 74 - - - 78 79 - - - 197 198 239 - - - 83 “ “ - I 5 2 - - - 217 THE THE CABINET-MAKERS’ Eonfcon BOOK OF PRICES. A DRESSING CHEST, T„ ree feet long, four drawers in ditto, cock beaded, £. s. d. aflragal or flone moulding on the edge of the top, or the edge veneer’d, and a firing in the upper comer, fail plinth, or common brackets — - — — — 0160 EXTRAS. Each inch, more or lefs, in length, down to 2 feet 6 inches 006 Ditto, above 2 feet 8 inches high - - - -003 Each drawer, more or lefs — - — - - 023 Slipping drawer fides, and plowing bottoms in, each drawer - - - - - - - -003 Munting in each bottom - - - - - — 003 Half ditto under the bottom - - - - -OO iv Each partition, more or lefs - - - - -006 Lining each ditto - - - - - - -001 A front edge under the top of flider, or above the bafe moulding - - _ — _ _ —003 b A frieze [ 2 ] A frieze under the top moulding veneer’d crofs-way, with aftragal at foot — Glueing up ends, top, or drawer fronts, either folid or to veneer on, at per joint — — — — — — Clamping the top end-way, to appear as folid - - Veneering the top - — — — - — — Each joint in the veneer - — Veneering each end - — — - — - — Each joint in the veneer — Veneering long drawer fronts, each _ — — — Ditto fhort drawer fronts, each Each butt joint in the veneer — — — — — Veneering partition edges alkew or crofs-way, per foot extra Ditto with king, tulip, or any other hard wood, at per foot extra - — — — — — Veneering the plinth ftraight-way — Ditto crofs-way, Each joint extra - - - - Blocking the brackets with inch ftuff crofs’d - — A loofe feme for plinth or brackets — - - French feet, or folid French brackets — — — — Veneering ditto, each fide — - — — — Ditto common brackets, each fide - — - — A bead round the bottom of carcafe or bafe moulding — An aftragal ditto - — - — — — — A ftider fquare clamp’d, folid or lip’d for cloth, cock beaded Miter clamping ditto, each miter extra — - - A ftider ivith one pannel, lip’d for cloth — - - Lining the ftider with cloth - - - - — Fram’d back, each pannel — — — — — A munting in plain back - — — - — — When made with three drawers, each inch in the drawers aboVe eight inches deep — — — — — £■ s. d. O 1 6 O o 1 o o 6 o 1 o o o 6 o 1 o o o 3 o o 6 o o 4 o o 4 o o °t o o i o o 8 o o i o o 4 o 1 o o 2 o o o 2 o 0 it o o 9 o 1 o o 1 6 o o 6 o 2 o o o 6 o o 6 o o 3 o o 2 Lining i 3 J Lining up ends to form pilafters, and veneering ditto, or putting on quarter fluff - - . — - - - Stump feet the lame as common brackets. Oiling and polifhing ------ £■ O o s. d. 2 6 o 6 C >0*2*0 A ROUND-FRONT DRESSING CHEST, Three feet long, four drawers in ditto, cock beaded, aftragal cr flone moulding on the edge of the top, or the edge veneer’d, and a firing in the upper corner, French feet, or common brackets — — — - - — 150 EXTRAS. Each inch, more or lefs, in length - - — - Ditto, above 2 feet 8 inches high - — — - Eliptic fweep, extra from round front — — — — Each drawer, more or lefs — — — — — Each partition, more or lefs — — — — — A front edge under the top or flider — — — - Lining each partition crofs-way — — - — Slipping drawer fides , and plowing bottoms in, each drawer Munting in each bottom ______ Half ditto under the bottom - - - — _ A frieze under the top moulding veneer’d crofs-way, with an aflragal at foot ______ Glueing up ends or top, either folid or to veneer on, at per joint ________ Sawing drawer fronts out of two-inch fluff, each cut — Ditto three inch _______ Glueing up ditto, each joint _ _ _ _ _ Clamping the top end-way, to appear as folid - - b 2 00 6 003 020 030 008 004 O Ox 003 003 0014- 0 1 9 001 o o r o o ljr 0 0 2 0 0 6 Veneering C 4 ] Veneering the top — — — - — Each joint in the veneer - — — - — — Veneering each end ______ Each joint in the veneer - — - — — — Veneering drawer fronts outfide, each _ - — Ditto infide — — — — — Each butt joint in the veneer _ _ - — — If crofs-way, each joint — Veneering partition edges afkew or crofs-way, extra from flraight per foot — — — — — — — Ditto with king, tulip, or any other hard wood — — Blocking the brackets with inch fluff crofs’d - - Solid French brackets ____ — - Veneering each fide of ditto _ — — — — Ditto common ditto ______ A bead round the bottom of the carcafe or bafe moulding An aflragal ditto — — — — — — — A loofe frame for French or common brackets — - A flider fquare clamp’d, folid or lip’d for cloth, cock beaded Miter clamping ditto, each miter extra - — — A flider with one pannel, lip’d for cloth — — — Each extra pannel — — — — — — — Veneering a plain flider — — — — — — Lining the flider with cloth — _ — — — Fram’d back, each pannel — — — — — A munting in plain back ------ When made with three drawers, each inch in the drawers above eight inches deep _____ Lining up ends to form pilaffers, and putting on quarter fluff, or veneering ditto _ _ — — _ Stump feet the fame price as common brackets. Oiling and polilhiiig ______ £. s. d. O 1 o 006 010 003 0010 006 006 0 0 2 0 o o\ 001 004 0 2 0 0 0 2 O O \\ 009 o 1 o 010 0 2 0 0 0 6 0 2 6 00 6 008 006 006 003 002^- 040 008 A SER- [ 5 ] ' A SERPENTINE DRESSING CHEST, Three feet long, four drawers in ditto, cock beaded, £. s. d. aflragal or flone moulding on the edge of the top, or the edge veneer’d, and a firing in the upper corner, French feet, or common brackets — — — — 1140 EXTRAS. Each inch, more or lefs, in length — — — — o Ditto, above 2 feet 8 inches high — — — - o Each drawer, more or lefs — - — - — o A front edge under the top or flider — — — — o Each partition, more or lefs — — — — — o Lining each ditto crofs-way — — — — — o Slipping drawer fides, and plowing bottoms in, each drawer o Munting in each drawer — — — — — — o Half ditto under the bottom — — — — — o A frieze under the top moulding veneer’d crofs-way, with an aftragal at foot — — — — — — o Glueing up ends or top, either folid or to veneer on, at per joint — — — — — — — — o Sawing drawer fronts out of two-inch fluff, each cut — o Ditto three inch - - — — - — — o Glueing up ditto, each joint — — — — - o Clamping the top end- way, to appear as folid — - o Veneering the top — — — — — — — o Each joint in the veneer — — — — — — o Veneering each end — — — — — — o Each joint in the veneer — — — — — — o Veneering drawer fronts outfide, each - - - o Ditto infide - - — — — — __ 0 1 o ° 3 3 9 o 4 0 9 o 1 0 3 o 3 O ljr 2 O O 1 O 1 O It O 2 0 6 1 o 0 6 1 o 0 3 1 o 0 7 Each [ 6 ] £■ s. d. Each butt joint in the veneer — - - — - O o 6 If crofs-way, each joint — — — — - — O o 2 When but three drawers in height, for veneering each front outfide — — — — — — - — o 1 1 Ditto infide — — — — — — — — o o 8 Veneering partition edges afkew or crofs-way, at per foot extra from ftraight — — — — - — o o Ditto with king, tulip, or any other hard wood — - o o 1 Blocking the brackets with inch fluff crofs’d — — o o 4 Solid French brackets - - - — — — o 2 o Veneering each fide of ditto — — — - o o 2 Crofs banding French feet or any other part — See Table of Banding. A loofe frame for French or common brackets — — o 1 o A bead round the bottom of the carcafe or bafe moulding o o io An aftragal ditto - — — — — — — o 1 2 Canted corners with ends lin’d up - — — — o 3 o If continued through the top moulding and brackets — o 4 o Sweeping the ends of top half ferpentine, when the ends are ftraight — — — — — — — o 1 o For fetting the ends bevelling — — — - — o 2 6 Hollow ends at the front edges - — — — — o 4 6 Sweeping the ends and top half ferpentine, and plain ve- neering ditto _____ — — o 9 o A flider fquare clamp’d or lip’d for cloth, cock beaded — o 2 6 Miter clamping ditto, each miter extra — — — o o 6 A flider with one pannel, lip’d for cloth — — — o 3 o Lining the flider with cloth — _ — — — 0 o 6 Frame back, each pannel — — - — — o o 6 A munting in plain back — — — — — 0 o 3 When made with three drawers, each inch in the drawers above eight inches deep _ _ _ - - o o 3 Stump r 7 3 £■ s - d - Stump feet the fame as common brackets. Lining up ends to form pilaflers, and putting on quarter fluff, or veneering ditto - - - - - - 026 Oiling and polifhing - - - - - - 00 9 A SERPENTINE DRESSING CHEST, With Straight Wings — as in Plate 1, No. 1. Four feet long, four drawers in the middle, and four ditto in each wing, cock beaded, aflragal or flone moulding on the edge of the top, or the edge veneer’d, and a firing in the upper corner, on common brackets - — — 3 10 0 EXTRAS. Each inch, more or lefs, in length - - — - 0 1 0 Ditto above 2 feet 8 inches high — - — — 0 0 6 Each drawer, more or lefs, in the middle — — — 0 3 3 Each partition, more or lefs — - — — — 0 0 6 Each drawer in the wings, more or lefs - — — 0 2 0 Each partition - - - - - - — 0 0 5 Lining each partition crofs-way — - — — 0 0 1 Veneering the top — — — - — — - - 0 1 2 Each joint in the veneer — — - — — — 0 0 7 Veneering each ferpentine drawer front - — — 0 1 0 Veneering each flraight drawer front — - — — 0 0 5 If cupboards in the wings — -for the price of ditto, fee Li- brary Writing Table, No. II. For the price of work not inferted here — See Serpentine and Straight -front Drefling Chejl. Oiling and polifhing - - - - - - 010 A SER- f 8 ] A SERPENTINE DRESSING CHEST, With Ogee Ends — as in Plate 1, No. 2, Three feet long in front, and fiveatback, aftragal or ftone £. s. d. moulding on the edge of the top, or the edge veneer’d, and a firing in the upper corner, four drawers in front, cock beaded, a cupboard in each end, one fhelf in ditto, veneer’d top, front, and ends, on taper flump feet —410 EXTRAS. Each inch, more or lefs, in front — — — - O Ditto at the back — — — — — — — o Ditto above 2 feet 8 inches high — — — — o Veneering inlide of doors, each — — — — o Each extra fhelf in the cupboard - — - - o If any other fort of flump feet — See Plate and Table of ditto. For the price of any other work in front or top — See Table of ditto. For the price of Aider, or any other work not inferted here — See Serpentine Dreffing Chef. Oiling and polifhing - — — o l o o 4 0 4 1 o o 6 1 o A FRENCH E 9 1 A FRENCH COMMODE DRESSING CHEST, as in Plate 1, No. 3, Three feet long, veneer’d top, front, and ends, three drawers £. s. d. in ditto, cock beaded, the drawer fronts to fit the fweep of the ends, aftragal or done moulding on the edge of the top, or the edge veneer’d, and a firing in the upper corner, on French feet, or common brackets - “35° EXTRAS. Each inch, more or lefs, in length — — — Ditto above 2 feet 8 inches high — — - Each drawer more - — - — — — - Each partition more ~ - — — — - Lining ditto each - — — — — — - If the front is commoded both ways, to be extra — For the price of any other work not inferted here — See Ser • pentine Drefling Chejt. Oiling and polifhing — — — — - 010 004 046 009 001 120 010 A KNEE-HOLE DRESSING CHEST, Three feet long, one long and fix fhort drawers in ditto, cock beaded, aftragal or ftone moulding on the edge of the top, or the edge veneer’d, and a firing in the upper corner, faft plinth, fix common brackets, or plain taper’d flump feet c 170 EXTRAS. t 10 ] EXTRAS. Each inch, more or lefs, in length - - - — Ditto above 2 feet 8 inches high - - - — Each long drawer, more or lefs - — — — — Each fhort ditto ------- Each long partition, more or lefs - - - — Each fhort ditto ------- Lining ditto crofs-way, each - - — - - Veneering each long drawer front — — - — Ditto each fhort — — — — — — — A cupboard in the knee-hole, with a flat door pannel plow’d in, the plinth or bafe moulding return’d round ditto - A frame in the knee-hole to receive the door — — For any work in ditto — See Counting- Houfe Bookcafe. Veneering ditto, or door frame, each — — — — Ditto crofs-ways, each ______ Veneering the pannel ______ An aftragal round the carcafe, under the top drawer - Two extra brackets in the knee-hole — — — — French feet or folid French brackets at fix corners — Two ditto in the knee-hole, extra _ - — — A bead round the bottom of carcafe or bafe moulding — An aftragal round ditto — — — — — — For the price of any work not inferted here — See Drejjing Chejt. Oiling and polifhing ______ £■ s. d. O 0 9 O 0 4 0 2 3 O 2 0 O O 6 O O 5 O O 1 O O 6 O O 5 O 4 0 O 1 0 O 0 9 O 1 0 O 0 6 O 1 0 O 1 0 O 3 0 O 1 0 O 1 0 0 1 6 0 1 0 A ROUND [ U ] A ROUND FRONT KNEE-HOLE DRESSING CHEST, Three feet long, one long and fix fhort drawers in ditto, £. s. d. cock beaded, 'aflragal or ffone moulding on the edge of top, or the edge veneer’d, and a firing in the upper cor- ner, fix French feet, common brackets, or plain taper’d flump feet - - - - - — -1150 EXTRAS. Each inch, more or lefs, in length - - — - Ditto above 2 feet 8 inches high — — — — If the front is made eliptic, extra — - — - Each long drawer, more or lefs - — — — — Each fhort ditto — — — — — — — Each long partition, more or lefs - - - - Each fhort ditto — — - - - — - Lining ditto crofs-way, each - - - - - Sawing long drawer fronts out of two-inch fluff, each cut Ditto, each fhort -------- Sawing long drawer fronts out of three-inch fluff, each cut Each fhort ditto — — — — — — — Glueing up long drawer fronts, each joint — — — Ditto, each fhort — — — — — — — Veneering each long drawer front - — - — Ditto, infide — — — — — — — — Veneering each fhort drawer front — — — — Ditto, infide — — — — — — — For cupboard in knee-hole — See Straight-front Knee-hole Dr effing Chejl. If fweep front door, extra — - — — — Ditto, frame to receive the door, extra - — - 008 004 0 2 0 03° 0 2 6 008 0 o 5 001 001 000 001 000 002 001 o o 10 006 006 003 014 008 A bead c 2 Nji [ 12 ] £■ A bead round the bottom of the carcafe or bafe moulding o An aftragal ditto — — — — — — - o Solid French brackets at fix corners — - — — o Two ditto in the knee-hole, extra — - — — o An aftragal round the carcafe under the top drawer • - o For the price of work not inferted here — See Round-front Dr effing Chefl. Oiling and polifhing ______ o s. d. i 3 i 6 3 o l o 1 2 1 o C OOOOOOOOOO 3 A SERPENTINE KNEE-HOLE DRESSING CHEST, Three feet long, with one long and fix fhort drawers in ditto, cock beaded, aftragal or ftone moulding on the edge of the top, or the edge veneer’d, and a firing in the upper corner, fix French feet, common brackets, or plain taper’d flump feet — - — — — — 250 EXTRAS. Each inch, more or lefs, in length _ — - Ditto, above 2 feet 8 inches high — _ — Each long drawer, more or lefs - _ _ Each fhort ditto _______ Each long partition, more or lefs _ — - Each fhort ditto _______ Lining each partition crofs-way _ _ - Sawing long drawer fronts out of twu-inch fluff, each cut Ditto, each fhort ditto ______ Sawing long drawer fronts out of three-inch fluff, each cut Ditto, fhort ditto ------- o o o o o o o o o o o 1 o 3 2 o o o o 0 4 9 8 9 5 1 1 o o O I o o Gluein Orq -Hu w|« to|. [ 13 ] Glueing up long drawer fronts, at per joint - - - Ditto, fhort ditto — - — - — — — Veneering long drawer fronts, each — — — — Ditto, each fhort ditto — Veneering partition edges afkew or crofs-way, at per foot extra An aftragal round the carcafe under the top drawer — A bead round the bottom of the carcafe or bafe moulding An aftragal ditto _______ For the price of cupboard in the knee-hole — See Straight- front Knee-hole Dr effing Chef. Sweep-front door, extra ______ Ditto, the frame to receive the door, extra - — - Solid French brackets at ftx corners — - — — Two extra ditto in the knee-hole _ _ _ — For the price of work not inferted here — See Serpentine DreJJing Chef. Oiling and polifhing ______ £■ s - d ■ 0 0 2 O O 1 O 1 O o o 6 O o oh 014 o 1 3 016 O 3 4 008 030 010 010 A LOBBY CHEST, Three feet fix inches long, three long and two fhort drawers in ditto, cock beaded, aftragal or ftone moulding on the edge of the top, or the edge veneer’d, and a firing in the upper comer, fall plinth or common brackets -130 EXTRAS. Each inch, more or lefs, in length - Ditto, above 3 feet 6 inches high - -006 -003 Each [ 14 1 £■ s. d. Each long drawer, more or lefs - - - O 2 6 Each Ihort ditto - - - o 2 o If made with three drawers in height, each inch in depth of drawer more than ten - - - o o 2 Each partition, more or lefs - - - o o 6 Lining ditto crofs-way, each - - - o o 1 Slipping drawer fides and plowing bottoms in, each drawer o o 3 Munting in each bottom - - - o o 3 Half ditto ------ - - o o It A front edge under the top or above the bafe moulding - o o 3 A frieze under the top moulding, veneer’d crofs- -way, w ith an aftragal at foot - - - o 1 6 Glueing up ends, top, or drawer fronts, either folid or to veneer on, at per joint - - - o o i Clamping the top end-way, to appear as folid - - o o 6 Veneering the top - - - o 1 o Each joint in the veneer - - - o o 6 Veneering each end - - - o 1 o Each joint in the veneer - - - o o 4 Veneering long drawer fronts, each - - o o 8 Ditto each fhort - - - o o 6 Each butt joint in the veneer - - - o o 4 Veneering partition edges alkew or crofs-way, at per foot extra o o Ot Making this cheft in two carcafes - - o 3 o For the price of any other work — See DreJJing Chejl. Oiling and polilhing ----- - - o o 9 If a rail at back and front, and the top fcrew’d on, no al- lowance to be made for a partition. ROUND [ 15 h ROUND-FRONT LOBBY CHEST, Three feet fix inches long, three long and two fhort drawers in ditto, cock beaded, aflragal or flone moulding on the edge of the top, or the edge veneer’d, and a firing in the upper comer, French feet, or common brackets - EXTRAS. Each inch, more or lefs, in length - Ditto above 3 feet 6 inches high - Eliptic fweep, extra from round front - Lining up ends to form pilaflers, putting on quarter fluff, or veneering ditto ------ Each long drawer, more or lefs - Each fhort ditto ------- If made with three drawers in height, each inch in depth of drawer more than ten ----- Each partition, more or lefs - Lining ditto crofs-way ------ Slipping drawer fides and plowing bottoms in, each drawer Munting in each bottom ------ Half ditto under the bottom -■*>--- A front edge under the top ------ A frieze under the top moulding veneer’d crofs way, with an aftragal at foot ------- Ditto, when pilafters ------ Glueing up ends or top, either folid or to veneer on, at per joint Sawing long drawer fronts out of two-inch fluff, each cut Ditto each fhort Sawing long drawer fronts out of three-inch fluff, each cut Ditto each fhort — — — — — £■ *. d. 1 12 o 008 003 026 046 036 026 O O 2-j 0 0 8 O O 1 OO3 003 O O if 004 0 1 9 023 001 001 O o Of o o if o o of Glueing t ] Glueing up long drawer fronts, each joint — - — Ditto each fhort — — — — — — — Veneering the top — — — — — — — Each joint in the veneer — — — — Veneering each end — — — — — — Each joint in the veneer ______ Veneering each long drawer front — — — — Each fhort ditto _______ Veneering long drawer fronts infide, each — _ _ Ditto each fhort _______ Each butt joint in the veneer — _ — _ _ Veneering partition edges afkew or crofs-way, at per foot extra For the price of other work not inferted here — See Round- front DreJJing Chef. Oiling and polifhing ______ £■ O O o o o o o o o o o o o s. d. O 2 0 1 1 o 0 6 1 o o 4 O 11 o 7 o 7 0 5 o 6 O Qi ° 9 C •0‘<2>*0 ,> 0°0 , 0 o 0<0<' < s><'0 0 A SERPENTINE LOBBY CHEST, Three feet fix inches long, three long and two fhort drawers in ditto, cock beaded, aftragal or flone moulding on the edge of the top, or the edge veneer’d, and a firing in the upper corner, French feet or common brackets — -250 EXTRAS. Each inch, more or lefs, in length — Ditto, above 3 feet 6 inches high ~ Each long drawer, more or lefs — 010 003 046 Each [ 17 ] Each fhort drawer, more or lefs - - - - If made with three drawers in heighth, each inch in depth of drawer more than ten — — — — — Each partition, more or lefs - - - - - Lining each ditto crofs-way - — - — — Slipping drawer fides, and plowing bottoms in, each drawer Munting in each bottom . - - — — — — Half ditto under the bottom - - - - - A front edge under the top _____ A frieze under the top moulding veneer’d crofs-way, with an aflragal at foot ______ Glueing up ends or top, either folid or to veneer on, at per joint Sawing long drawer fronts out of two-inch fluff, each cut Ditto, each fhort _______ Sawing long drawer fronts out of three-inch fluff, each cut Ditto, each fhort _______ Glueing up long drawer fronts, each joint _ _ _ Ditto, each fhort _______ Veneering the top -------- Each joint in the veneer ------ Veneering each end — ' — - _ — - Each joint in the veneer ______ Veneering each long drawer front _ _ _ _ Ditto each fhort _______ Each butt joint in the veneer _____ Veneering partition edges afkew or crofs-way, per foot extra Veneering long drawer fronts infide, each — - - Ditto each fhort _______ For the price of other work not inferted here — See Serpen- tine Drejfing Cheji. Oiling and polifhing ______ D £■ s. d. O 3 6 0 o 3 o o 8 o o 1 o 0 3 0 0 3 o o 1 2 o o 4 0 2 2 o o 1 0 o 1 0 o o| o 0 it o o °i o 0 2 0 o 1 0 1 O 0 o 6 o 1 0 o 0 4 o 1 o o o 9 0 o 6 o o o 4 o o 9 o o 6 o 1 o PAR- [ >8 ] PARTICULARS OF A FURNITURE DRAWER. Each fquare hole formed by partitions the depth of the drawer - -- -- -- - Each partition for rings, combs, &c., that are Aiallow - A glafs frame hing’d to a Aiding piece - — — A horfe behind ditto — — — — — — Framing the Aiding piece — — - - — A frame for the glafs to fall into — - — - Making the glafs frame, or piece the frame is hing’d to, fit a fweep front — — — — — — — A Araight-front drawer under the glafs — — — A fweep-front ditto — — — — — — A drawer in the end for ink, fand, and wafers — — A hollow for pins or pens _ _ _ _ _ Each fquare loofe cover — — — — — — Ditto to fit a fweep front — — — — — — Rounding or champhering each cover _ — — Veneering each cover ______ Hingingeach ditto -- — — — — — Putting a lock on ditto — — _ — Each fquare box without a top — — — - _ Ditto to fit the fweep of front - — ' _ - — Price of covers to ditto as above. Rabbiting the top, and fixing one part fa A, the other part hing’d to ditto — — — — — — — A fquare box, with the top cut off, and a rim infide ditto - Ditto to fit a fweep front ------ An empty lift-out — — — — — — — Each hole in ditto form’d by partitions _ _ _ £■ s. d • O o 3 O o 2 o 3 9 0 o 9 0 o 4 o 1 o o 0 3 0 1 o o 1 6 o 2 3 0 o 4 0 o 4 o o 6 0 o 2 o o 1 0 o 3 o 0 3 0 o 10 o 1 4 0 o 6 o 1 8 o 3 o 0 o 9 0 0 2 Each [ 19 3 £■ Each falfe bottom under rings, combs, or lift-out - - o If made to tilt - -- -- - -o A plain comb tray — — — — — — — O Each finger hole in ditto — — — — — — O Scolloping the edges ------ O Rabbiting the bottom on ditto - - - — - o If made with a drawer to ditto — - — — - o A fquare pincufhion board, with a moulding round ditto - O A frame for ditto — — — — — — — O An oval ditto, and preparations - - - - - o A fquare brufli top - - — — - — — O An oval ditto, and preparations - — - - - O A plain folid Aider, fquare clamp’d or lip’d for cloth — O A flap to ditto, clamp’d ------ O A horfe to ditto — — — — — — — O A bottom under ditto - — - — o Hinging the flap with a bead and band round ditto - o Making the Aider to fit the infide of round front — — o Ditto ferpentine — — — — — — — o Lining the Aider with cloth - — - — - o Ditto when a flap - -- - - -- o Lopers to fupport drawer — - — - - - o Lining infide of drawer with bead fluff - - - o Ditto, when round front - - - - - — o Ditto, when ferpentine — — - — - - o For the price of glueing colour’d wood on partition edges — See Secretary Drawer. Crofs -banding, &c . — See Table of ditto. Every inch above three feet in the length of drawer — o s, o 0 1 o o o 2 o o 2 0 2 2 1 1 O O o o 0 1 3 o o o o d. 2 1 2 1 4 2 6 6 9 o 6 o o o o 6 8 4 6 9 o o 6 8 9 2 D 2 ASE- [ 20 ] A SECRETARY DRAWER, Three feet fix inches long, front cock beaded, fix fmall £. s. d. drawers, and fix letter holes- infide - - - —0180 EXTRAS. Each inch, more or lefs, in length - — — — Each fmall drawer, more or lefs, under 12 inches, including partition - — — Each drawer above 12 inches long and 3 inches deep See Counting-houfe Bookcafe . Putting in partition for ink, fand, and wafers — — A hollow for pens - — — — — - — Each letter hole, more or lefs — — — — ~ Each fpace for books or paper - — — — — Each arch with a plain fweep If a fcollop arch ------- Each circular arch, with a firing m the fweep part - - A folid piece for a label, firaight — - — — Each circular arch with a cock bead - - - — Veneering each arch — — — — — — Lining up the ends with thin fiuff to receive the infide work A plain profpedl door — — — — — — Hinging ditto on the miter - - — - - Each folid flap to inclofe drawers or letter holes, hing’d on the edge — — — — — — — — If hing’d as fecretary-drawer front — — — — Square clamping each flap ______ Veneering each flap ______ Miter clamping ditto, each miter extra _ - 0 0 2 0 1 a 0 0 6 0 0 4 0 0 3 0 Q 3 0 O 1 0 O *2 0 O 2 0 O Oj 0 O 3 0 O oj- 0 O 6 0 1 3 0 O 6 0 2 6 0 3 6 0 0 3 0 0 3 0 0 6 A plain [ 21 ] £. s. d. A plain tambour to inclofe the centre part of the inflde, to run right and left — — — — — — Veneering each fmall drawer front or profpedt door - If a fmall drawer front reprefents two in length - - Ditto in width _______ A firing round the outflde of drawer front or profpedl door, or letting in ditto to form a fquare pannel, each - - Letting a firing in a profpedl door to form a pannel, with circular top _______ A Aiding profpedt, the pilafler drawer to take out behind Each pilafler drawer in front, with plain flutes — — Counter flutes, extra ______ Glueing black, white, or other veneer, on the edges of par- titions ________ A triple firing _______ Veneering the front and flanding board, or banding ditto for cloth ___ _ ____ Lining ditto with cloth _ _ ____ A Aider inflde drawer, with a flap, horfe, and bottom - Veneering the drawer front outflde _ _ _ _ Making ditto round front _____ Ditto ferpentine _______ A flap withinfide the front, hing’d _ _ _ _ Square clamping ditto ______ Veneering round front drawer outflde _ _ _ _ Ditto ferpentine _______ Laying the veneer of round front drawer in two pieces — Ditto ferpentine ditto ______ Hinging front with dolphin hinges, extra _ _ _ For the price of crofs-banding. &c . — See Tables. If the inflde work of fecretary drawer be round fronted or concaved, to be extra ------ 050 0 o 1 001 O O 003 004 026 016 006 010 0 2 0 OlO 00 6 056 009 030 036 016 003 010 O 1 2 014 016 003 050 Each t 22 j Each extra drawer above fix, with round or concave front Ditto arch, extra ------ Profpedt doors, extra ------ Veneering ditto ------ Ditto each drawer ------ C xSX3 ,, 0 4 0' > ‘<2>*04 > 0" , <3> 0 <£> < 3 A SECRETARY, Three feet fix inches long, fix fmall drawers, and fix letter holes infide, the drawer front cock beaded, two flat-pan- nel’d doors under ditto, pannels plow’d in, one book flielf infide, aflragal or ftone moulding on the edge of the top, or the edge veneer’d, and a firing in the upper comer, on plinth or common brackets - - - - -1190 £. s. d. Ol6 - OOl - 0 0 6 - 0 0 2 - O O 1“ EXTRAS. Each inch, more or lefs, in length - Each clothes-prefs lhelf ------ Each front to ditto - - - - - For the price of extra work in ditto — See Clothes Prefs. Glueing up ends, top, drawer front, or pannels, either folid or to veneer on, at per joint - Veneering top -------- Ditto each end -------- Each joint in the veneer of top - Ditto in the veneer of end ------ Veneering the top, when a bookcafe - 006 016 006 OOl 010 010 006 004 006 Veneering [ 23 ] £■ Veneering the door frames ------ o Ditto crofs-way, extra ------ o Veneering the pannels - - - , - o Each joint in the veneer - - - - - - o Veneering the drawer front outfide - - - o For extra work in ditto — See Secretary Drawer. Veneering partition edges afkew or crofs-way, per foot extra o An aftragal round the carcafe, above or below the doors - o A frieze veneer’d crofs-way, with an aftragal at foot, under the top moulding - Each long drawer inlide of doors, no locks, fcratch beaded or firings ------ o Each fhort ditto, no locks ------ o Cock beading each long drawer, extra - - - - o Ditto each fhort ------ - o Each partition o Lining ditto crofs-way, each - 0 Veneering drawer fronts — See Lobby Chejl. French feet, French brackets, or other work in carcafe — See Drejfing Chejl. Doors clamp’d with fquare clamps, and veneer’d with a plain veneer, to be the fame as pannel doors. If three drawers underneath in place of doors, to be the fame as doors with one fhelf infide and grooves. Oiling and polilhing ------ - o s. 2 1 1 O o 0 1 1 2 1 o o o o o d. o o 6 6 9 o 6 4 9 4 3 6 9 A ROUND- I 24 ] A ROUND-FRONT SECRETARY, Three feet fix inches long, the drawer front cock beaded, £. s. d. fix fmall drawers and fix letter holes, ftraight infide, two flat-pannel’d doors under ditto, the framing plow’d and pannels bent in, one book fhelf infide, aftragal or ftone moulding on the edge of the top, or the edge veneer’d, and a firing in the upper comer, French feet or common brackets _ - - - - - - - 2 10 o EXTRAS. Each inch, more or lefs, in length - Each clothes-prefs fhelf ------ Each front to ditto ------- For the price of extra work in fhelves — See Clothes Prejs. Veneering the door frames long-way - Ditto crofs-way -------- Glueing up the pannels to the fweep, at per joint Veneering ditto, each ------- Veneering the drawer front outfide - For the price of extra w r ork in ditto See Secretary Drawer. Veneering partition edges afkew or crofs-way, per foot extra An aftragal round the carcafe, above or below the doors A frieze under the top moulding veneer’d crofs-way, with an aftragal at foot - Each long drawer infide the doors, fcratch beaded Each fhort ditto _______ Each partition Lining ditto crofs-way, each - 009 0 1 9 009 026 03 6 001 010 010 O o oh 0 12 0 1 9 032 0 2 3 OO 9 001 Veneering [ 25 ] £• s - d - Veneering drawer fronts, &c. — See Round-front Lobby Cheft. For any extra work in carcafe — See Round-front Dreffmg Cheft. Doors clamp’d with fquare clamps, and a plain veneer, to be the fame as pannel doors. If three drawers under, in place of doors, to be the fame as doors with fhelf and grooves. Oiling and polifhing - — — — — - 00 9 A SERPENTINE-FRONT SECRETARY, Three feet fix inches long, the drawer front cock beaded, fix fmall drawers and fix letter holes infide, two flat pan- nel doors, or ditto glued up, fquare clamp’d, and veneer’d on one fide, one book fhelf infide, aftragal or ftone moulding on the edge of the top, or the edge veneer’d, and a firing in the upper corner, French feet, or com- mon brackets - - - - - - "*340 EXTRAS. Each inch, more or lefs, in length — - — — o Each clothes-prefs fhelf, without a front — - — o Each ferpentine front to ditto - — — — — O For the price of extra work in fhelves — See Clothes Prefs. Veneering the door frames long-way - - — — o Ditto crofs-way - -- -- --- o Veneering the pannels, each — - — — — o Veneering the drawer front out fide - — — — o E 1 o 2 O 1 o 3 0 4 o 1 3 1 2 For [ 2 6 ] For the price of extra work in drawer front — See Secretary Drawer. Veneering partition edges afkew or crofs-way, per foot extra An aftragal round the carcafe above or below the doors — A frieze under the top moulding veneer’d crofs-way, and an aftragal at foot — — - — — Each long drawer infide the doors, fcratch beaded — — Each fhort ditto — — — — — — — Cock beading each long drawer front, extra — - Ditto each fhort — — — — — — — Each partition ------- Lining ditto crofs-way - — — — — - Veneering drawer fronts, ends, See. — See Serpentine-front Lobby Chejt. For extra work in carcafe — See Serpentine Drefling Chejt. Oiling and polifhing ------ £. s. d. O O Oj 0 i 4 0 2 2 038 026 007 005 008 001 010 C ■©*©H*0^0-->0* < £ > ' > O c O i O»0' D A BUREAU, Three feet long, four drawers in ditto, cock beaded, fix fmall drawers and fix letter holes infide, on plinth or common brackets — — - — — -1120 EXTRAS. Each inch, more or lefs, in length — Each long drawer, more or lefs — - Each fhort drawer — - — — Each partition, more or lefs - - -009 -023 -019 -00 6 Lining C 27 ] Lining partitions crofs-way, each - - - - Slipping drawer fides and plowing bottoms in, each drawer Munting in each bottom - — — - — — Half ditto under the bottom — — — — — Glueing up ends, top, fall, or drawer fronts, either folid or to veneer on, at per joint - - — - — Square clamping the fall either folid or to veneer on - Miter clamping ditto, each miter extra - - - Veneering the fall, each fide — - — - — Mitering the veneer to reprefent clamps - — — Veneering the top — - — - — — — Veneering long drawer fronts, each — — - — Ditto each fhort _______ Each butt joint in the veneer — - — _ _ Each joint in the veneer of fall, top, or drawer fronts — Veneering partition edges afkew or crofs-way, per foot extra Veneering the ftanding board - — — — - Veneering the fall and ftanding board to receive cloth, or finking ditto out of the folid - _ — — Lining ditto with cloth ______ Veneering the ends outfide, each — - _ — Each joint in the veneer Veneering the infide of ends, and up the dopes — - A pair of flat-pannel doors in the place of the three lower drawers, with three clothes fhelves infide, extra from drawers - — — — - — Each front to ditto — — — _ _ _ For the price of extra work in ditto — See Clothes Prefs. Veneering the door frames - — _ _ _ Ditto crofs-way, extra Veneering the pannels ______ £. s. d. OOl OO 3 00 3 0 O lj- 001 006 006 O O Q 0 0 8 O06 0 0 6 004 OO 4 0 0 6 o o oi 00 6 010 006 010 003 010 040 00 6 020 010 010 Each e 2 [ 28 ] £• s - d • Each joint in the veneer, at per foot - - - -002 Framed back, each pannel - - - - - 006 Munting in a plain back - - - - - - 003 For the price of extra work infide — See Secretary Drawer. For the price of French feet, French brackets, or other work not inferted here — See Drejfing Chejl. Oiling and polifhing - - - - - -009 C x£>*0 , «S>^*0*0''0 < 0 A DOUBLE CHEST, Three feet fix inches long, fix feet four inches high to the top of the cornice, fix long and two fhort drawers in ditto, cock beaded, on plinth or common brackets —200 EXTRAS. Each inch, more or lefs, in length - - - - Ditto in height _______ Each long drawer, more or lefs _ _ _ _ Each fhort ditto _______ If only fix drawers in height, each inch in depth ot drawers more than ten _______ Each partition, more or lefs — — — — — Lining ditto crofs-way, each _ — _ — — Slipping drawer fides, and plowing bottoms in, each drawer Munting in drawer bottoms, each _ _ _ — Half ditto under the bottom — — — — — For the price of veneering drawer fronts, ends, &c. — - See Lobby Chejl. Veneering partition edges alkew or crofs-way, per foot extra 010 003 02 6 020 002 006 001 003 003 o o l\ o o of Veneering [ 29 ] . s . d. Veneering partition edges with king, tulip, or any other hard wood, at per foot — Lining up and canting the corners of upper part - - Ditto the lower part — — — — — — Gothic columns, extra from canted corners — — — Loofe cornice frame - — — - — — If a loofe cornice frame with a frieze, the frieze not to be reckoned in height. Falfe top to ditto — — — — — — — Veneering the frieze crofs-way, and an aftragal at foot of ditto Ditto, when a Gothic cornice — — — — — If frieze veneered long- way — — — — — Loofe frame for furbafe moulding - - — - Ditto for plinth or brackets — — — - — Canting the furbafe moulding — — — — — Ditto the bafe and brackets — — — — — Canting cornice frame and cornice broke round ditto — Breaking the aftragal and frieze round — — — For the price of French feet, French brackets, Aider, or other work not inferted here — See Drejfmg Chejl. For the price of Gothic cornice, dentil, fafcia, or crofs- mouldings, &c. — See Tables of ditto. Oiling and polifhing — — — o o 1 030 020 020 010 006 016 o 1 9 o 1 3 009 010 004 010 016 006 C i €»0 , <5*©00€>000 3 A ROUND-FRONT DOUBLE CHEST, Th ree feet fix inches long, fix feet four inches high to the top of the cornice, fix long and two fliort drawers in ditto, cock beaded, on French feet or common brackets 300 EXTRAS. C 30 3 EXTRAS. Each inch, more or lefs, in length — — — — Ditto in height _______ Each long drawer, more or lefs - - - - Each fhort ditto If only fix drawers in a height, each inch in depth of drawer more than ten _______ Each partition, more or lefs _ — — — — Lining ditto crofs-way, each — — _ — _ For the price of glueing up drawer fronts or ends, and ve- neering ditto — See Round-front Lobby Chejt. Veneering partition edges afkew or crofs-way, per foot extra Loofe frame for cornice or plinth - - — - Ditto for furbafe _______ Veneering the frieze, with an aftragal at foot of ditto — Ditto, when Gothic cornice — — — — — For the price of other work See Straight- front Double Chejt. Oiling and polifhing ______ £■ s. d. O 1 3 O 0 4 O 3 6 O 2 6 O 0 2i O 0 8 O 0 1 O 0 Ot O 1 6 O 0 10 0 2 0 0 2 3 O 1 8 C •0»0»<2*’0 < *©-‘©' •<£» ■©»©■'©' D A LOW CLOTHES PRESS, Four feet long, and four feet high, in onecarcafe, two flat- pannerd doors, pannels plow’d in, three clothes fhelves infide, two fhort drawers at bottom, cock beaded, aftragal round the carcafe between the doors and drawers, aftragal or ftone moulding on the edge of the top, on plinth or common brackets _____ - 1 12 o EXTRAS. t 3 1 ] EXTRAS. £■ Each inch, more or lefs, in length — — - — o Ditto in height - — - — — o Each fhelf front — — — — — — - o Veneering the top - — - — — — — O Each joint in the veneer of ditto, at per foot — — — o Veneering ends, each — — — — — — O Each joint in the veneer of ditto, at per foot — - o For the price of other work not inferted here — See Clothes Prefs. Oiling and polifhing ------ o s • d • o 8 o 3 0 6 1 3 0 2 1 3 o 1 o Ck£>«Ok£h><2>*>0<>0 , 0< > 0«S>0* < ©•x2>»<2>' 0 A ROUND-FRONT CLOTHES PRESS, Four feet long, fix feet nine inches high to the top of the cornice, two flat-pannel’d doors, the framing plow’d, and the pannels bent into ditto, five fhelves in the upper part, two long and two fhort drawers in the lower part, cock beaded, on French feet or common brackets — EXTRAS. Each inch, more or lefs, in length — — — — Ditto in height — — — — — — — Each long drawer, more or lefs — — - — Each fhort ditto — — — — — — — Each partition, more or lefs - - — - - Lining ditto crofs-way, each — — — — — Each fhelf, more or lefs - Each front to ditto _______ Veneering each fhelf front _____ Veneering each long drawer front _ _ _ _ Ditto each fhort Veneering door frames long- way - — — _ Ditto crofs-way, extra ------ Glueing up the pannels to the fweep, at per joint — — Veneering fweep pannels, each — _ - _ _ Veneering partition edges afkew or crofs-way, per foot extra F 3 11 0 0 1 3 0 0 4 0 4 0 0 3 0 0 0 9 0 0 1 0 1 9 0 0 9 0 0 3 0 1 0 0 0 9 0 2 8 0 1 6 0 0 4 0 1 3 0 0 Oj Doors [ 34 ] Doors glued up, clamp’d, and veneer’d, confidered the fame s. d * as thofe defcribed in the preamble. Veneering doors infide — — — - — — 013 For the price of work not inferted here — See Clothes Prefs , Round-front Lobby Chejl, or Double Chejl. Oiling and polifhing - - — - - - 019 A WING CLOTHES PRESS, as in Plate 3. Six feet eight inches long, fix feet nine inches high to the top of the cornice, two flat-pannel’d doors to the upper carcafe of middle part, pannels plow’d in, fix clothes (helves infide ditto, two long and two (hort drawers in the lower part, cock beaded, the wing doors to open from top to bottom, with two pannels in each plow’d in, four fafi: (helves infide one wing, turn’d pegs in the other, loofe cornice, fram’d backs to the top and bottom of middle part, fall: plinth, and loofe cornice frame “55° EXTRAS. Each inch, more or lefs, in length - - - -016 Ditto in height - - — — - — — 006 Glueing up the ends of middle part, drawer fronts, or pan- nels, at per joint - - - - - - 001 Glueing up out ends of wings, at per joint — — — o O 3 Putting in the pannels with a bead behind, each pair —010 Veneering each long drawer front - - - - o o 8 Ditto each fhort - - — — - _ — 006 Each C 35 1 Each butt joint in the veneer — — - - Veneering door frames of middle part long-way — Ditto crofs-way, extra - — - — — Veneering door frames of wings long- way, each door Ditto in bottom part — - - Ditto crofs-way, each door extra - Veneering each long pannel - - Ditto each fhort — - — — Each joint in the veneer, per foot in length Veneering the outfide ends of wings, each Each joint in the veneer, per foot in length Veneering the breaks of middle carcafe Veneering frieze long-way, with an aftragal at foot of ditto Ditto crofs-way — — — — — Ditto, when a Gothic cornice — — — _ _ Each gib joint in the furbafe — — _ _ _ Framing the lower part of wing doors, folid, or veneering ditto to reprefent three fham drawers, cock beaded, each door extra - — — — — If drawers in the lower part of wings, dedud for lower framing each door — — — Each drawer in the wings — - _ _ _ Each partition — - - _ _ _ Lining ditto crofs-way — — Each bracket in the top part of wings or center, to turn with a rule joint to receive the clothes pegs - - Arms for gowns hung with fwivels, each - _ _ If doors to the lower part of middle carcafe, dedud for drawers and partitions as above, and add the price of doors. £■ s. d. O o 4 O 2 0 0 1 6 o 1 o o o 9 o 0 8 o 1 0 o o 9 o o 2 o 1 9 o o 1 i o 1 0 o 2 o o 2 6 o 2 9 o 1 o o 1 0 o 2 6 o 2 o o 0 5 o 0 i o 1 0 o o 6 F 2 Cleaning [ 3 ^ 3 Cleaning the infide of carcafe - A loofe frame for the plinth - Each plain pilafter on the ftiles of wing doors Veneering each pilafter long-way - Ditto crofs-way - A fmall moulding, miter’d at top and bottom, to form a cap and bafe, each pilafter - Mitering a fillet round the pilafter to form a pannel, each Ditto a fmall moulding - For pilafters to the top and bottom of middle part, and breaking mouldings round ditto — See Straight -front Li- For bead and butt pannels in backs, each pannel extra Fram’d backs to the wings, each pannel - For the price of other work not inferted here — See Clothes Prefs. Oiling and polifhing - £. s. d. O 1 o 030 009 004 006 006 010 016 003 006 030 A PRESS BEDSTEAD, Four feet long, fix feet nine inches high to the top of the cornice, all folid, plain cornice, two doors with one flat pannel plow’d in, and two fliam drawers in each door, or front fram’d in one and hing’d under the cor- nice, one drawer at the bottom, cock beaded, two fram’d backs with two pannels each, on plinth or common brackets EXTRAS. { 37 ] EXTRAS. * £■ s - d. Each inch, more or lefs, in length - Ditto in height - -- -- -- - Each fhort drawer ------- A flap at the bottom of the front, hing’d to let down or made to take off ------- Square clamping ditto ------ Veneering each long drawer front - Ditto each fhort ------- Making the ends to open in the middle - Ditto to open at the back, and gibbets to fupport the cornice Hinging the doors on the miter to fold againA the ends Square clamping the ends, each clamp - Miter clamping ditto, each miter extra - Hinging the front under the cornice, the hinges not to fhew in front -------- Veneering the door frames long-way - Ditto crofs-way, extra ------ Veneering each upper pannel - Ditto each lower ------- Each joint in the veneer, at per foot in length Veneering the frieze, with an aflragal at the foot of ditto, long-way - -- -- -- - Ditto crofs-way ------- Making the above to reprefent a clothes prefs, with a fur- bafe moulding round rhe carcafe, when the front turns up Putting in the pannels, with a bead behind, each pair For the price of French feet or brackets — See Drejfing Chejt. Oiling and polifhing ------ A plain bedftead, with fwing feet, and a rail fram’d between A Araining rail to ditto - - 008 003 020 020 006 008 006 040 080 0 2 0 004 0 0 6 0 2 6 O23 Ol6 OlO 009 0 0 2 O 1 O Ol6 036 010 Ol6 05° 0 0 6 Temporary [ 38 1 £■ *• d. Temporary ports, turn’d, and fix’d into the fides with fcrews and plates - Folding ports, with one joint to each, and fram’d into the top of the fides ------- Ditto, with two joints, each - A tefter lath, hing’d, and fixing rod to ditto - The grooves in the lath for the curtains to Aide in, in place of rods, extra ------- Colouring and polifhing a plain bedrtead - Colouring and polifhing a pair of pillars - Nailing in facking - If two pannels in each door and no fham drawers, dedudt If the ends take apart and the bottom drawer made a fepa- rate carcafe, with an aftragal in the front and ends 009 030 040 030 026 010 010 006 010 026 No. I. A TABLE BEDSTEAD, Three feet fix inches long, three feet fix inches high, the top miter clamp’d at the front corners, top and front to lift up, fupported with quadrants, the front fram’d to reprefent two doors, with fiat pannels plow’d in, two fham drawers at the bottom of ditto, fram’d back, two pannels, artragal or ftone moulding on the edge of the top, on plinth or common brackets - - - -150 EXTRAS. Each inch, more or lefs, in length - - - -006 Ditto in height - _ _ . _ _ _ -003 Square / C 39 ] £■ Square clamping the ends, each clamp - - - o Miter clamping ditto, each miter - - - - - o Making the ends to open half way - o Glueing up ends, top, or pannels, either folid or to veneer on, at per joint -------o Veneering the top - -- -- - -O Each joint in the veneer of top - - - - - o Veneering ends, each ------ O Each joint in ditto - -- -- -- o Veneering the door frames long- way - - - o Ditto crofs-way, extra ------ o Veneering the pannels - o Each joint in the veneer of ditto - - - - - o Putting in the pannels with a bead behind - - - o For the price of French feet or brackets — See Drejfing Chejl. Oiling and polifhing - -- -- -- o A plain bedftead, with fwing rail and feet - - - o For any extra work in ditto — See Prefs Bedflead. C >0*0>0*0o0t«2>«2) < ’0' > 0‘0' a s. d. o 4 o 6 2 O 0 1 1 o 0 6 1 o ° 3 2 O 1 O i 6 0 6 1 o ° 9 4 6 No. II. A TABLE BEDSTEAD, Three feet fix inches long, three feet fix inches high, two flat-pannePd doors, pannels plow’d in to open to the bafe moulding, with aftragal or hone moulding on the edge of ditto, fram’d back, two pannels, on plinth or common brackets - - - - - _ _ -110 EXTRAS. [ 40 ] EXTRAS. £' d. Each inch, more or lefs, in length - - - -006 Ditto in height - - - - - - 003 Making part of the top to fold - - - - .- 010 If above four feet high, and made to take to pieces, reckon it as a Prefs Bedflead. If the front and top made to. lift up, and fupported with iron flays - - - - - - - 016 If the front .is made to reprefen t a lobby, with the front ve- neer’d and cock beaded, extra - - - - - 016 For the price of other work not inferted here — See Table Bedjlead No. 1 , or Lobby Chejl. Oiling and polifhing ^ - - - * - - 009 0<^<^k3m<0>o<2><-^«QxxQ v -Qk'<3>0 * • n w ..jr . • J . <2 A BUREAU BEDSTEAD, Three feet fix inches long, to fhew four drawers in front, cock beaded, on plinth or common brackets - - o 15 6 EXTRAS. Each inch, more or lefs, in length - - - -004 Making the front to take off, the fall hing’d to fold upon the top, and a plain back - - - - - 026 If the front is made to lift up with the fall, and fupported with iron flays, extra - «-■ - - - -01 6 Fram’d back, each pannel - - - - - - 006 Munting [ 41 1 £■ s - d - Munting in a plain back — — - - -004 A pair of flat-pannel’d doors, pannels plow’d in, extra from a fall front - - — — — — — — 02 6 For the price of work not inferted here — See Dejk or Drejf- ing Chejt. Oiling and polifhing — - — — - -009 For the price of Bedftead — See Table Bedjlead No. 1 . A LIBRARY PRESS BEDSTEAD, With Breaks, Five feet three inches long, fix feet nine inches high to the top of the cornice, four doors, with two flat pannels each, pannels plow’d in, the middle doors faft to the breaks, and to open to the bafe moulding, fram’d back, four pannels, on faft plinth — - — - — 3100 EXTRAS. Each inch, more or lefs, in length - — - — o o 10 Ditto in height — — — — — — — 004 Glueing up the ends, either folid or to veneer on, at per joint 003 For the price of veneering pannels, ends, or breaks — See Wing Clothes Prefs. Veneering the door frames long- way, each pair of upper doors 020 Ditto crofs-way, extra — — - — - - 016 Bottom doors, long- way — — — — — — 016 Crofs-way, extra - - - - - - - 010 Veneering the frieze and an aftragal at foot of ditto, long- way - — — — - — — — 030 Ditto crofs-way, extra - - - — - - 010 g If C 42 ] If doors hing’d on the miter — — Oiling and polifhing, each foot in length A plain Bedftead, as in Prefs Bedftead For the price of extra work — See ditto. C •0-*®*0«0*0‘>0*0« , 0*©o0" j £. s. d. -02 6 - o o 6 - o 5 6 A BOOKCASE, Three feet long, and three feet three inches high to the top of the cornice, the ends nine inches deep infide in the clear, two fafh doors, fix fquares in each, and three fhelves infide - — - — — - - 0150 EXTRAS. Each inch, more or lefs, in length, height, or width of ends — — . — — — - — — o Each fquare in the doors, more or lefs - — — o Each fhelf, more or lefs than three — — - - o Every three inches above three feet long in extra fhelves o If the ends are bevel groov’d — - - - — o If fmall grooves, and the ends of fhelves fhoulder’d — o An upright partition, groov’d on both fides — — o Ditto, bevel groov’d — - — - — — o Ditto, with fmall grooves, and the end of fhelves fhoulder’d o Saw-teeth racks to fupport the fhelves, extra from grooving o Ditto, when an upright, extra - — - - — o It two upright grooves in each end, and notches to receive the ends of fhelves, when the grooves are not to fhew in front, each height of notches _____ 0 Ditto, w T hen three grooves, each height of notches — — o 0 3 0 3 o 6 0 1 1 o 1 o 3 o 4 o 4 o 1 6 1 6 O 1 2 O 2 Each [ 43 ] s. £■ Each extra fhelf, when ditto - — - — ~ o Glueing up the ends, either folid or to veneer on, at per joint o Veneering each end — — — — Each joint in the veneer — — — — Veneering door frames long-way — — Ditto crofs-way, extra - - - — Loofe cornice frame — — — — Falfe top to ditto — — — — — Veneering frieze crofs-way, with an aftragal at foot Ditto long- way ______ Ditto crofs-way, when a Gothic cornice - When loofe cornice, the frieze not to be reckon’d in height. For the price of Gothic cornice, dentil, or fafcia — See Ta- ble of ditto. Letting in quarter fluff for fluting, extra from veneering frieze — _ — — _ — — o Serpentine top, as in plate 7, fig. t, extra from ftraight — o Circular top, as in plate 7, fig. 2, extra from ftraight — o An eliptic top _______ o Each Aiding candle board — — - - — o Fram’d back, each pannel - — — — — o Munting in a plain back _____ — o For the price of extra work in doors — See Tables of ditto. Doors, when hung upon the miter - — — — o For bead and butt pannel, each pannel extra — — o Putting on a latch - — - — — o Oiling and polifhing ______ o - o - o - o - o - o - o - o - o - o o o o 0 2 1 1 0 1 1 1 d. 8 1 9 3 o 6 o 6 6 o 9 0 6 18 6 16 o 17 6 1 o o 6 0 3 1 6 o 3 o 6 0 9 G 2 A COUNTING- C 44 J A COUNTING-HOUSE BOOKCASE, Three feet long, and three feet three inches high to the £. s. d. top of the cornice, the ends nine inches deep infide, two flat-pannel’d doors, the pannels plow’d in - - o 12 6 EXTRAS. Each inch, more or lefs, in length, height, or depth - Each joint in the ends or pannels — - — - Veneering each end — — — — — — Each joint in the veneer ------ Veneering each pannel - — — — Each joint in the veneer — — — — - Veneering door frames long- way - - - - Ditto crofs-way, extra ______ Loofe cornice frame ______ Veneering the frieze crofs-way, with aftragal at foot - Ditto long-way ________ For the price of Gothic cornice, dentil, or fafcia — See Ta- ble of ditto. When a loofe cornice, the frieze not to be meafured in the height. Letting in quarter fluff for fluting, extra from veneering frieze ________ Each partition or fhelf acrofs the bookcafe _ - _ Each upright ditto for books - - _ - _ Scolloping ditto, each ______ Each letter hole _______ Each plain arch _______ o o o o o o o o o o o o o o o o 0 3 o 1 0 9 0 3 1 o 0 3 2 o 1 6 1 o 1 6 1 o o 6 o 6 o 4 O 2 O 4 o 1 Each o 1 o Each drawer not exceeding twelve inches long or three inches deep, including partition — — - — o Each ditto more than twelve and not exceeding eighteen inches, flip - — — — — o Each ditto above eighteen inches long, flip — — — o Each inch more than three in depth — — — — o Fram’d back, each pannel — — - — — o Munting in a plain back — — - — — o Oiling and polilhing ______ o l l o o o o 3 6 i 6 3 6 A STRAIGHT-FRONT LIBRARY BOOKCASE, Five feet long, and eight feet high to the top of the cor- nice, the lower ends one foot eight inches wide infide, the upper ditto ten inches wide inflde, two falh doors to the upper part, flx fquares in each, two flat-pannel’d doors to the lower part, pannels plow’d in, an upright partition in each carcafe, groov’d on both fldes, flx Ihelves in the upper and two ditto in the lower part, fram’d backs, flx pannels, and fafl: plinth - - -390 EXTRAS. Each inch, more or lefs, in length — _ _ _ Ditto in height or width of ends, upper or lower part - Each extra carcafe in the top part — _ _ _ Ditto in the lower part — — — ~ — — — No charge to be made for more than three carcafes in each part. o 1 o 003 o 1 6 0 2 0 [ 45 ] £. s. d. If fixed frames to reprefent doors for curtains, dedudt the price of doors, then add for each frame - — Plain pilafters glued on the ftiles of doors, or frames of the upper part, each pilafter — — — — — o Ditto on the lower doors or frames, each — - - o Falfe ends to receive pilafters, either upper or lower part, each end — — — — — — — — q The ends block’d to receive pilafter, when two carcafes meet — — — — — ___ 0 Getting out and fixing plain pilafters to the upper ends, each - — — - — — — _o Ditto on the lower ends, each — — — — - o Veneering pilafters of upper part long-way, each - - o Ditto lower part, each — — — — — — o Veneering ditto crofs-way, extra each — - — o Veneering each edge of ditto — — — — — o Mitering a fmall moulding round the top and bottom, to form a cap and bafe, each pilafter — - — — o A moulding miter’d round, to form a pannel, each pilafter, top part - — — — — — o Ditto, bottom part — — - -o Breaking the plinth round the pilafters, each miter — o Each extra miter in the furbafe — — — — o Each ditto in the moulding under the upper doors — o A loofe cornice frame — o Veneering the frieze crofs-way, and an aftragal, at per foot o Ditto long- way — — — — — — — o A frieze under the furbafe moulding, with an aftragal, at per foot - — — — - — — — o a Breaking ditto round pilafters, each miter — — - o 2 o o 8 0 6 2 O 1 O 1 O ° 9 o 4 ° 3 O 2 O 1 0 6 1 o ° 9 O 2 O 1 0 1 1 2 O 3 O 1 Each [ 47 ] £■ *■ d - Each extra miter in the cornice when broke round the pilafters - -- -- -- “O Ditto the aftragal -------o Veneering the plinth long- way, per foot - - - o Ditto crofs-way, per foot ------ O For the price of drawers in the lower part, doors, backs, fhelves, or any other work not inferted here — See Li- brary with Breaks. Oiling and polifhing, at per foot in length - - - O ° 3 o o O 1 O 2 o 4 A LIBRARY BOOKCAS&, as in Plate i. Six feet long, eight feet high to the top of the cornice, the middle ends of lower part one foot eight inches wide infide, the middle ends of upper part one foot three inches wide infide, fquare fafh doors to the upper part, fix fquares in each, flat-pannel’d doors to the lower part, or three drawers in each wing, the lower part made in one carcafe, three clothes fhelves in the center, and one book fhelf in each wing, the upper part made in three, with nine book fhelves in ditto, fram’d backs and fall plinth ~55° EXTRAS. Each inch in length, more or lefs - - - - o Ditto in height - -- -- -- -o i 6 o 8 Each [ 48 ] Each inch, more or lefs in the height of middle ends, either top or bottom carcafe Making the lower part in three carcafes - Each joint in the upper outfide ends - Each joint in the lower outfide ends - - - - Joints of the infide ends not to be paid for. Veneering each end - - - - - - Each joint in the veneer of upper ends - Ditto in the veneer of lower ends - Veneering door frames long-way, each pair - Ditto crofs-way on the upper frames, each pair extra Ditto crofs-way on the lower frames, each pair extra Veneering each pannel in bottom part - Each joint in the veneer of ditto - Veneering each pannel for top part - Each joint in ditto ------ Veneering the top long- way - Ditto crofs-way, each joint _____ Veneering the breaks of middle carcafes, each break Each extra drawer in the wings, cock beaded - Each infide drawer ------ Each partition - -- -- -- - Lining ditto crofs-way, each - When drawers in the center part as above, dedudt for doors Ditto lor each fhelf ------- Each long drawer in the center part - Each partition -------- Each long drawer within the doors of middle part, fcratch beaded Each joint in drawer fronts or pannels, either folid or to veneer on - £■ d - 0 O 6 O30 0 0 2 001 OlO OO4 003 0 2 0 Ol6 OlO OO 9 00 6 010 00 6 010 002 004 023 020 006 o o 1 060 o 1 6 02 6 006 023 o o 1 Slipping [ 49 ] Slipping drawer Tides and plowing bottoms in, each drawer Munting in bottoms, each — - — — — Half ditto under the bottom — — — — — Veneering each long drawer front — — — — Ditto each fhort — - — - — — — — — Each butt joint in the veneer - - - — — Veneering partition edges afkew or crofs-way, per foot extra For the price of extra work in fhelves, See. — • See Clothes Pre/s. An upright partition in the upper middle part, plain groov’d on both tides — — — — — — — Ditto in the lower part - — — - — — For the price of any other fort of grooving or extra fhelves — See Bookcafe. A loofe frame for the plinth — — — — — Veneering the plinth long-way, per foot in length — — Ditto crofs-way, per joint — — — - — A loofe frame for the furbafe moulding — — — A veneer’d frieze below the furbafe moulding, with an aftragal at foot, per foot — — — — — Veneering the frieze under the cornice, with aftragal at the foot, or putting in quarter fluff for fluting, per foot in length -------- For the price of Gothic cornice, dentil, or fafeia— *-See Tabic of ditto. An affragal round the front and ends of lower part, when a drawer above the doors, per foot in length — — No extra carcafes more than three in each part to be charg’d for, only add for each extra door - - - - If fram’d backs to extra carcafes, each pannel - - £. s. d. 003 003 o o if 008 00 6 004 o o of 030 020 030 0 o lf 001 030 O O 2i OO 4 o o if The H O O CO O [ 5 ° 3 The top and bottom part of this library, as firft defcribed, £, s. d. confidered of equal value when divided for the work- men, and all extras may be added to each part fepa- rate ; the bottom part to Hart in that cafe three feet high. If bead and butt pannel, each pannel - - - -003 Oiling and polifhing, at per foot in length - - -00 6 A STRAIGHT-FRONT CABINET, Four feet long, five feet high to the top of the cornice, in two carcafes, two inner ends and four flat-pannel’d doors to the upper part, pannels plow’d in, two ditto to the wings of the lower part, and one drawer in the center, the lower ends fourteen inches wide, the upper ends feven inches, on taper flump feet — - - 3 5 o EXTRAS. Each inch, more or lefs, in length - — Ditto, in width of ends of each carcafe - Ditto in height _____ Plain grooving the ends for fhelves, each fide For the price of extra grooving — See Bookcafe. If the infide is fitted up with fmall drawers, Counting-houfe Bookcafe. Each fhelf in the upper part _ _ _ Ditto in the lower part _ - - — When - -010 -003 - -004 - -006 &c. — See -005 - -006 £• s - d - [ 5> ] When no door to the wings, dedudt for door and cleaning cupboard, each — — — - — - -o Each drawer in the wings — — — — — O Each partition — — — - — - -o Each extra drawer in the center - - - - O Each partition — — — — — — — O Lining ditto crofs-way, each — — — — — o Slipping drawer (ides and plowing bottoms in, each drawer o Glueing up ends, drawer fronts, or pannels, either folid or to veneer on, at per joint — — — — — O Veneering each drawer front in the wings — — — o Ditto in the center part - — - — o Each butt joint in the veneer — - — - — o Veneering partition edges afkew or crofs-way, per foot extra o Veneering the ends, each / u PP er l lower — — — o Veneering the door frames long-way, each pair - - o Ditto crofs-way - — — — — o Veneering the pannels, each — — - — — o Each joint in the veneer, per foot in length — — — o Framing the ends of the wings - — — — o Lining up ditto to guide the drawers - — - - o For the price of pilafters, and breaking mouldings round ditto — See Straight-front Library. Veneering the frieze, with an aftragal at foot, per foot — o Fram’d backs, each pannel - - - - - o For the price of arch — See No. 1 Celleret Sideboard. For the price of banding, See. — See Tables of ditto. Oiling and polifhing, at per foot in length - - — o 4 o 2 O ° 5 2 3 o 6 O 1 ° 3 o 1 ° 3 o 6 o 4 o oj- o 6 o 8 2 o 3 6 o 8 0 2 6 o 1 o O 3 o 6 o 6 H 2 A CY- [ 52 3 A CYLINDER-FALL WRITING TABLE, Three feet long, two drawers in front, cock beaded, three £. s. fmall drawers, three fham ditto, and fix letter holes in- fide, the edge of the top and fweeppart of ends moulded, the cylinder veneer’d, and an aftragal round the bottom of the frame - - - - - — — — 211 EXTRAS. Each inch, more or lefs, in length - - - -00 Two fhort drawers under ditto to form a knee hole, drawers and extra framing - - - - - -07 Slipping drawer fides and plowing bottoms in, each drawer o o Munting in drawer bottom - - - — —00 Half ditto under the bottom - - — — — o O A plain arch, with a cock bead or firing - - —01 For extra work in ditto — See Celleret Sideboard , No. 1. Veneering long drawer front — — — - —00 Ditto each fhort — — — — — — — 00 Each butt joint in the veneer — — — - —00 Veneering the top — — — — — — — 00 Ditto the ends, each - — — — — — 00 Ditto, when a knee hole — — — — - — 00 Each corner firing round the top, per foot — - —00 Corner firing round the cylinder or ends, per foot - -00 Hollow and two beads or fione moulding on the front of fianding board, and continued on the ends — —01 If continued on the back, extra - - - -00 Veneering ditto crofs-way, with a firing on each fide, at per foot d. o 9 6 3 3 3 6 4 4 8 6 8 1 1 o 3 003 A fmall [ 53 1 £. s. d. A fmall aflragal or bead at the lower edge of the {landing board, and continued on the ends ____ Veneering the frieze crofs-way, at per foot — — — Each flider in the ends, fquare clamp’d — - — Making the {landing board to Aide — - — — A Aap in ditto, fquare clamp’d, lip’d, or crofs bands — A horfe to ditto — — — — — — A bottom under ditto _______ Veneering the Aider for cloth to be fet againft cleaning up, when folid. Lining the Aider with cloth _ _ _ _ _ Ditto, when a flap - — — — — - — Veneering a plain Aider _ — — Ditto the framing, when a flap — _ _ _ Fixing two pieces on the Ades of Aide, fcollop’d in front, to form a tray For the price of extra work in Aider — See Dr effing Chef. Fixing the legs with iron fquares, or fcrews and plates — A plain cove in front to fliam a drawer above the fall — Each extra {ham, with a Aring — - — — - A drawer in ditto the whole length _ _ — _ Each extra drawer in the length — _ _ — Making the fall to work with tambour, extra — — Making the fall to work with No. 1. Irons, as in plate — Ditto No. 2, and filling up the inflde for ditto — — Making the Aider to draw out with lopers - _ _ For the price of extra work inflde — See Secretary Drawer. Sawing out each leg ______ For the price of crofs-banding, extra work in legs, &c. — See Tables of ditto. Oiling and polifhing ______ o ° 9 O O 1 o i 6- o 1 o 0 2 0 O 1 o o o 6 009 010 0010 010 009 026 050 004 030 023 060 050 0100 030 001 010 A CY- [ 54 ] A CYLINDER-FALL DESK, £ Three feet long, three drawers in front, cock beaded, three fmall drawers, three fliam ditto, and fix letter holes infide, the edge of the top and fweep part of the ends moulded, the cylinder veneer’d, ftanding board made to fiide, on plinth or common brackets - — —3 EXTRAS. Each inch, more or lefs, in length - — _ - - Each extra long drawer — — — — — — Each partition — — — — — — — If two fhort drawers in place of a long one, extra - Each joint in the ends, top, or drawer fronts, either folid or to veneer on, at per joint — — — — — Veneering each long drawer front - — - - Ditto each fhort — — — — — — — Each butt joint in the veneer — — — — — Veneering the ends, each — — — — - Each joint in the veneer — — — — — — Fram’d back, each pannel — — - — — Munting in a plain back — - — — - — For the price of extra work in the carcafe — See DreJJing Chejl. For the price of work not inferted here — See Cylinder -fall Table . o o o o o o o o o o o o s. d. 3 o o 10 2 3 0 6 1 9 o 1 o 6 o 4 0 4 1 o O 3 o 6 o 3 No. 1. [ 55 3 No. I. TAMBOUR WRITING TABLE, £. s. d. Three feet long, two drawers in front, cock beaded, the edge of the top and fweep part of the ends moulded or veneer’d crofs-way, plain taper legs, and anaftragal round the bottom of the frame — - — - -180 EXTRAS. Each inch, more or lefs, in length — — — — A cafe for the infide work - — - - — Each drawer in ditto, including partitions — — — Each letter hole in ditto — — — — — — Each plain arch - — — — — - — For the price of any extra work in ditto — See Secretary Drawer. Making the ftanding board to Hide — — — — Fixing a piece to the back edge of the ftanding board to fham three drawers — — — — — — For the price of extra work in Aider — See Cylinder-fall Writing Table. An aftragal round the front and ends of the carcafe to break the joint — — — — — — — If continued on the back, extra — — — — A hollow and two beads or ftone moulding on the edge of the ftanding board, and continued on the ends of the carcafe, or veneer’d crofs-way, with a firing on one edge If a firing on both edges, to be - - - - O o o o o o o o o o o 0 9 2 O 1 o o 3 o 1 1 o 1 o 1 o O 3 1 o 1 6 For [ 56 ] ^ . s. d. For the price of extra work — See Cylinder-fall Writing Table. Oiling and polifhing - - - — — -OlO C <>0>0*©0 No. II. TAMBOUR WRITING TABLE, Three feet long, two feet two inches wide, reeds from front to back, two drawers in front, cock beaded, two fham ditto on the back, the edge of the ends moulded or veneer’d crofs-way, an inner lock fixed to the ftanding board, plain taper legs, and anaftragal round the bottom of the frame - - - — — - -196 EXTRAS. Each inch, more or lefs, in length — — — — o Ditto in width ------ -o Each corner firing round the fweep part of the ends — o Veneering the ftanding board for cloth, fet againfi cleaning up, when folid. A cafe for the infide to receive drawers - - - o Each drawer in ditto, including partition — — - o Each letter hole — — — — — — — o Each plain arch — — — — _ — _o For the price of extra work in ditto — See Secretary Drawer. For the price of other work not inferted — See Cylinder- fall Writing Table. Oiling and polifhing — — — — — — o 0 9 o 6 0 3 2 o 1 o 0 3 o 1 1 o A TAMBOUR [ 57 ] A TAMBOUR DESK. £■ s. d. Three feet long, four long drawers in front, cock beaded, {landing board made to Hide, three fmall drawers, three {ham ditto, and fix letter holes infide, the edge of the top and fweep part of the ends moulded or veneer’d crofs- way, with a firing in one corner, faft plinth or common brackets - - - — - - - - 280 EXTRAS. Each inch, more or lefs, in length - - - ~ o l o If two fiiort drawers in place of a long one, extra — -020 For the price of extra work — See Cylinder-fall Dejk and Table. Oiling and polifiiing - - - - - — 010 C h©©)*©*©*© 1 *©**© ©-><3* “O' a A LIBRARY WRITING TABLE, With Tambour Top, Three feet fix inches long, two feet fix inches wide, in three carcafes, one long and fix fhort drawers in front, cock beaded, reeds from front to back, the fweep part of the ends and edge of the fianding board moulded or veneer’d crofs-way, with a firing in one corner, anaftragal round the upper carcafe to break the joint, on faft plinth 36c EXTRAS. 1 [ 5« ] EXTRAS. Each inch, more or lefs, in length or width — — — Each extra long drawer — — — — Each fhort drawer, more or lefs - - - - Each long partition, more or lefs - — - - Each fhort ditto ------- Lining ditto crofs-way, each — — — - — Veneering each long drawer front, or fham ditto - - Ditto each fhort — — — - — For the price of fham drawers by firing or bead — See Table of ditto. Veneering partition edges afkew or crofs-way , at per foot extra Ditto with king, tulip, or any other hard wood, at per foot extra ________ Veneering the upper part of the back - — - _ Ditto each wing - — — Veneering the back of the wings to reprefent doors, each Ditto each frame long- way _____ Ditto the framing crofs-way, each frame extra - — Veneering the plinth long-way, per foot _ _ _ Ditto crofs-way — For the price of extra work on doors — See Table of ditto. Each cupboard in the wings, with a flat pannel’d door, the pannel plow’d in ______ A cafe for the infide of cupboard _ — _ _ For the price of work infide ditto — See Counting-houfe Bookcafe. Each flider in the ends, fquare clamp’d _ _ _ £. s. d. 0 1 o 026 020 006 005 001 008 004 0 O Oj 001 006 009 006 009 00 6 001^ 002 0 4 9 016 020 For i 59 3 £■ For the price of extra work in ditto — See Dreffing Chejl. - o - o - o - o If the tambour lifts up from each front, and turns down under a flat top in the middle, extra - - - o Veneering the top — — — — — — ~o Each cafe for infide work - - — — - o For the price of drawers, &c. — See Secretary Drawer. If made with a top as Tambour Defk, without infide, dedudt o Each door over the drawers in the wings, or in the knee hole, with a flat pannel, the pannel plow’d in — - o A frame to receive the door in the knee hole — — o Each extra miter in the plinth, when a door in the knee hole — — — — — — — — q A bottom to the cupboard — — — — - o Oiling and polilhing, when a Angle front - - - o Ditto, when a double front — - - — — o Veneering each lower end - Ditto upper ends, each \ out ^ e [ infide Each joint in the veneer — - s. d. o 10 o 8 o 6 ° 3 4 o 0 8 2 O 5 o 3 o 1 o o 2 0 6 1 3 1 9 TOPS FOR TAMBOUR OR CYLINDER-FALL WRITING TABLES. A SOLID TOP, three feet long, three inches and a half high, one drawer in ditto, the top lap dovetail’d down, a moulding on the front and ends of the bottom - -050 If two drawers in the length - - - _ _ 0 6 ‘j If three drawers in the length - - - _ _ 0 7 g 1 2 Each \ [ 6'o ] Each extra inch in length, more or lefs — — - Ditto in height Each extra long drawer — — — — — — Each partition _______ If two extra drawers in the length _ _ _ - If three ditto _______ An aflragal or flone moulding on the front and ends of top Ditto on the back, top, or bottom moulding, extra - Veneering the top _______ Ditto long drawer fronts, each _ _ — — _ Ditto fhort drawer fronts, each - — — - - Veneering the back ______ Ditto the ends, each ______ Veneering partition edges afkew or crofs-way, per foot extra Ditto with king, tulip, or any other hard wood, at per foot If the above is made with cove front, when one drawer, extra Each extra drawer in a cove front, extra from flraight — If the ends of the carcafe are cov’d, extra - _ — Veneering long drawer in cov’d front - - — — Ditto crofs-way _______ When two or more drawers in length, each — — — Ditto crofs-way, each ______ Veneering each end ______ Ditto crofs-way _______ Corner firing, per foot ______ Oiling and polifhing ______ £■ s. d. O 0 2 O 0 2 O 2 0 O O 4 O 3 3 O 4 6 O 0 9 O 0 4 O 0 6 0 0 4 O 0 3 0 0 3 0 0 2 0 0 °! 0 0 1 0 2 0 0 0 6 0 1 6 0 1 0 0 1 6 0 0 8 0 1 0 0 0 6 0 0 8 0 0 1 0 0 4 A TOP, as in plate 13, fig. 1 , right-hand end, three drawers in ditto, veneer’d top, folid front, plain back, and cock beaded or firing _______ 1 4 c Each [ 6 1 ] £■ 5 - d - Each extra drawer with fquare ends - - - -013 Each extra partition - - — - - — 004 Making either end of drawer front to fit the fweep of ends 006 Veneering the front — — — — — — 016 Ditto the back — — — — — — — 008 Veneering partition edges afkew or crofs-way, per foot extra O O Oj Ditto with king, tulip, or any other hard wood, at per foot 001 For the price of glafs frame and flandards — - See Drejfmg-box Glajs. Oiling and polifhing — — - — *- — 004 A TOP, as in plate 14, fig. 2, right-hand end, feven drawers in ditto, the top veneer’d, front and ends folid, plain back _______ Each extra drawer with fquare ends - - - - Making either end of drawer front to fit the fweep of ends Veneering the front ______ Ditto the back _______ Ditto the ends, each - — — — — — Oiling and polifhing ______ 1 o o o o o o 10 1 o 2 O o o o 3 6 o 9 2 4 C >0'0*2*<^> 5 0*©*Gx > <3 v >0«0< o No. I. A LIBRARY WRITING TABLE, Four feet long, two feet fix inches wide, three drawers in front, cock beaded, plain back, framing fix inches deep, plain Marlbro’ legs - - - - _ -0180 EXTRAS. [ 62 ] EXTRAS. ' l . • . . . ' • Each inch longer or wider, more or lefs - - - Each Aider in the ends, fquare clamp’d - - Glueing up the top, either folid or to veneer on, at per joint Mitering Huff for a moulding round the top - — — Clamping the top end- way to appear as folid - - Glueing up top, each joint — - - - - Framing the top, with two pannels - - - . — Each extra pannel — - — — Lipping the top for cloth, to be let againft cleaning up a folid top. Lining the top with cloth — — — — — Ditto with leather - — — _ _ — _ Veneering the top, at per foot in length - - - Each joint in the veneer of ditto — - — — If a long drawer is introduced in place of three fliort ones, dedud: - - - _ _ - — — When ditto is made with double front to draw out either way, extra - — — - - — — A long drawer in the back — — — — — Each fliort drawer, more or lefs, in back or front — — Slipping drawer fides and plowing bottoms in, each drawer Veneering long drawer front — - — — - Ditto each fliort — — — — — — — Each butt joint in the veneer — — — — — Veneering partition edges afkew or crofs-way, at per foot extra — — — — — Ditto with king, tulip, or any other hard wood, at per foot Veneering the end rails, each — - — — — Aftragal round the bottom of the frame — — - £. s. d. 004 026 O O l\ 010 OOIO O o 1 } 0 2 0 00 9 010 Ol6 OO4 o o 6 0 3 9 030 026 020 003 008 004 004 0 o o± 001 004 016 If C 63 1 If made with a knee hole, when one front, for extra framing Ditto* when double front — — An aftragal round the frame, when a knee hole - - A plain arch in the knee hole, with cock bead or corner firing For the price of extra work in ditto — See Celleret Side- board, No. 1. Sawing out the legs, each - — — — — “ Tapering ditto, each fide — — — — — For the price of extra work in legs — See Tables of ditto. Oiling and polifhing, when the top is lin’d — — — Ditto, when the top is folid or veneer’d — — - £. s. d. 030 036 024 o 1 3 000 000 009 010 C <0»0 > 0*0*<2>»0 fl <2x*0«0 , '0 O No. II. A KNEE-HOLE LIBRARY WRITING TABLE, Four feet long, two feet fix inches wide, nine drawers in front, cock beaded, afiragal or ftone moulding on the edge of the top, on fafi plinth or common brackets 250 EXTRAS. Each inch, more or lefs, in length or width - Ditto with double front ------ Making ditto in three carcafes — «- — If faften’d together with iron plates, putting on each plate Each drawer, more or lefs - - - — Each partition - 00 9 010 026 002 020 ° ° . 5 Lining Ml" -Ww C 64 ] £■ 1 ' : ; iv, each — — — — o . , .1 lies, and plowing bottoms in, each drawer o ig up ends or drawer fronts, either folid or to veneer on, at per joint __.--_.-o Ditto the top - O For any ext rework in top — See No. 1. Veneering drawer fronts, each - - - - - o Veneering partition edges afkew or crofs-way, at per foot extra --------- Ditto with king, tulip, or any other hard wood, at per foot Veneering the ends, each - - Each joint in the veneer ______ Framing the ends with one flat pannel, each end Each extra pannel ------ Veneering the back of the wings, each - Ditto the plinth long-way, per foot - Ditto crofs-way ------- Veneering back of wings to reprefent doors, each pannel Ditto each frame long-way - Ditto the framing crofs-way, each frame extra For the price of extra work on doors — See Table of ditto. Each cupboard in the wings, with a flat-pannel’d door, the pannel plow’d in - -- -- -- A cafe for the infide of the cupboard - For the price of work infide ditto — See Counting-houfe Bookcafe. An aftragal round a fingle front - Ditto, when a double front If the top is fram’d as the Aider of a tambour table, and a flap with a horfe and bottom to ditto - - - o o o o o o o o o o o o o o o o o s . d . o 1 O 3 o 1 o lj 0 5 o o|- 0 1 1 o ° 3 2 o 1 o O 9 O 1 # O 2 o 6 o 9 o 6 4 9 1 6 1 2 1 6 5 0 A flap [ 6 5 ] £■ *■ d - A flap, one foot fix inches long, five inches wide, fupported by a brafs flay, the back part of the top cut to receive the fame - - - - - - - 020 A flap, hing’d to the back part of the top, with a rule joint, fupported "by two lopers - - - - - -040 If three-quarter fluff is miter’d round on the flat of the top, with a hollow under the outer edge of ditto, and an extra folid top hing’d in front, fupported with a horfe behind - - - - - - - - o 6 6 If the ends and front rails are rabbited, and a thin top fitted in to ditto, with a hollow miter’d round the infide, (as in {having fland) and an extra folid top hing’d in front, fupported by a horfe behind - - - -070 A lipping to cover the joint of the hollow - - -010 A fquare frame in addition to the above, the whole fize of the top, and an extra horfe to make a double rife, extra 046 Working a hollow on the edge of ditto - - -009 Brafs fteps, and the feet of the horfe tip’d with ditto, extra 00 6 Oiling and polifhing, when a fingle front - - -010 Ditto, when a double front - - - - - 016 K No. III. [ 66 ] No. III. A SERPENTINE KNEE-HOLE LIBRARY WRITING TABLE, £■ Four feet long, two feet fix inches wide, nine drawers in front, cock beaded, an aflragal or fione moulding on the edge of the top, on fall plinth - 3 EXTRAS. Each inch, more or lefs, in length or width - - - o Ditto, with double front ------ O Making ditto in three carcafes - - - - - o Each drawer, more or lefs - - - - - o Each partition - -- -- »- -o Lining ditto crofs-way, each - - - - - o Veneering drawer fronts, each - - - O Veneering partition edges afkew or crofs-way, per foot extra o Ditto with king, tulip, or any other hard wood, at per foot o Sweeping the ends half ferpentine, and plain veneering ditto o When both fronts are made ferpentine, with three drawers in the length, and a cupboard in each wing of one front, the other front as in the preamble, extra - - - o Sweeping the ends ferpentine, plain veneer’d - - o For the price of canted comers or columns — See Serpentine DreJJing Chejt. s. d. 6 o 1 o 1 3 3 0 2 9 o 6 o 1 o 7 o o^- o 1 10 6 18 o 15 o An [ 67 ] £■ s - d ■ An aftragal on the front and ends of the carcafe, when the ends are ftraight ------- Ditto, when the ends are half ferpentine - Ditto, when a double front and ftraight ends Ditto, when ferpentine ends - Each extra miter, when canted corners - Sawing drawer fronts out of two-inch fluff, each cut Ditto three-inch fluff ------ Glueing up ditto, at per joint - For the price of extra work — See No. 2. Oiling and polifhing, when a Angle front - Ditto, when a double front - 018 023 026 030 000 000 000 001 012 018 C <2>^3>*0->0>0 < 0>OxS>‘0'<3> 3 A CIRCULAR LIBRARY WRITING TABLE, Three feet Ax inches diameter, four drawers in ditto to run in fquare, and four fham ditto, cock beaded, the top to turn round on a pillar and three claws, and faf- ten’d to ditto by a wedge through the top of the pilldr ; claws as No. 1, Plate of ditto - - - -1120 EXTRAS. Each inch, more or lefs, in diameter, up to four feet Each inch above four feet in ditto Glueing up the top or bottom, at per joint Rounding the edge of the top - Veneering the edge of ditto, per foot k 2 008 0010 001 00 6 o o l| Comer 4»|w to|-i [ 68 ] Corner firings round ditto, per foot — — — — Aftragal or hone moulding on the edge of the top, per foot Banding the top for cloth to be fet againft cleaning up. A firing between the band and cloth, at per foot — — Lining the top with cloth — — — — — Ditto with leather — — — — — — — Framing the top or bottom, with four fquare pannels — Ditto, when fram’d flufh on both fides, extra — - Each, extra fquare pannel flufh on one fide — — — If the pannels are fram’d bevel, each pannel extra from fquare, when the framing tends to the center — — An aftragal round the bottom of the carcafe, at per foot — If made with angle drawers in place of fham ditto, deduct for each fham drawer — — — — — — Deduct for each drawer that runs in fquare — — — Each angle drawer - — — — — - — Guide to each drawer — — — — — — Each upright partition to center — — — - Each quadrant drawer’ — — — — — — Glueing up ditto, each joint — — — — — Veneering drawer fronts, or fham ditto, each — — Sawing drawer fronts out of two-inch fluff, each cut - If crofs-way, each joint extra — — — - — Each extra claw _______ For the price of other forts of claws — See Table of ditto. A pedeftal, fixteen inches fquare, a door to ditto hing’d on the miter, one fix’d fhelf infide, on faft plinth, extra from pillar and claws _______ Fixing the top to ditto, with a center pin, four rollers, and a ring for ditto to run upon — _ _ _ _ Clamping the door, fquare clamps - - - — £■ s. di O 0 1. O 0 . 2 0 0 0 | o 1 0 0 ] 6 o 3 o o 1 o 0 o 9 o o 9 Q o 2 O 0 8 O 2 3 0 3 o o. c. 4 o 0 6 o 4 O' o 0 l o o. 6 0 0 of o o l 0 1 6 0 5 6 o 2 o 0 0 6 Miter [ 69 ] £■ Miter clamping ditto, each miter extra — _ - o Veneering the pedeftal, each fide — — — — o Each drawer infide the door, fcratch beaded — — o Each partition in pedeftal — — - — — o Lining ditto crofs-way, each — - — — — O If three drawers in front, (in place of door) and partitions to ditto, extra — — — — — — — o Each extra drawer — — — — — o Veneering drawer fronts, each - — - — - — o A partition edge above each real drawer in the top part — o For any extra work — See Pedejtal , with Vafe. If this table is made oval, to be extra — — — o A circular well hole, with hing’d flap and crofs bands round ditto, when the top is folid or glued up, including the faflening — — — — — — — — o Ditto, when the top is fram’d, extra — — — — o An oval ditto, extra ------ o Oiling and polifhing, when on pillar and claws - - o Ditto, when a pedeflal - — — - - - — o s. d. o 6 0 6 1 8 ° 5 o 1 4 o 2 O o 4 ° 3 4 o 5 ° 1 o 1 o 0 8 1 o No. I. A KIDNEY LIBRARY WRITING TABLE, Three feet fix inches long, one foot eight inches wide in the middle, framing four inches deep, the rail veneer’d, four plain Marlbro’ legs, top fhaped as in Plate 5. fig. 2. o 18 o EXTRAS. [ 7 ° 1 EXTRAS. £. s. Each inch longer or wider - - - - - o o When a drawer in ditto - - - - - - oo Ditto in depth of framing - - - - - o o A long drawer in front - - — - — ~ ° 5 If three ditto in length — - - — - - 09 Each drawer in the end — — — — — — 03 Glueing up the top, either folid or to veneer on, at per joint o o Veneering the top - - - — - - - 01 Each joint in the veneer, per foot in length — — - o O If made without breaks, dedudl: - — - -03 An aftragal or ft one moulding on the edge of the top, per foot - - - - — - - — 00 Veneering the edge crofs-way, at per foot — — — o o Corner firings on the top, at per foot — — — — o o Lining ditto with cloth - — — — — - 01 Ditto with leather — — — — — — — 01 Framing the top, with a flap, horfe, and bottom — —04 Lipping the top and flap for cloth fet againft cleaning up. Lining the flap with cloth — — - — -00 An aftragal round the bottom of the frame, when the legs are flufti, at per foot in length — - - —00 Each miter in ditto, extra — — — - -00 Sawing out each leg — — — - - —00 Tapering ditto, each fide - ~ - - -00 For the price of extra work in legs — See Table of ditto. Oiling and polifhing, when the top is lin’d — — — o O Ditto, when the top is folid - - - - - o o d. 3 4 8 o 0 6 1 3 2 0 1 O 6 6 3 2y °i 6 9 No. II. [ 7i ] No. II. A KNEE-HOLE KIDNEY LIBRARY WRITING TABLE, as in Plate 5 , Fig. 2. £. s. d. Four feet long, two feet wide in the middle, veneer’d front and ends, four drawers in each wing, and one ditto above the knee hole, cock beaded, an aftragal round the bottom of the carcafe, eight plain pilafters, and taper flump feet 415 o EXTRAS. Each inch, more or lefs, in length - - — - 0 1 0 Ditto in width — - - - — — — O 0 6 Making ditto in three carcafes — — — — — O 3 0 An aftragal to break the joint of the carcafes, per foot — O 0 2i Each miter — — — — — _ _ — O 0 Working an aftragal or flone moulding on the edge of the top, per foot - - - - — - - O 0 2i Lining up the top - - - - - - - O 2 O Veneering the top — — — — - - — 0 1 6 For the price of glueing up the top, &c. — See No. 1 . Each drawer, more or lefs — — — - — 0 3 6 Each partition - - - — - — — 0 0 6 Lining ditto crofs-way, each — — — - — 0 0 1 Sawing drawer fronts out of two-inch fluff, each cut — 0 0 Glueing up ditto, each joint - - ~ — — 0 0 1 Veneering w|' E 7 2 3 Veneering partition edges afkew or crofs-way, per foot extra Ditto with king, tulip, or any other hard wood, at per foot A frieze under the top moulding, veneer’d crofs-way, with an aftragal at foot, per foot in length - - - A veneer’d plinth round the bottom, extra from flump feet If broke round the pilafters, each miter - - - Each fham door on the wings, the framing veneer’d long- Ditto crofs-way, extra ______ Each cupboard in the wings _ _ _ _ _ Ditto in the back _______ Dedudt for drawers and partitions as above. A cafe for the infide of cupboard _ _ _ _ For the price of work in ditto — See Counting-houJ e Book- cafe. Hinging part of the flap to a part of the front moulding, to make a book-reft ______ A Aiding frame to ditto, to run both ways — — — Making the flap to rife with four ftems, as fhewn in plate, with four racks and fprings — — _ - — For the price of Aider in drawer or lopers — See Furniture Drawer. For the price of crofs banding, Sc c. — See Tables of ditto. Oiling and polifliing ______ £. s. d. O o o\ O O 1 o o 41- 040 0 0 2 OlO 0 0 8 060 070 0 2 0 Ol 6 O 3 6 o 10 6 020 A GENTLEMAN’S [ 73 1 A GENTLEMAN’S WRITING TABLE, as in Plate 4, Five feet long, two feet nine inches wide, made as either £. s. d. end, a cupboard in each hollow part, veneer’d front and top, the back veneer’d crofs-way, on plain taper legs - 8 O O EXTRAS. Each inch, more or lefs, in length or width - - Veneering partition edges aikew or crofs-way, per foot extra Ditto with king, tulip, or any other hard wood, at per foot A front edge under the top moulding over drawers and doors — — — — — — — — Glueing Huff for a moulding round the Handing board — Lipping the Handing board for cloth, to be fet againfl cleaning up, when folid A flap, horfe, and bottom in ditto, and the Handing board fram’d to receive ditto — — — — — — If the top moulding is continued down the fweep part, when made as right-hand end — — — — Making part of the top of the wings or back to rife, framed, with a horfe and bottom to ditto, each - - If the bead A. is omitted in the top moulding, dedud — If no top moulding, dedud from Hart price — — If the hollow B. is omitted, dedud — — - — If the beads C. and D. are omitted, dedud — - — If the table is made fquare, with the above mouldings omitted, dedud from the Hart price - - Sawing out each leg ______ L 010 0 o o| 001 018 020 046 036 046 016 0 6 6 050 026 2140 001 Socket [ 74 ] jf • S 4 d 4 Socket caftors — — — — — — — o o 6 For the price of crofs-banding, extra work in legs, See . — See Tables of ditto. Oiling and polilhing — — — — — — 023 A WRITING TABLE, as in Plate 6, Fig . 1 , Three feet long, two feet wide, the drawer front to re- prefent two, the top one to turn down, fupported by quadrants, a cafe and fix drawers in the upper part of the infide to Aide as a clothes-prefs fhelf, the fpace below empty, plain taper legs, and an aftragal round the bottom of the frame, a ftone moulding round the edge of the top, or the edge veneer’d, and a firing in the upper corner — — - — — — — - 226 EXTRAS. Each inch, more or lefs, in length — — - Ditto in width — — — Glueing up the top either folid or to veneer on, at per joint Clamping the top long or end-way — — — Miter clamping ditto, each miter extra - - Veneering the top, per fuperficial foot - - Each joint in the veneer, per foot in length - — Veneering the front ______ Each butt joint in the veneer - - _ — 006 004 001 006 00 6 002 002 010 004 Veneering [ 75 J L • J * d’ Veneering the end rails, each — — - — — 004 Ditto the back rail — — — — — — 006 Making the frame to form a knee hole, and the front of the drawer to (ham two fhort ditto under the upper front, with a plain arch in center, cock beaded — — —050 For the price of extra work in ditto — See No. 1. Celleret Sideboard. For the price of extra work inftde — See Secretary and Furniture Drawers. Sawing out each leg — — — — — — 001 Oiling and polifhing - — — — — — OOlO A RISING-TOP WRITING TABLE, Two feet long, one foot four inches wide, framing four inches deep, one drawer in ditto, cock beaded, the top fupported by a horfe, plain taper legs, an aftragal round the bottom of the frame, aftragal or ftone moulding on the edge of the top, or the edges crofs banded, and a firing in the upper corner — — - — - o 96 EXTRAS. Each inch, more or lefs, in length or width - Ditto in depth of framing — - — Each extra long drawer, cock beaded — — Ditto fhort drawer — — — — - Fitting up the drawer for ink, fand, and wafers l 2 -003 -002 -019 -016 -006 Veneering O [ 7 $ ]• Veneering each long drawer front flraight-way - Ditto each fliort drawer - — - — - Ditto each end or back rail _ _ — — If crofs-way, each joint extra — — — — Glueing up the top, at per joint - - - Square clamping ditto — — — — - Miter clamping ditto, each miter extra - - Mitering fluff for a moulding round the top - - A firing in the lower corner of the top, per foot — Framing the top with one pannel — — — Lipping the top for cloth to be let againfl cleaning up. Lining the top with cloth — — — — Ditto with leather — — — — — — Each flider in the ends, fquare clamp’d — — A frame under the top, and an extra horfe to make a double rife — — — - — — — 02 A book refl, w r ith pins and fockets - — — —00 Each inch longer, when a double rife - - — —00 A hollow fhelf with ledge grooved in ditto - — -02 Three low rails framed in the legs, with aflragalon the top edge of ditto, and a hollow fhelf — — —03) For the price of extra work in legs — Set Table of ditto. Oiling and polilhing - - — - - - 001 £. s. d. -003 -002 - 0 0 3 -001 -001 -00 6 -006 - o o fr -001 - o o ( - 00 / - o o ( -01 A LAD *s [ 77 I A LADY’s SCREEN WRITING TABLE, O; foot eight inches long, one foot four inches wide, fra- £. lg four inches deep, one drawer in ditto, cock beaded, ai agal or flone moulding on the edge of the top, or the ec e veneer’d, and a firing in the upper corner, the fc en to flide in a groove through the top between the b; k legs, plain taper legs, and an aflragal round the bctom of the frame — — — — — — o EXTRAS. Eacl inch, more or lefs, in length or width - - o Dittc in depth of framing - — — — — o Eacl extra long drawer, cock beaded — — — o Fittig up the drawer for ink, fand, and wafers - — o Eacl plain flider - -- -- -- o Lipp ig the top for cloth fet againfl cleaning up. Vene ring the top - -- — _-_o Linii^ ditto with cloth - — — — — - o Dittc with leather — — — — ___o Vene ring the fronts, &c . — See Rifmg-top Writing Table. Oilir. and polifhing s » d . 10 6 ° 3 0 2 1 9 0 6 1 3 o 6 o 4 o 6 o 4 A LADY’s [ 78 ] A LADY’s WRITING FIRE SCREEN, as in Plate 6, Fig . 2, One foot eight inches long, the flandards three inches wide, £ the corners fquare, flap to fall down, with joint flays to write upon, fquare clamp’d, or a {training frame, with a bead miter’d round, plain back, claws as No. 1 in plate of ditto — — — — — — — — o EXTRAS. Each inch, more or lefs, in length or width — — o A flap hing’d to the top, fquare clamp’d, with horfe to ditto for reading, to be the fame as writing flap, with joint flays. Making the reading part to rife with part of the top, and a frame behind for the horfe to refl in — — — o An ovalo or bead on the corners of the top and ftandards, either infide or outflde — — — — — — o Each corner firing on the flandards or rails, per foot — o A flielf, hing’d and fupported by two SS — — — o A fix’d cafe, fitted up for ink, fand, pens, and wafers — o A hollow ditto for the pens — — — — — o A paper cafe made to lift out, with front, back, and one partition with fcollop edges — — — — — O A plain fhelf infide, with a rim on the front — — — O Scolloping the edge of the rim — - - — o When made with a reading flap and horfe on one fide, and a writing flap to turn down on the other, with an inner back to ditto, extra — — — — — — o Miter clamping the flaps, each miter extra - - - o s. d . 15 o o 2 3 0 o 6 o 1 0 9 1 3 o 4 2 6 o 6 o 2 3 6 o 6 Veneering [ 79 ] Veneering the flaps, each fide — — — — Ditto the ftandards, each fide — — — — Ditto each edge of ditto — — — — — Veneering the rails, each fide — — — — Ditto each edge of ditto — — — — — Framing the flaps with one pannel, each flap - Making ditto with two flat-pannelM doors below, and plain back, extra — — — — — Framing the back with two pannels to match the doors Veneering the door frames long- way, each pair — Ditto crofs-way, extra — — — — — Veneering each pannel — — — — — Lining the flap with cloth — — — — For the price of crofs-banding, &c. — See Table of ditto. Oiling and polifhing — - — — — Ditto, when doors at the bottom part - - £. s. d. -006 -003 -002 -002 -001 -009 a -060 -030 -014 -008 -004 -004 -004 -006 A GENTLEMANS WRITING FIRE SCREEN, as in Plate 6, Fig. 3, Two feet fix inches long, the ftandards fix inches wide, a ftraight top, the corners fquare, nine drawers and twelve letter holes infide, the flap to turn down, fupported by quadrants, two ftat-pannekd doors below, one fhelf infide ditto, plain back, claws as No. 1. plate of ditto -280 EXTRAS. Each inch, more or lefs, in length or width — —004 Making ditto with round top — - — - -026 An [ Bo ] • ^ An ovalo, or bead on the comers of tire ftandards, either infide or outfide — — — — — • — — Square clamping the flap — — — — - Miter clamping ditto, each miter extra - - - Veneering the flap, each fide — — — — — Each joint in the veneer, per foot in length - — - Veneering the door frames, long- way - - - 'Ditto crofs-w-ay — — — — — — — Veneering the pannels, each — — — — — Veneering a fiat top — — — — — — Ditto round top — - — _ — - — — — Veneering the ftandards outfide,. each — - — Ditto the edges, each — — — — — Each comer ftring on the ftandards or rails, per foot — Lipping the flap for cloth, fet againft cleaning up. Lining the flap with cloth — - — — — A drawer in front between the flap and doors, partition included, cock beaded — — — — — If two drawers in the length — — — - — Veneering each long drawer front — - — — Ditto each fhort ditto — — — — — — Each butt joint in the veneer — — — — — Each extra fhelf infide the lower part - — — Fram’d back, when the edges of the framing is left fquare, each pannel — — — — — — — Ditto, when the edges are ftuck with an ovalo — — Ditto, when bead and flufli _____ For the price of extra work infide — See Secretary Drawer. Crofs-banding, &c. — See Tables of ditto. Oiling and polifhing ______ £' s - d ‘ 006 006 00 6 008 002 016 024 006 004 006 006 002 o o 1 006 020 0 3 3 004 002 i 003 004 006 009 o 011 009 A LADY’s [ 8i ] A LADY's CABINET, as in Plate 7, Fig. 1. Two feet fix inches long, one foot fix inches from front to £ . s. d. back, framing four inches deep, one drawer in ditto, cock beaded, a flap nine inches wide hing’d to the front with card-table hinges, fupported by two lopers to draw out at the top of the legs, a cafe on the back part nine inches wide and nine inches high, a cupboard at each end, plain doors to ditto, the center part open, flat top, miter dove-tail’d on, plain taper legs, and an aftragal round the bottom of the frame — — — —170 EXTRAS. Each inch, more or lefs, in length and width — — 0 0 4 Ditto in depth of framing — — — — — 0 0 2 Square clamping the flap or doors, each — — — 0 0 3 Miter clamping ditto, each miter extra — — — 0 0 6 Veneering the flap — — — — — — — 0 0 6 Ditto the drawer front — - — — — — 0 0 4 Each butt joint in the veneer — — — — — 0 0 3 Veneering the end rails, each — — — — — 0 0 3 Ditto the back rail — — — — w. — 0 0 3 t Ditto the doors, each — — — — — 0 0 2 Veneering the edges and uprights — — — — 0 0 4 Ditto afkew or crofs-way, at per foot — - — — 0 0 1 Ditto with king, tulip, or any other hard wood, at per foot 0 0 1 2 Veneering the ends of cupboard, each - — — 0 0 2 Ditto the back, either fide - — — — — 0 0 6 M If [ 82 ] £■ If two drawers in the length in place of a long one, extra o Veneering each fhort drawer front — — — — o Each extra miter in the affragal, when the legs project — o When the end and back rife above the top to form a book hi elf — — — — — — — — o When a ffraight top, four inches wide, and the ends fquare o Making the top round, extra — — — — — o Ditto ferpentine, as in plate — — — — — o Veneering each top, when flat - — — — — o Each break in the top of the cafe — — — — o An affragal or ftone moulding round ditto — — — o Each extra miter in ditto, when breaks — — - o Each corner firing, per foot — — — — — o For the price of work in cupboards — See Secretary Drawer. Sweeping the ends hollow, as in plate — — — o A flap, fquare clamp’d, to draw out from under the top, and hing’d to let down to inclofe the front, extra from doors - — — — — - — — o Veneering ditto — — — — — — — o Lipping the top and flap for cloth, fet againft cleaning up. Lining ditto with cloth — — — — — — o Oiling and polifhing ------ o s. d. 1 6 ° 3 0 Ojf 1 o 1 o 1 o 2 O o 4 O 1 o 6 o o\ O 1 O 3 2 O o 6 o 6 o 8 A LADY's C 8 3 ] A LADY’s WORK TABLE, as in Plate 7, Fig. 2. £. s. d. One foot eight inches long, one foot four inches wide, framing four inches deep, one drawer in ditto, cock beaded, plain taper legs, the top part nine inches high, and eight inches deep, made to take off, one long and two fhort drawers in ditto, tray top, the ends fweep’d, the drawers cock beaded, a bead on ends, and back to receive the top part — — - — - - 0150 EXTRAS IN THE LOWER PART. Each inch, more or lefs, in length - - - Ditto in width — — — — — — Ditto in depth of framing — — — — Aftragal at the bottom of the framing ’ — — Ditto, when continued on the back — — — Each extra drawer in depth, cock beaded — — If two fhort drawers in place of one long one, extra Veneering each long drawer front — — — Ditto each fhort — — — — — — — If crofs- way, eaeh joint extra — - — — Veneering the end rails, when one drawer in depth, each Ditto the back rail — — — — Veneering the end rails, when two drawers in depth, each Ditto the back rail — — — Veneering the top — — — — — — . Each joint in the veneer — — — — — . m 2 0 0 2 002 002 006 008 0 1 9 010 003 002 001 002 002 003 0 0 3 i 006 003 An [ 84 ] £• s • d - An aflragal or ftone moulding all round the top, or the edge veneer’d, with a firing in the upper comer — o A firing in the lower corner of the top, per foot — — o Springing the legs one way, each leg — — — — o Ditto both ways, as in plate — — — — — o Veneering the legs, when fprung one way, each — - o Ditto, when fprung both ways — — — — o Each corner firing in the legs, when fprung — — o For the price of flretcher — See Oval Work Table, or RiJing- top Writing Table. EXTRAS IN THE UPPER PART. Each inch, more or lefs, in length — — — — o Sweeping the back edge of the top ferpentine — — o Veneering the long drawer front — — — — o Ditto each fhort — — — — — — — o Ditto crofs-way, each joint extra — — - - o Veneering partition edges afkew or crofs-way, at per foot extra - -- — — - -- o Ditto with king, tulip, or any other hard wood, at per foot extra — — — — — — — — o Veneering the top - — — - — — - o Veneering the outfide of the ends, each — — — o Ditto infide, above drawer - — - - — o Ditto the back - - — - — — — o If crofs-way, each joint extra — — — — — o Letting a band in on the edge of the ends and back, to form a triple firing when the ends are fweep’d, as in plate, and the back flraight — - — — — o Ditto, when a ferpentine back — — — - - o A handle to the top part glued up in four thickneffes — o o 8 o 1 o 2 o 6 o 8 o 10 o 1 } O 2 O 2 O 2 O I O 1 O 1 O 3 O 2 O 1 ° 3 O 1 1 o 1 2 1 4 Each k0|« W|| [ 8 5 ] f * . s . d» Each extra thicknefs in ditto - ~ — - — 001 Veneering ditto crofs-way, each edge — — — —004 Rounding the edges of the handle when veneer’d crofs-way, each edge — - — — — — 002 An extra top for writing, to fold from the middle, lip’d for cloth - — — — — — — 026 Clamping the under top to appear as folid — — —006 Lopers to fupport the flap - — — — — 016 If the front of the foot is fixed to the end of the loper, extra — — - - — — — - 003 Lining the flap with cloth — - - — — 004 A framed Aider to draw out at one end, rabbited for an oval work bag, with a board for the bottom of the bag 030 Oiling and polifhing — — — — — — 006 A PEMBROKE TABLE, Two feet fix inches long on the bed, by three feet four when open, one fly on each fide, the framing four inches and a half deep, one drawer, fcratch beaded, fquare edge to the top, and plain Marlbro’ legs - - —096 EXTRAS. Each inch, more or lefs, in length — Ditto in width — — — — Ditto in depth of framing — — Canting corners of the flaps — — -002 -002 -003 - o o 4 Rounding [ 86 ) Rounding the corners of ditto - — — — Ditto* with quarter round corners — — — Ditto with ovalo comers — — — — — Sweeping the top oval or eliptic _ _ _ Ditto Terpentine — — — — — — Rounding the edge of a fquare top - - Ditto an oval, eliptic, canted, or round comer top - Ditto a quarter round comer top - - — Ditto an ovalo corner top — Ditto a Terpentine top - - - - — Rounding the edge with one fquare, when a fquare top Ditto an oval', eliptic, canted, or round corner top — Ditto a quarter round corner top - — — Ditto an ovalo corner top - — - - Ditto a Terpentine top _ — _ _ _ An aflragal, or hollow and two beads on the edge of fquare top — — — — — — Ditto an oval, eliptic, canted, or round corner top Ditto a quarter round comer top — — _ Ditto an ovalo corner top — — — — Ditto a Terpentine top - - _ _ — Bevelling the edge of an oval top, when folid — Veneering the edge of a fquare or canted top, per foot Ditto with king, tulip, or any other hard wood — Veneering the edge of an oval, eliptic, or the fweep part a round corner top, per foot — — — — Ditto with king, tulip, or any other hard wood - ftraight part — If ovalo or quarter round corners < fweep ditto — each break - Veneering the edge of a ferpenfine top, per foot — of £■ s. d. O o 6 O o io o 1 o o o 9 o 1 3 o o 6 o o 8 o o IO o 1 o o 1 o o 1 o o 1 2 o 1 6 o 1 IO o 2 o o 1 3 o 1 6 o 1 10 o 2 3 o 2 6 o o 3 o o i o o i* o o *2 o o 2 o 0 1 o o it o 0 i o o r-L X 2 Ditto r 87 ] Ditto with king, tulip, or any other hard wood — Veneering the edge of an oval top when bevel’d, per foot Crofling the joint, each ------ A comer firing, per foot - - - - - Each internal miter in comer firing - — • — - Staining the edge of the top _____ — Ditto the joints - — — — - — — — Sweeping the end rails — — — — — — Veneering the end rails of a fquare frame — — — Veneering fweep end rails — — — — — Ditto crofs-way, each joint extra - — - — Glueing up the top, at per joint — — — — Clamping the bed crofs-way - - - - - Ditto the flap, each clamp — — — — — Veneering the top — — — — — — — Each joint in the veneer, per foot in length — - — Veneering the flaps inlide, each - - - — Each extra fly - — — — — - — Each extra drawer in a fquare frame, fcratch beaded - Cock beading ditto ------ A comer firing in ditto -- — — — — Each extra drawer in a fweep’d frame, fcratch beaded — Cock beading ditto ______ A corner firing in ditto _ For the price of work inflde the drawer — See Furniture Drawer. If canniflers — See Tea Chejl. Aflragal round the bottom of a fquare frame - - Ditto when fweep’d end rails - - - — — Each extra miter in ditto, when the legs projedl - - £■ s - d - 0 0 2 0 O l\ 001 OOl 0 o oi 006 006 0 2 0 0 0 6 0 0 8 001 OOl 0 0 6 0 0 2 0 2 0 0 0 2 OO4 0 0 6 O I 6 0 0 3 OO3 0 2 0 OO3 0 0 3 0 0 6 0 0 8 O O 04- Making [ 88 ] Making the bed to Aide, and preparing the infide for a draft or backgammon board - — - — - If no drawer in ditto, dedudt the price of ditto. Letting in the fquares for drafts - - - - Ditto points for backgammon - - — - - Making a folding frame for ditto - — - - Sawing out each leg — — — — — — Tapering ditto, each fide — — — — — For the price of extra work in legs — See Tables of ditto. If made with framing below to receive wire work and cur- tains, with a door at one end, the upper edge of rails rab- bited and moulded, legs only rabbited, a bottom and top to cupboard — — — — — — — If legs are moulded to miter with the rails, extra - - Making a hollow door with a moulding on the frame, the rail lhaped and rabbited to receive the door, when the drawer front is ftraight, extra — — — — Ditto in two doors - — — — — — — If the oppofite end is made to fham a hollow door, when drawer front is firaight ------ Ditto to fham two doors — — — — — If the drawer front and end rails are hollow’d, each end Putting in the wire, each pannel _____ Ditto curtains, each ______ Veneering each door frame, long-way — — _ Ditto crofs-way — — — — — — — A turn’d ftretcher fix’d in center-bit holes by a pin at each If fixed to the legs and fixed with ftretcher plates - - Champhering a ftretcher to appear o&agon or fquare revers’d — — — — — — — — f . s . d . 050 036 026 020 000 000 0 10 O 0 2 O O 3 0 O 4 6 O 4 0 O 5 0 O 1 3 O 0 6 O 0 3 O 0 8 O 1 0 O 1 0 O 1 0 O 1 0 A flat wl> '[ 89 ] £. s. d. o i 6 A flat ftretcher, fweep’d fides and ends - - For the price of crofs-banding, &c. — See Tables of ditto. Oiling and polifhing — - — — — — — 006 C »©«0«©*©tO<’©< , ©< , ©< 3 AN UNIVERSAL OR SLIDING-FLAP PEMBROKE TABLE, Three feet three inches long on the bed, four feet three inches wide when open, framing four inches deep, the flaps to Aide under the bed, fupported by two lopers each when open, fquare edge to the top, plain taper legs, and an aftragal round the bottom of the frame — - 1 1 o O O — ' — — - . ' ' ■ . x ' i j < ; r t. x t f . r • r EXTRAS. Each inch, more or lefs, in length or width — — Ditto, when the top is fram’d — - — — — Ditto in depth of framing ______ Clamping the bed, fquare clamps _ _ _ _ Ditto the flaps, each ______ Miter clamping ditto, each miter extra _ - _ Glueing up the bed or flaps, either folid or to veneer on, each joint — — — — — — — — Veneering the bed - - — — — • — - Ditto the flaps, each ______ Each joint in the veneer, per foot in length - - - Framing the bed with two pannels flufh on the top fide, the framing miter’d at the corners _ _ _ _ 0 0 3 0 0 4 0 0 2 0 0 8 0 0 4 0 0 6 0 0 1 0 I 6 0 0 9 0 0 2 0 4 6 Ditto [ 90 ] Ditto the flaps with one pannel, each — — — - Each extra pannel in the bed or flaps — — — - Veneering the pannels on either flde — — — — Each plate let in acrofs the bed — — — — - Each bolt to keep the flaps level with the bed — — Veneering the edge of the top, at per foot — — — Corner firings on the edge of the top, per foot — — A hollow under the edge of the flaps — — — — A plain drawer — — ' — — - — — Ditto on each fide, or one with a double front to run either If two fhort drawers in the length — — — — Veneering each long drawer front — - — — Ditto each fhort — — — — — Veneering the end rails long-way, each — - - If crofs-way, each joint extra — — — — — A plain Aider in the drawer, fquare clamp’d and lip’d for cloth ________ Ditto, when a double front drawer _ — _ — Lining the Aider with cloth _ — — - _ For the price of extra work in Aider — See Dr effing Chejl. For the price of work in fide the drawer — See Furniture Drawer. Sawing out each leg ______ Each extra miter in the aAragal, when the legs project — For the price of crofs-banding, extra work in legs, &c. — See Tables of ditto. Oiling and polifhing — — — — — — £. s. d. o 3 ° 0 i o 030 006 003 001 001 010 030 0 o 046 006 004 003 001 0 2 0 0 2 6 006 000 000 010 A SQUARE [ 9 ' ] A SQUARE CARD TABLE, f ' . j > d. Two feet fix inches long, one fly foot, fquare edge to the top, plain Marlbro’ legs — — — — -076 EXTRAS. Each inch, more or lefs, in length — — — — An extra fly foot — — - — - An aftragal on the bottom of the front and end rails, or fcol- loping ditto — — — — — — — If continued on the back rail, extra — — — — Each extra miter in ditto, when the legs proje( 5 t - - Rounding the edge of the top — — - — - An aftragal, or hollow and two beads on the edge of the top Glueing up the tops, either folid or to veneer on, per joint Square clamping the top, each clamp - — - - Mitering ftuff round ditto for a moulding on both tops - Veneering the tops, each fide ------ Each joint in the veneer, per foot in length — — — Veneering the edge of the tops crofs-way, per foot — Each corner firing in ditto, per foot — — — — Veneering the front and end rails — - — - Ditto the back rail — — — — — — — If crofs-way, each joint extra — — — - — Lipping the top to receive cloth to be fet againft cleaning up. Sinking a folid top for cloth — — — — — Lining ditto with cloth — - - - — n 2 0 0 2 0 0 6 0 0 9 0 0 3 o O ol 006 0 1 3 001 003 010 009 002 ,0 o 1 001 009 003 001 010 o o 9 Sinking t C>2 ] Sinking a groove in the top of each fly rail for cloth - Folding frame, extra — — — — — — Sawing out the legs, each — — — — — Ditto the joint rail ------- Tapering legs, each fide ------ Rounding the corner of tops — —' — — — Rounding the front legs and the corner of the tops - Making a ferpentine front to the above, with ftraight end Sweeping the ends of the top ferpentine — — — Sweeping the end rails half ferpentine _ — — Veneering the front rail ------ Ditto each end rail — — — — — — — If crofs-way, each joint extra — - - — — Veneering the edge of ferpentine top, per foot — — Each corner firing on the front and ends of ditto, per foot A firing between the band and cloth, at per foot — - An aflragal or hollow, and two beads on the edge of the top, when ftraight ends — - — — _ Ditto, when the ends are half ferpentine — — _ For the price of crofs-banding, extra work in legs, &c. — See Tables of ditto. Oiling and polifhing, when lin’d — — — — Ditto, when folid or veneer’d - — - — — £■ s. d. O o 1 0 5 6 o o Ot o o o o o o 6 o 1 6 O 3 6 o 1 o o 3 o o o 9 0 o 6 o o i o o ii X 7. o 0 1 o o oi o 2 o o 2 6 o o 4 o o 6 A CIRCULAR [ 93 ] A CIRCULAR CARD TABLE, Three feet long, one fly foot, fquare edge to the tops, plain Marlbro’ legs — — — — — — £. s. d. o 106 EXTRAS. Each inch, more or lefs, in length - — — — An extra fly foot — — — — — An aftragal round the bottom of the rail, when the legs are flufli — — — — — — — — If continued on the back rail, extra — - — — Each extra miter, when the legs project — — — Rounding the edge of the tops — - - - — An aftragal or hollow and two beads on the edge of tops Glueing up the tops, either folid or to veneer, at per joint Clamping the tops to appear as folid, each clamp - - Veneering the tops, each fide — — — — Each joint in the veneer — — — — — — Veneering the edge of the tops crofs-way - - — Each corner firing, per foot — — — — — Lipping the top for cloth fet againft cleaning up. Sinking a folid top for cloth — - - _ _ Lining ditto with cloth — — — — — — A firing between the band and cloth, at per foot - - Working a hollow on the edge of the under top — — Staining ditto — — _ — Veneering the rail long- way - — _ _ _ Ditto the back rail _ 0 0 2 0 0 6 0 0 9 0 0 3 0 0 0 0 6 0 1 6 0 0 1 0 0 3 0 0 9 0 0 6 0 1 0 0 0 1 0 1 0 0 0 9 0 0 oi 0 0 4 0 0 3 0 0 9 0 0 3 If [ 94 I If crofs-way, each joint extra - — — - - A drawer in front - — - — — — - Sawing out each leg — — — — — — Ditto the joint rail Tapering legs, each fide — — — — — — If made eliptic, extra when the fweep of the ends is quick For the price of crofs-banding, &c. — See Tables of ditto. Oiling and polifhing, when lin’d — — — — Ditto, when folid or veneer’d _ — — — — £• s. d. O O I 040 O O oi 0 O O^ 0 0 0 |- OlO OO4 0 0 6 A CARD TABLE, with CANTED CORNERS, folid fquare edge to the tops, one fly foot, plain Marlbro’ legs A plain drawer in front — — — — — — Veneering the front and end rails — — — — A firing betwixt the band and cloth, at per foot — — Crofs-banding the edge of the top, at per foot — — An aftragal on the bottom of the frame — - — Each extra miter when the legs project — — — For the price of banding — See Table of ditto. All other extras to be paid for as Square Card Table. o 10 6 030 O I o 0 o o\ 001 o o 10^ o o of A CARD TABLE, with ROUND CORNERS, folid, the front legs placed in the center of the corner, fquare edge to the tops, one fly foot, plain Marlbro’ legs - 011 o A plain ftraight drawer in front — — - —030 If fweep drawer front, extra — — - — — 006 An [ 95 ] £. s. d. An aftragal on the bottom of the frame - — — o o 1 1 Veneering the front and end rails - — — —009 All other extras to be paid for as Circular or Square Card Table. C KS> U 0 I> 0 , '0‘'“"0 |, 0*0’0 < 3 A CARD TABLE, with Quarter Round Corners, Three feet long, flraight middle rail, with breaks in front, folid top, fquare edge to ditto, veneer’d rails, one fly- foot, plain Marlbro’ legs — — — - - 0120 EXTRAS. Each inch, more or lefs, in length — — — — An aftragal round the bottom of the rail — — — If continued on the back, extra — — — — Each extra miter when the legs project — — — Glueing up the tops either folid or to veneer on, at per joint 'fweep part, per foot - Veneering the edge of the tops, a flraight part, ditto — each miter — — Corner firings in ditto, fweep ’d or flraight, at per foot — Lipping the inflde with cloth - — — — — Sinking a folid top for cloth. — - — - - Lining ditto with cloth — — A firing between the band and cloth, at per foot — — Working an aftragal or hollow and two beads on the edge of the tops - — — / o o o o o o o o o o o o o 0 1 o o o o o o o 0 1 2 2 3 1 1 I oi 1 3 o 10 O Oj; 03O Working kO|w [ 96 ] Working a hollow on the under edge of the lower top - A drawer in the front — — — — — — Fitting up infide of ditto for backgammon — - - A draft board to hide under the bottom of ditto - — For the price of extra work — See Square or Circular Card Tables. Oiling and polifhing, when the tops are lin’d - — Ditto, when folid or veneer’d — ~ — — — £■ O O O O o o s. o 3 3 5 o o d. 8 o 6 o 7 9 C >© < '<'0 , 0' > 0 < '©«0 <, <2>" 0 A CARD TABLE, with Ovalo Corners, Three feet long, flraight middle and end rails, the corners and front rail veneer’d, one fly foot, fquare edge to the tops, four plain Marlbro’ legs — - — — 0140 EXTRAS. Each inch, more or lefs, in length - - — An aflragal round the bottom of the frame — — If continued on the back rail, extra — — - Each extra miter, when the legs project — — Two extra legs _______ 'flraight part, per foot Veneering the edge of the tops, < fweep part ditto, ditto each break - Each corner firing fvveep’d or flraight, per foot — Lipping the infide for cloth — _ _ — Lining the tops with cloth - _ _ _ 0 0 2 0 1 5 0 0 3 0 0 of 0 2 0 0 0 1 0 0 0 0 1 0 0 1 0 0 6 0 1 0 A firing [ 97 ] A firing between the band and cloth, per foot - - Working an afiragal or hollow and two beads on the edge of the tops - — — - — — — A hollow on the under edge of the lower top — — Veneering the end rails, each — - — — - Ditto the back rail — — — — — — — A drawer in the front — — — — — — Fitting up infide of ditto for backgammon — — — A draft board to fiide under the bottom of ditto — - For the price of any extra work — See Square and Circular Card Tables. Oiling and polifiiing, when the tops are lin’d — — Ditto, when folid or veneer’d - _ - - - Four feet long, the rail two inches and a half wide, ve- neer’d all round, folid top, fquare edge to ditto, four plain taper legs, a pillar and claw ftand in the hollow part, the top of ditto turn’d to receive the bottom of a tin or copper cylinder, two feet over, and made to turn round, a mahogany top fitted into the cylinder, and cut to receive five tin bottle cafes, the claws as in No. 1, plate of ditto _______ £■ s • d - O O 0| O40 OlO 0 0 2 OO3 030 036 05° OOS OO9 C 0«0'>0< 3 A GENTLEMAN’S SOCIAL TABLE, as in Plate 5, 1, o EXTRAS. [ 98 ] EXTRAS. Each inch, more or lei s , in length — — — — Putting on pieces to form brackets on each fide of the legs Rounding the edge of the top — — - — — Aftragal on the bottom of the rail, per foot in length - Each extra miter in ditto, when the legs project — - Framing the top of the Rand with a fquare pannel, flulh on both fides — — — — — — — — Screwing a bead round the edge of the loofe top of the cy- linder — — — — — — — — Each extra hole to receive a bottle cafe — — — When the table is made feparate, and as defcribed in the preamble, dedu6t for the cylinder and fland - - Each extra inch in diameter — — — — — For the price of extra work in legs or claws, &c . — See Ta- bles of ditto. Oiling and polifhing the table - — — - — Ditto the Hand — — — — — — — £ . s. d. O O c o o 8 009 002 000 020 010 004 090 003 006 004 C-0^3'> ,h 3 , “<3> , S>' > 0' , 0 >0|' [ 99 ] Ditto, in depth of framing - - - - - Each drawer the length of the frame, fcratch beaded Each extra ditto in depth — — - — Each drawer when more than one in length, fcratch beaded Cock beading each drawer - - - - - Veneering the front rail — — — — — — Ditto each long drawer front - - — - — Ditto each fhort ditto ------ Ditto each end rail — — — — — — — If crofs-way, each joint extra — - — - - Glueing up the top, at per joint - ’ — — - - Clamping ditto, fquare clamps — — — — — Miter clamping ditto, each miter extra - - — Clamping the top end- way, to appear as folid - — Mitering fluff all round for a moulding — — — Rounding the edge of the top — - — - — Ditto with one fquare, at per foot — — — _ An aftragal or ftone moulding on the edge of the top, or the edge veneer’d, with a firing on the upper corner, per foot Lipping the top for cloth to be fet againfl cleaning up. £■ O O O o o o o o o o o o o o o o o d. 2 9 6 3 3 3 5 3 2 1 1 6 6 6 o 8 O 2 S. 0 1 1 1 o o o o o o o o o o o o o 1 2 * Lining the top with cloth — — — — — o o 6 Ditto with leather — — — — — A rim on the back and ends of top groov’d in, with the o o 9 edge of the rim rounded - - - — — o 1 0 An aftragal on the edge of ditto, extra - — — o o 3 Veneering the top — — - — — — — o o 9 Each joint in the veneer, at per foot — — - — o 0 2 Aftragal on the bottom of the frame, per foot — — o o li If made with circular front, extra — — — o 1 2 A moulding on the front edge of the top, per foot — o o 2 2 Aftragal on the front of frame, per foot - - — o o 2 Each o 2 [ loo ] Each drawer the whole length of the frame — , £■ O s. 2 d. 3 Each extra ditto in depth — — - — — 0 2 o Each drawer when more than one in length — — — o 1 9 Veneering the front rail, when no drawer - — — o 0 4 Ditto each long drawer front — — - — — o o 6 Ditto each Ihort ditto — — — — — — o o 4 An eliptic front with break at the ends, extra from circular o o 8 A ferpentine front, extra from ffraight front — — - o 1 9 A drawer in ditto the length of the frame - — - o 2 9 Each extra ditto in depth - — — — — o 2 6 Each drawer when more than one in length — — — o 2 o Veneering the front rail — — — — — — o O 6 Ditto each long drawer front — — — — — 0 O 8 Ditto each Ihort ditto — — — — — — o o 6 A moulding on the front edge of the top, per foot - o o 3 Aftragal on the front of the frame, per foot — - — o o 2- i Sweeping the front and ends of the top ferpentine fquare frame _____ when a o o 8 Rounding each corner of the top — — - — o o i Sawing out and glueing up drawer fronts— Cheft. If made with a knee hole for extra framing -See Drejfing 0 3 o Sawing out legs, each _ _ _ — - — o o oi Tapering ditto, each fide — — — — — — o o °2 If made with three low rails — — — — — o o 9 For fnelf, &c. — See Rifing-top Writing Table. If only one of thefe, to be extra — — o o 6 Oiling and polifhing _ _ _ - — - o o 4 A STRAIGHT- [ lOI ] A STRAIGHT-FRONT INCLOS’D PIER TABLE. £. s. d. Three feet long, one foot fix inches wide, the back and ends fram’d into the legs, two flat-pannel’d doors in front, pannels plow’d in, one fix’d flielf infide, and an afiragal round the bottom of the framing - - l o o EXTRAS. Each inch, more or lefs, in length or width — — — Glueing up the ends, top, or pannels, either folid or to ve- neer on, at per joint — — — — — — Rounding the edge of the top — _ _ — — An afiragal or fione moulding on the edge of the top, per foot Ditto with a frieze and an afiragal at foot, per foot - Clamping the top to appear as folid — — — — Veneering the top or ends, per foot fquare — - — Each joint in the veneer of top, per foot in length - Each joint in the veneer of ends, per foot in length — Veneering the edge of the top crofs-way, at per foot - Ditto with king, tulip, or any other hard wood, at per foot Each corner firing in ditto, per foot - - — — A rail under the top, two or three inches wide, with an afiragal at foot — — — — — — — Each miter in the afiragal, when the legs project — — Veneering ditto long-way — — — — — Ditto crofs-way, and continued on the ends — - — Cleaning the infide of the rail, putting a bottom in, and hinging the top ------- 004 001 003 002 o o 4F 006 002 002 0 o H 001 0 O lF 001 o i 6 o o of 003 010 030 Each [ 102 ] £■ s - d • Each quadrant to fupport the top — — — — o i o When made to g-o into a recefs, and two or three inches cut off each end and the back, and made faft, and top hing’d in ditto — — — - - “ ~ - 020 Veneering the top edge of the rail - - — -004 Veneering the door frames, long-way - - -020 Ditto crofs-way - - - - - - - 030 Veneering each pannel — — — — — - 009 Cutting down the front legs, and glueing ditto on the ftile of the doors to form pilaflers, each — — — -006 For the price of pilaflers — See Straight-front Library. Each extra long fhelf infide - — - — — 009 An upright partition in the center groov’d for fhelves —020 Each fhort fhelf more than two — - - — o O 6 For the price of extra work in the top, doors, or legs — • See Tables of ditto. Oiling and polifhing — — — — - — 009 A PIER TABLE, with a Break, Three feet fix inches long, fix plain taper or turn’d legs, turn’d to the top of the frame, the top broke round to the fhape of ditto, fquare edge to the top, and an aftragal round the bottom of the frame, the moulding for the legs prepared by the turner - - - — — 0170 EXTRAS. C 103 ] EXTRAS. £■ S. d. Each inch, more or lefs, in length - - - — O O 2 Each inch above four in depth of framing — — — O O 4 A drawer between the middle legs — - — — O 3 0 Each ditto in the wings - - — - - — O 2 0 Veneering the front and ends long-way - — - O 1 3 Ditto crofs-way, each joint extra — - — — O 0 1 Glueing up the top, at per joint - - - — O 0 1 Veneering the top, at per foot fquare - - - — O 0 2 Veneering the edge of the top when turn’d legs - — O 2 0 Ditto when the breaks are fquare and miter’d — — O l 6 Ditto with king, tulip, or any other hard wood, when turn’d legs - - - - - - - 030 Ditto when the breaks are fquare and miter’d - -026 Corner brings in ditto, per foot - - - -001 Rounding the edge of the top, when either folid or veneer’d 013 Working an abragal or bone moulding on the edge of the top - - - - - - - - - 046 Working the fquare parts and glueing on ditto, when the circles are prepar’d by the turner - - — -026 A fhelf, fixed with bretcher plates, fhap’d to the frame, and hollow’d in the middle of the front, with ledge groov’d in - — — — — -- 036 Working an abragal on the edge of ditto, the circles pre- pared by the turner - — — — - - 020 If bretcher rails, fram’d in and rabbited to receive the fhelf 026 For the price of crofs-banding, &c . — See Tables of ditto. Oiling and polifhing - - - - — — 008 An [ 104 1 An INCLOS'D PIER TABLE, with a Break, £■ Three feet fix inches long, one foot nine inches wide, two flat-pannel'd doors in the center, and one ditto in each wing, pannels plow’d in, one fhelf fixed in each cupboard, fix legs turn’d to the top of the framing, the top broke round to the fhape of ditto, fquare edge to the top, an aftragal round the bottom, the mould- An aflragal on the front and ends between the drawers and doors, the turner to prepare the circles for the legs - o s. d. ing for the legs prepared by the turner — — — 2 10 o EXTRAS. Each inch, more or lefs, in length or width — — O o 5 Glueing up the ends, top, or pannels, either folid or to veneer on, at per joint — — — — - — O o I Veneering the door frames long- way, each pair — — o 2 o Ditto crofs-way - - - — — - — o 3 0 Veneering the pannels, each — — - — - o o 9 Each joint in the veneer, per foot in length — — - o o 2 Veneering the ends, each, per foot fquare — - — o o 2 Each joint in the veneer, per foot in length — - — o o 2 For the price of veneering the top, mouldings. &c., on ditto — See the preceding Table. A drawer in the center part above the doors — — — o 3 o Each ditto in the wings — — — — — — o 2 o Each partition — — — — — — — 0 0 6 Lining ditto crofs-way, each — — - - — o 0 1 2 O Each [ i°5 1 £. s. d. Each faft fhelf more than three — — — — — 006 Fram’d back, each pannel - - - - -006 Oiling and polifhing — -- - — - — 016 A ROUND-FRONT PIER TABLE, With Straight Ends, Three feet long, one foot fix inches wide, the framing four inches deep, fquare edge to the top, plain Marlbro’ legs 060 EXTRAS. Each inch, more or lefs, in length or width — - - Ditto in depth of framing — — — — — An aftragal or ftone moulding on the edge of ) flraight part the top, per foot - — — )fweep part Glueing up the top, either folid or to veneer on, at per joint Veneering the top — — — — — — — Each joint in the veneer, per foot — — — — Veneering the edge of the top crofs-way, per foot — — Ditto with king, tulip, or any other hard wood, at per foot Each corner firing in ditto, at per foot — — — Veneering the front rail long-way — - — — Dkto the end rails, each — — — — — — If crofs-way, each joint extra ------ Cleaning the infide of the rails, putting a bottom in, and hinging the top — — — — — — — p 002 003 0 0 2 0 O 2| 001 OO9 0 0 2 0 0 1 0 O 14- 001 004 0 0 2 OOl ° 3 6 For flraight part fweep part [ 106 ] For other work in top, & c. — See Straight -front Inclos'd Pier Table. A fmall flone moulding on the edge of the top, with a veneer’d frieze and aflragal at foot, per foot — — — — A plain tablet on the rail — — — — — — A lipping round ditto - — — - — — A fmall moulding round ditto — — — — — Breaking the tablet below the rail — — — — Each extra miter in the moulding, when broke — — Veneering ditto long-way — — — — — If crofs-way; each joint extra - — — - - A butt joint in ditto -- — — — — A break in the top to project over the tablet — — Moulding the edge of the top, or veneering "1 ditto crofs-way, with a firing in the upper L ralfc> ^ art corner, per foot — — — j ^ wee P P art A llring in the lower corner of ditto, at per foot — — If the front rail and top is made ferpentine, extra — An aflragal or flone moulding on the edge of a ferpentine top, per foot — — — — — — — A fmall flone moulding, with a veneer’d frieze, and aflragal at foot, on ferpentine part, per foot — — — Sawing out each leg ------ Tapering ditto, each fide _____ For the price of extra work in legs, crofs-banding, &c. — See Tables of ditto. Oiling. and polifhing ______ 0 £. s. d. o o o o o o o o o o o o o o o o o o o o o o 4 1 5 5 4 6 2 2 1 2 6 002 0 O 2\ 001 OlO OO 7 \ o o o o o4 Or A ROUND- (0|>1 to I' [ i°7 1 A ROUND-FRONT INCLOS’D PIER TABLE, With Straight Ends, £. s. d. Three feet long, one foot fix inches wide, two flat-pan- nerd doors in front, the framing plow’d and pannels bent in, one fix’d fhelf infide ditto, the back and end rails fram’d into the legs, and an aftragal round the bot- tom of the framing - - - - - — i 10 o EXTRAS. Each inch, more or lefs, in length or width — — — Glueing up the pannels to the fweep, at per joint — - Veneering ditto, each - — Each joint in the veneer, per foot in length - - - Veneering the door frames long-way - - - — Ditto crofs-way -------- A rail, two or three inches wide, under the top moulding, with an aflragal at foot — — — — - Veneering ditto long-way, per inch in width - — Ditto crofs-way, each joint — — — — — If the front is made ferpentine, the doors glued up, clamp’d and veneer’d outfide - — — Veneering ditto infide — — — — — — Each joint in the veneer, per foot in length — — — A rail under the top moulding, two or three inches wide, and an aftragal at foot of ditto — — — — Veneering ditto long- way, per inch in width — - Ditto crofs-way, each joint - - — — — o ° 5 o o if O 1 o o o 2i O30 040 0 2 0 0 0 2 O O Oj O30 O36 OO3 029 0 0 3 O O Of For p 2 [ io8 ] £. s. d. For the price of drawers or Aider above the doors — See Round or Serpentine-front Dr effing Chef. Glueing up the top, veneering ditto, See. — See the preceding Table. Oiling and polifhing — — — - — — oio C k£>'O<>*0><«S>»O < ‘O <, O < ^S> A CIRCULAR PIER TABLE, Three feet long, fquare edge to the top, and plain Marlbro’ legs - -- -- -- - EXTRAS. Each inch, more or lefs, in length — - — — If made eliptic, extra ______ An Aftragal round the frame _ - - - _ Each miter, when the legs project _ _ _ _ Working an aftragal, or hollow and two beads on the edge of the top, per foot ______ Veneering the front rail long-way _ _ _ — If crofs-way, each joint extra — - - - — Glueing up the top, each joint — — — — - Lining up the top, at per foot in length — - - Clamping up the top to appear as folid, each clamp - Veneering the top, per foot in length - _ — Veneering the edge of ditto crofs-way, at per foot — Each corner firing in ditto, at per foot — — — A hollow or torus under the top, fixed on the frame, per foot A torus, with a hollow at foot, at per foot — — — o 7 6 o o 2 o o 6 o o 9 o o °4 o o 2 o o 9 o o 1 o o 1 o o 4 0 o 3 o o 3 o o o o i o o 3i o o 5 Each [ log 1 Each miter in ditto when the legs project — - — o o Staining the hollow — — — — — — o o For the price of a tablet — See Round-front Pier Table. A drawer between the two front legs — — —04 A fhelf fweep’d as the rail, and fix’d with ftretcher plates flufh with the feet — — — — — — 01 A ditto, hollow’d between the legs - — — —01 Grooving a rim in either of the above ftretchers — —01 Working an aflragal on the edge of a round-front fhelf -00 Ditto on the edge of a hollow’d fhelf — — -01 Breaking ditto round the legs, each miter — — -00 Veneering the fhelf, per foot in length — — —00 A ftretcher, the three fronts fweep’d hollow, and tenon’d into the legs — — - — — — — 04 Veneering ditto, each fide, per foot — — — -00 Corner firings in ditto, at per foot — — — — o O Making a circular frame without a top — — — o 5 Ditto an eliptic frame — — — — — — 06 Each extra inch in length of a frame — — — —00 Ditto on the top — — — - — — — 00 Sawing out the legs, each - - — - -00 Tapering ditto, each fide — — — — _ 0 o For the price of crofs-banding, extra work in legs, &c. — See Tables of ditto. Oiling and polifhing - — - - — - 00 d. 1 3 o 6 9 o 6 3 of 3 o 1 o 4 A C 1 R- ' .i . C ° 110 ] A CIRCULAR INCLOS’D PIER TABLE, Three feet fix inches long, two doors in the middle part, glued up and clamp'd, one (ham ditto at each end, a fall fhelf infide, the front veneer’d all fhtfh, edge of the top fquare, an aftragal on the edge of the bottom, on taper flump feet - - - - — - -117 EXTRAS. Each inch, more or lefs, in length — — — —00 Eliptic fweep, extra when the ends are quick — -02 A rail, two or three inches wide, under the top moulding, with an aftragal at foot of ditto - — — —02 For the price of glueing up the top, veneering and mould- ing ditto — See the preceding Table. Each inner end, when drawers within the doors in the middle — - - - — — - — 01 Dedudt for the fhelf — — — — — — 01 Each drawer not exceeding nine inches deep, fcratch beaded o 3 Cock beading ditto — — — — — — 00 Each inch deeper — — — — — - — 00 Each partition - - - - - — - 00 Veneering each drawer front — — — — —00 A cupboard in either end, with a fhelf, in place of fham doors — - - - - - ■— - 03 Each extra fhelf in ditto — — - — — — 00 Each fhelf in the middle part — — — — —00 If drawers in the middle, in place of doors, dedudl for doors and fhelf — - — — — — — 012 Then add for drawers and partitions as above. O 6 6 6 6 o 6 4 7 9 o 5 9 o Sawing [ 111 ] £. s. d. Sawing out drawer fronts, and glueing up ditto — See Round- front Drejfmg Chef. If made for japanning, deduct for veneering or poundage. For the price of pilafters — See lower Part of Straight- front Library. Fram’d back, each pannel - — - - - o O 6 For the price of crofs-banding, extra work in legs, &c. — See Tables of ditto. Oiling and polilhing - — - - — — 013 Cx£>x£> > <£>"’' "0»<2>'' '3 A PIER TABLE, with Ovalo Corners, Three feet long, one foot fix inches wide, ftraight mid- dle, and fweep end rails, the frame veneer’d, the edge of the top fquare, four plain Marlbro’ legs — — —090 EXTRAS. If a break in the corners and ftraight end rails, with aftra- gal broke to ditto ______ 0 Two extra legs to form the break, extra — — — o Each inch, more or lefs, in length or width — - - o Each inch above four in depth of framing - — — o An aftragal on the bottom of the frame - — — o Each extra miter in an aftragal, when the legs project - o Glueing up the top, at per joint - - _ - o Lining up the top, at per foot in length - - - o Veneering the top, at per foot in length - - - O 2 o l o o 2 0 4 1 6 o o| o 1 0 3 0 3 Each C 112 3 Each joint in the veneer, per foot foot £■ J. d. _ _ O o 2 ftraight part O o 1 fweep ditto O o 1 each break o o I _ _ o o 1 top, at per Each corner firing, per foot Working an aftragal, or hollow and two beads on the edge of the top _______ A plain fhelf, fweep as the rail, and fixed with plates - If low rails to ditto, framed into the legs _ _ _ A drawer between the front legs — — — — If two in the length ______ Sawing out each leg ______ Tapering ditto, each fide — — — _ — _ For the price of extra work in legs — See Tables of ditto. Oiling and polifhing o o o o o o o 2 2 3 2 4 o o o o o 9 6 °i o4 - o C O'©*©"© j An INCLOS’D PIER TABLE, with Ovalo Ends and Straight Middle, Three feet fix inches long, one foot fix inches wide, two plain flat-pannel’d doors in the middle, one fixM fhelf infide, the edge of the top fquare, an affragal round the edge of the bottom, on four taper flump feet - - — - — - — - - l 10 O EXTRAS. [ “3 ] EXTRAS. Each inch, more or lefs, in length or width - - - For the price of glueing up the top, &c. — See the pre- ceding Table. Veneering the ends, each — — — — — A drawer in the front - — - — — - Veneering ditto _______ If the upper part of the ends are veneer’d long-way, when to fham a drawer front, each extra — - - — Two extra legs, with end rails to ditto - — — A cupboard in either end, with door clamp’d, lock’d, and hing’d — — — — — — — — Each fhelf in ditto — — — — — For the price of crofs-banding, extra work in doors, &c. — See Tables oj ditto. Oiling and polilhing — £. s. d. 006 o 1 6 029 004 00 6 060 026 005 o 1 9 A PIER TABLE, with Circular Middle and Hollow Ends, as in Plate 7, Fig . 3, Left-hand End , Three feet fix inches long, one foot eight inches wide, two doors in the middle part, glued up and clamp’d, one fham ditto at each end, a faft fhelf infide, the front ve- neer’d all flufh, edge of the top fquare, an aftragal on the edge ot the bottom, on taper flump feet Q 230 EXTRAS. [ J EXTRAS. £ Each inch, more or lefs, in length or width - — - o An aftragal or hollow and two beads on the edge of the top o A fmall ftone moulding on the edge of the top, with a frieze and aftragal at foot - — — _ — o A rail under the top, two or three inches wide, with an aftragal at bottom of ditto — — — — - o Glueing up the top, at per joint — - — — o Lining up the top, at per foot in length — — — o Veneering the top, at per foot fquare — — — — o Each joint in the veneer, per foot in length — — — o Veneering the edge of the top, at per foot - - — o Each corner firing, per foot — — — — — o Each cupboard in the ends, with a faft ftielf in place of fham door - - — - — - o Each extra ftielf in ditto — — — — —— o If inner ends, drawers, &c. in the middle — See Circular Inclos'd Pier Table. For the price of crofs-banding, &c. — See Tables of ditto. Oiling and poliftiing - - - _ _ s . d . o 6 2 O 4 6 3 3 o i ° 3 O 2 O 2 O O 1 3 6 ° 5 i 6 A PIER [ 1 A PIER TABLE, with Circular Middle and Ogee Ends, as in Plate 7, Fig. 3, Right-hand End , £' d. Three feet fix inches long, one foot eight inches wide in the center, two doors in the middle glued up and clamp’d, a faff fhelf infide, the front and ends veneer’d, the edge of the top fquare, an aftragal on the edge of the bottom, on taper Hump feet - — — -270 EXTRAS. Each inch, more or lefs, in length or width - - - 0 0 6 Each cupboard in the ends, with a fix’d fhelf in place of fham door - - - - — — — 0 4 0 Each extra fhelf in ditto — — — — — — 0 0 5 An aftragal or hollow and two beads on the edge of the top 0 2 6 A fmall ftone moulding, with a frieze and aftragal at foot 0 5 0 A rail under the top, two or three inches wide, with an aftragal at foot of ditto — - — — - 0 4 0 Glueing up the top, at per joint - — - — 0 0 1 Lining up the top, at per foot in length — - — 0 0 3 Veneering the top, per foot fquare - - - — 0 0 2 Each joint in the veneer, per foot in length — — - 0 0 2 Veneering the edge of the top, at per foot — — — 0 0 if Corner firings, per foot - - - — — — 0 0 1 If drawers, &c., in the middle — See Circular Inclos'd Pier Table. Q 2 For [ u6 ] £■ s- d. o i 6 For the price of crofs-banding, See. — See Tables of ditto. Oiling and polifhing — — — — — — C ■©»©<■©< 0-''0'<2x0'0" , D A STRAIGHT-FRONT SIDEBOARD TABLE, Four feet fix inches long, two feet fix inches wide, fra- ming five inches deep, the edge of the top fquare, four plain Marlbro’ legs, and an aftragal round the bottom of the frame - — - - - - — 0100 EXTRAS. Each inch, more orlefs, in length or width - - - Ditto in depth of framing - - - - - Glueing up the top, at per joint - - - - Glueing up a folid top, each joint, at per foot in length — Lining up the top, at per foot in length — — — Lining the ends of top on the miter to appear as folid, extra ________ Veneering the top, at per foot fuperficial _ _ — Ditto the edge, at per foot — — _ _ _ Each corner firing on the top, at per foot — _ _ Canting the front corners of the top — _ _ _ Ditto the legs, each — — — Rounding the front corners of the top _ _ _ A plain tablet on the rail — - _ _ _ A lipping round ditto to form a pannel — _ _ A fmall moulding ditto ______ 002 003 002 0 o of 003 010 0 0 2 001 OOl 0 0 2 O O if 004 0 0 6 OO 5 OO7 Breaking C 117 ] Breaking the tablet below the rail - - - - Each extra mi:er in moulding or lipping, when broke - Veneering ditto — — — — — — — A butt joint in the veneer - - - - - A tablet drawer - — — Each break in the top ______ A drawer the whole length of the frame — _ _ If tw r o in the length ______ If three ditto — — — — — — — If four ditto — — — — — — — — Veneering the rails long-way, per foot — — — Ditto when drawers, each drawer extra - — — Ditto crofs-way, each joint extra — — — — Two extra legs — — — — — — — When the middle legs project their whole thicknefs, for legs and extra framing _ _ _ _ _ If made with an eliptic middle, fweeping the rail and top Ditto, when a drawer is introduced, including drawer - Veneering the eliptic part, per foot in length — - Ditto, when a drawer and partition edges - — — A fmall ftone moulding on the edge of the top, with a frieze and aftragal at bottom of ditto, at per foot — Ditto, when an eliptic middle, the fweep part, at per foot Each miter more than two — — — _ _ Rabbiting in a moulding when a veneer’d top, the fame price as when folid. A hollow or torus round the top of the frame, when the legs are flufh, per foot — — — — — — Each extra miter, when the legs project - — — Ditto when an eliptic middle, fweep part _ _ _ £. s. d. 0 0 2 0 0 0 | OO3 003 030 004 036 O 46 066 086 OOl^ OOl 001 0 2 0 O36 O4O 080 003 004 O o 4i 007 002 002 001 003 A torus [ u8 ] £. s, d. A torus moulding, with a hollow at foot round the top of the frame, per foot - - — — — — o Ditto, when an eliptic middle, fweep part — — — o Each extra miter in the aftragal at the bottom of the frame o Rounding the edge of a folid or veneer’d top — — o Ditto when breaks, each break extra — - — — o Letting in each plate for rods — — — — — o A flap at the back hung with a rule joint, and fupported with two brackets - — - — - - o Every three inches exceeding four teet lix inches in length o Sawing out the legs, each — - — — — o Tapering ditto, each lide - - — - — o For the price of extra work in legs — See Tables of ditto. Oiling and polifhing, at per foot in length - — — o ° 3 ° 5 o of o 6 O 1 O 1 4 6 O 2 O 1 O Oy O 2 C ■<©>>0 , ' > >0 J A STRAIGHT-FRONT CELLERET SIDEBOARD, Five feet long, two feet fix inches wide, the framing fix- teen inches deep, a deep drawer at one end prepared for the plumber, a plain drawer or cupboard at the other end, with one fhelf infide, a fhallow drawer in the mid- dle, edge of the top lquare, lix plain Marlbro 5 legs, and an aftragal round the bottom of the frame, folid -170 EXTRAS. Each inch, more orlefs, in length or width Ditto in the depth of framing - - o 6 0 5 For o [ 1 For the price of glueing up the top, veneering ditto, &c. — See the preceding Table. Partitioning with mahogany mitered, or any other work — See Square Celleret. When the middle legs projedt their whole thicknefs, extra It two drawers in place of a deep one, with extra rail in front If ditto with partition from front to back - — An extra drawer above the celleret, partition included - A pot cupboard in the end, cock beaded — — — Hinging the front to let down, and fixing a quadrant to fupport ditto _______ An eliptic middle drawer, extra from ftraight — — An extra drawer in depth, in the middle ol a ftraight front, partition included ______ Ditto, when eliptic ______ Two extra legs — — — — — — — Veneering the front ______ Ditto when made with an arch _ _ _ _ Veneering each extra long drawer _ _ _ _ Ditto each extra fhort ditto - — — - — Ditto the end rails, each _ _ _ _ _ Ditto each middle rail or back in the knee hole — — A loofe ciftern for bottles _ _ — - _ A fmall ditto to wafh glalTes in _ _ — — A plain ftraight-front arch cock beaded — — - A plain eliptie arch cock beaded - — — — A triple firing round the bottom of the arch the fame as cock bead. f . s. d. 036 o 1 9 0 2 0 0 2 6 0 2 6 O 1 3 O5O 0 3 3 04 6 02 6 02 6 030 006 004 005 003 020 o i 6 016 030 Each pannel in the arch, formed by a fingle firing Ditto by a double firing - - _ _ Ditto a triple firing _ _ _ _ 004 005 006 Letting [ 120 ] £• Letting in a fan or pannel, each - - - - o Ditto, when eliptic — — — — — — o Making a pannel of veneer, and letting ditto into a flraight front with a lingle firing round - - - — O Ditto an eliptic front — - — - - — o Each extra firing round ditto — — — - — o A plate drawer with the arch to draw out, extra from a fixed arch — - — — - — — o Ditto when an eliptic middle — — — — — o When the front of the drawer is made to Hand three or four inches behind the arch, the fpace filled up even on the top fide and veneer’d - — — - — o Ditto when an eliptic front — — — - — o If the drawer front is eliptic, extra - - — — o When the front is hing’d to fall down within a fixed arch, extra from a common arch — — — — - o When the front is made to fall down with quadrants, carry- ing the arch w r ith it, extra from a fix’d arch - — o When an eliptic ditto, for filling up infide — — — o Veneering plate drawer front, flraight — — — o Ditto, when eliptic — — — — — — o A tambour cupboard behind the arch, and aftragal continued on the bottom of the rails — — — — — o A Aider on the top of the plate drawer to Hide back - o Oiling and polilhing, at per foot in length - — - o s. d. ° 3 ° 5 o 6 o 8 o I 4 ^ 5 6 6 6 7 6 1 o 3 o 3 6 2 6 o 8 0 10 6 o 1 6 O 2~2 A ROUND- [ 121 ] A ROUND-FRONT SIDEBOARD TABLE, With Straight Ends, £. s. d. Four feet fix inches long, two feet fix inches wide, fra- ming five inches deep, the front rail veneer’d, the edge of the top fquare, four plain Marlbro’ legs, and an aftragal round the bottom of the frame - — - —0140 EXTRAS. Each inch, more orlefs, in length or width - — - Ditto in depth of framing — — — — — When made eliptic, with the legs to fiand either bevel or fquare, extra from the ftart — — — — — Making the end rails half eliptic, with the aftragal broke round ditto - — — - — - — — Glueing up the top, at per joint — — — — Glueing aip a folid top, each joint, at per foot in length - Lining up the top, at per foot in length — — - Lining the ends of the top on the miter to appear as folid, extra — — — — — — — — Veneering the top, at per foot fuperficial - - - Veneering the edge of ditto, at per foot ] * uee P P Jrt t ftraight part — Corner firings on the top, at per foot - — - — Rounding the edge of the top — — — — _ Ditto when breaks, each break extra - - — - R O O 2v 0 0 3 016 030 0 0 2 OOO^: O03 OlO 0 0 2 0 O ljr 0 0 1 001 00 6 o o 1 A fmall o o [ 122 J A fmall ftone moulding: on the edge of . , • , r ■ in , lweep part the top, with a frieze and aftragal at > n . . 11 r .• r ' ftrajght part - the bottom of ditto, at per foot — Each extra miter, when the legs project — — — o A hollow or torus round the top of the frame, when the legs are flufh, fweep part, per foot — - - o Ditto ffraight part — — — — — — — o A torus moulding, with a hollow at foot, fweep part, per foot — — — — — — — — — O Ditto ffraight part — — — — — — — O Each extra miter, when the legs project — — — o Ditto in the aflragal at the bottom of the frame — — o A tablet on the rail — — — — — — — o Veneering ditto - — — — - — — o Each butt joint in the veneer — — — — — o A tablet drawer, including partitions — — — — o When made with three drawers, each end drawer, in- cluding linings - — — - — — — o Two extra legs, not bevel’d — - — — — o Ditto, when bevel’d — — - — — o Veneering the end rails, each — — — — — o Ditto crofs-way, each joint extra — - — — o A cupboard in the end rail, with a plain door — — o Hollowing out the end rails, each - — - — o An aftragal on ditto, extra — — — — - o Sawing out the legs, each — — — — — o Tapering ditto, each fide — — — — — o For the price of extra work in legs, &c. — See Tables of ditto. Oiling and polifhing, at per foot in length — - - o £. s . d. o 6 o 4i o O 2 O o o o o o o 3 3 2 2 O O 2 O O O O o — 4 3 i oi 9 4 3 6 o 0 3 3 1 6 2 3 i i A ROUND- [ 123 ] A ROUND-FRONT CELLERET SIDEBOARD, Five feet long, two feet fix inches wide, framing fixteen inches deep, the front veneer’d, a deep drawer at one end prepar’d for the plumber, a plain drawer or cup- board at the other end, with one fhelf infide, a {hallow drawer in the middle, edge of the top fquare, fix plain Marlbro’ legs, and an aflragal round the bottom of the frame — — — — — — — — £■ s • d - 118 6 EXTRAS Each inch, more or lefs, in length or width — — Ditto in the depth of framing — — — - — If made with breaks at the corners of the top, and the corner legs Hand fquare, extra — - — — Ditto with eliptic front — — — — — — For the price of glueing up the top, veneering ditto, See . — See the preceding Table. If two drawers in place of a deep one, extra partition in- cluded — — — — — — — — An extra drawer above the celleret, partition included - An extra drawer in depth in the middle, partition in- cluded — — — — — — — — Sawing drawer fronts out of two-inch fluff, each cut - Ditto three-inch fluff, each cut - — - — - Glueing up ditto, at per joint - - — — - Two extra legs — — — — — — — 006 005 016 030 O 2 9 O 36 ' 0 3 9 000 000 001 026 A plain r 2 ■In Ml'*’ [ 124 I s. d. 6 £- A plain arch, veneer’d and cock beaded — — — o For the price of plate drawer, or extra work in arch — See Straight-front Celleret Sideboard Veneering deep drawer fronts, or cupboard doors infide, each — — — — — — — — o Ditto fhallow drawers, each - - — - - o Veneering each extra long drawer — — — — o Ditto each extra fhort ditto — — — — — o A loofe ciftern for bottles, to fit the fweep of the front - o Ditto when the drawer front is ftraight infide - - o A fmall ditto to wafh glaftes in - - - - o Ditto, when th'e'd rawer front is ftraight infide — - o For the price of pot cupboard, &c. — See Straight front Celleret Sideboard. Oiling and polifhing, at per foot in length — - - o 2 o o o 0 3 2 1 1 O 6 3 7 5 o 6 8 6 A SERPENTINE-FRONT SIDEBOARD TABLE, Four feet fix inches long, two feet fix inches wide, framing five inches deep, front rail veneer’d, edge of the top fquare, four plain Marlbro’ legs, and an aftragal round the bottom of the frame — - - - — 0156 EXTRAS. Each inch, more or lefs, in length or width - - o Ditto in depth of framing o ° 3 0 3 For C 125 ] £. s. d. For the price of glueing up the top, veneering ditto, &c. — See Round-front Sideboard Table. A hollow or torus round the top of the frame, fvveep part, per foot — — — — — — — — Ditto ftraight part ------- A torus moulding, with a hollow at foot — - - Ditto ftraight part — — - — - - A fmall {tone moulding on the edge of the 'l ~ top, with a veneer’d frieze, andanaftra- f wee P P" rt 11 c j • r ftraight part - gal at bottom or ditto, at per root J ox Canting the front corners of the top - — - — Rounding ditto ------- Making the ends of the top half ferpentine, and canting the corners -------- Ditto, when round corners — — — _ - Sweeping the end rails and top half ferpentine — — Veneering the end rails, when half ferpentine — — T wo extra legs _______ For the price of drawers or cupboard, &c. — See Round- front Sideboard Table. Oiling and polifhing, at per foot in length _ _ _ 003 002 005 003 006^ o o 4i 002 004 0010 010 040 010 020 002 C ©•©-3«-000© t ©' O'-©- 3 A SERPENTINE-FRONT CELLERET SIDEBOARD, Five feet long, two feet fix inches wide, framing fixteen inches deep, veneer’d front, a deep drawer at one end prepar’d for the plumber, a plain drawer or cupboard at the other end, with one fhelf infide, a {hallow drawer in the middle, fix plain Marlbro’ legs, and an aftragal round the bottom of the frame - - - - - 220 EXTRAS. [ 126 J EXTRAS. £• s. d. Each inch, more or lefs, in length or width — — -006 Ditto in depth of framing - — - — - 005 Sweeping the end rails and top half ferpentine — —080 If two drawers in place of a deep one, partition included — 029 A drawer above the celleret, partition included — —036 An extra drawer in depth in the middle, partition included o 3 9 Two extra legs - - - - - - - 026 A plain arch, veneer’d and cock beaded - - -026 A cupboard in the knee hole, with tambour front, either hollow or round, to run right and left, aftragal continued on bottom of rail — - - — — — 070 Ditto a ftraight-front cupboard — — — — — 060 For the price of a plate drawer, or extra work in arch — See Straight-front Celleret Sideboard. For glueing up drawer fronts, veneering ditto infide, and loofe cifterns — See Round-front Celleret Sideboard. For the price of mouldings on the top, &c. — See the pre- ceding Table. Oiling and polifhing, at per foot in length — - — o o 2y C <2>'>0x2>>0 ,> 0 , '0*0' , «G>''0‘ A CIRCULAR SIDEBOARD TABLE, Four feet fix inches long, framing five inches deep, the rail veneer’d, the edge of the top fquare, four plain Marlbro’ legs, and an aftragal round the bottom ot the frame - - - - — — - — 0150 EXTRAS. [ 127 ] EXTRAS. Each inch, more or lefs, in length - - - - Ditto in depth of framing - — — - - If made eliptic, extra when the fvveep of the ends is quick Glueing up the top, at per joint - — — — — Glueing up a folid top, each joint, at per foot in length — Lining up the top, at per foot in length - - - Veneering ditto, at per foot fuperficial — - - Ditto the edge, at per foot — — — — • — Corner firings on the top, at per foot — — - Rounding the edge of the top - - — - — A fmall llone moulding on the edge of the top, with a frieze veneer’d crofs-way, and an aflragal at the bottom of ditto, at per foot _______ A hollow or torus moulding round the top of the frame, per foot — — A torus, with a hollow at foot, ditto _ _ _ A drawer between the two front legs _ ~ _ Sawing out the legs, each — — — — — — Tapering ditto, each fide ______ For the price of extra work in legs, &c. — See Tables of ditto. Oiling and polifhing, at per foot in length _ _ _ £■ s. d. O o 3 O o 4 O 1 0 O o 2 O o O o 3 O o 2 o o o o 1 o o 6 o o 6 o o o o 4 o 4 o o o 1 0 o °J o o 2 A CIRCULAR [ 128 ] A CIRCULAR CELLERET SIDEBOARD, as in Plate 8, Fig. 1, £. s. d. Five feet long, the framing fixteen inches deep, two deep drawers, one prepar’d for the plumber, the other plain, a fhallow angle ditto in the middle, a cupboard in each corner, with {lielf infide, veneer’d front, four plain Marlbro’ legs, and an.aftragal round the bottom of the frame - - - - - - - - 2100 EXTRAS. Each inch, more or lefs, in length - — - — Ditto in depth of framing — — — — — — If made eliptic, extra when the fweep of the ends is quick For the price of glueing up the top, veneering ditto, &c. — See the preceding Table. Two extra legs in front — . — — - — _ Ditto in the back — — — — — — — If two drawers in place of a deep one — — — _ If without cupboards in the corners, dedudl for each - A plain arch, veneer’d and cock beaded - - — For the price of a plate drawer, or extra work in arch — See Straight-front Celleret Sideboard. A loofe cittern for bottles - — Ditto, when the front is ttraight infide - - _ A fmall ditto to wafh glafies in — — — — _ Ditto, when the front is ttraight infide — — - 006 00 5 040 040 020 029 020 026 030 026 018 o 1 6 Sawing [ 129 ] Sawing drawer fronts out of two-inch fluff, each cut - Ditto, three-inch - — — — Glueing up drawer fronts, at per joint - - - Sawing out the legs, each — — — - — Tapering ditto, each fide — — — — — — For the price of extra work in legs, dec. — See Tables of ditto. filing and polifhing, at per foot in length — — £■ O O o o o - o s. o o o o o d. Oi 0 1 1 3 COCfO'OOO'OO'O'O'.l A SIDEBOARD TABLE, with Ovalo Corners, as in Plate 8, Fig. 2 , Four feet fix inches long, two feet fix inches wide, framing five inches deep, veneer’d front, fix plain • Marlbro’ legs, and an aflragal round the bottom of the frame - — — - EXTRAS. Each inch, more or lefs, in length or width — — Ditto in depth of framing - — — — — If the corners are made eliptic, extra - - — Glueing up the top, at per joint — — — — Glueing up a folid top, each joint, at per foot in length Lining up the top, at per foot in length — — Veneering ditto, at per foot fuperficial - - - t r , - C fweep part, per foot Veneering the edge of ditto < n & & [ ffraight part, ditto - 1 o o o o o o o o o 0 0 0 2 0 4 1 0 0 2 0 °4 0 3 0 2 0 1 i 0 1 Each 4|w C *3° 3 Each corner firing, per foot — — — — — A hollow or torus under the top, per foot { ^ ^ r r Utraight part - A drawer in the middle — See Straight-front Sideboard Table. An eliptic or ferpentine middle — See ditto. Each drawer in the ovalo comers — — — — Sawing out the legs, each — — — — — — Tapering ditto, each fide — — — — — — For the price of extra work in legs, &c. — See Tables of ditto. Oiling and polifliing, at per foot in length — — — £. s. d. O O I ° O 3i 0 0 2 O46 OOl O o o£ 0 0 2 A CELLERET SIDEBOARD, with Ovalo Corners, as in Plate 8, Fig, 2, Five feet long, two feet fix inches wide, framing fixteen inches deep, veneer’d front, a drawer at one corner prepar’d for the plumber, a plain drawer or cupboard at the other, with a fhelf infide, a fhallow drawer in the middle, fix plain Marlbro’ legs, and an aftragal round the bottom of the frame — — — — — 240 EXTRAS. Each inch, more or lefs, in length or width — Ditto in depth or framing - - - — o o 6 0 5 If o C 1 3 I ] £. s. d. If the corners are made eliptic, extra — — — —020 For the price of glueing up the top, veneering ditto, See . — See the preceding Table. If an angle middle drawer, and the end drawers fquare to anfwer ditto, extra — - — — — — 020 If two drawers in the place of a deep one, extra partition in- cluded — - — — — — - — 029 A veneer’d pannel on the end of the ovalo corners, when the drawers are not the whole fize of ditto - -020 For the price of an extra drawer in the middle and arch — See Straight-front Celleret Sideboard. A loofe cittern for bottles, when the middle drawer is fquare — — — — — - — — 036 Ditto, when an angle middle drawer — — — —030 A fmall ditto to watti glattes in, when the middle drawer is fquare - — — - — _ — —023 Ditto, when an angle middle drawer — — - _ 0 1 8 Sawing out the legs, each — — — — _ 0 oi Tapering ditto, each fide — — — - — — ooot For the price of extra work in legs, &c. — See Tables of ditto . Oiling and polifhing, at per foot in length - - -003 s 2 A SIDEBOARD [ 132 ] A SIDEBOARD TABLE, with Eliptic Middle, and Eliptic Hollow on each Side, as in Plate 8, Fig. 3, Right-hand End , Four feet fix inches long, two feet fix inches wide, framing £. s. d. five inches deep, veneer’d front rails, edge of the top fquare, fix plain Marlbro’ legs, and an aftragal round the bottom of the frame — - — — — EXTRAS. Each inch, more or lefs, in length or width — — Ditto in depth of framing — — — — Glueing up the top, at per joint - - — Glueing up a folid top, each joint, at per foot in length Lining up the top, at per foot in length — — Veneering ditto, at per foot fquare — - — , r . . . r rftrainht part, per foot Veneerino; the edge or ditto i , 0 r .. 0 0 ifweep part, ditto - Corner firings in ditto, per foot - — — — A' fmall fione moulding on the edge of 3 ^ the top, with a veneer’d frieze and an ^ aftragal at the bottom of ditto, at per | c I each break loot - - - - - j A hollow or torus under the top, per foot {^ wce P P ait 1 r [ltraight part A drawer in the middle - - _ _ _ If two in the length, including partition - - Each eliptic end drawer — — _ _ _ Sawing out the legs, each — — _ - 1 4 6 — 0 0 3 — 0 0 3 t — 0 0 2 — 0 0 of — 0 0 3 - 0 0 2 — 0 0 1 — 0 0 2— 1 2 — 0 0 1 — 0 0 7 — 0 0 4 i — 0 0 5 — 0 0 3 i — 0 0 2 — 0 4 0 - 0 7 0 — 0 4 0 — 0 0 1 Tap tering [ 133 ] £. s. d . Tapering ditto, each fide - — - *- — — 0007 For the price of extra work in legs, &c . — See Tables of ditto. Oiling and polifhing, at per foot in length - - -002 C •0oO.'0<>0'>0' 3 A CELLERET SIDEBOARD, with Eliptic Middle, and Eliptic Hollow on each Side, as in Plate 8, Fig. 3, Right-hand End , Five feet long, two feet fix inches wide,' framing one foot four inches deep, veneer’d front, edge of the top fquare, a deep drawer at one end prepar’d for the plumber, a plain drawer or cupboard at the other end, with a fhelf infide, a (hallow drawer in the middle, fix plain Marlbro’ legs, and an aftragal round the bottom of the frame —290 EXTRAS. Each inch, more or lefs, in length or width - — — Ditto in depth of framing For the price of glueing up the top, veneering ditto, &c. — • Sec the preceding Table. If two drawers in place of a deep one, partition included — An extra drawer above the celleret, partition included — An extra drawer in depth in the middle, partition included Sawmg drawer fronts out of two-inch fluff, each cut - Ditto three-inch fluff, each cut — — — — - 006 005 030 040 0 4 9 000 000 Glueing to |t [ i34 1 d. £■ Glueing up ditto, at per joint — — - — — o A plain arch, veneer’d and cock beaded — — — o For the price of a plate drawer, or extra work in arch — See Straight-front Cellerct Sideboard. Veneering each extra drawer above the celleret — — o Ditto each extra long drawer — — — — — o Veneering deep drawer fronts, or cupboard door infide, each o Ditto fhallow drawers, each — — — - — o A loofe ciftern for bottles to fit the fweep - — — o Ditto, when the drawer front is ftraieht infide - — o A fmall ditto to wafh glafifes in to fit the fweep — — o Ditto when the drawer front is ftraight infide — — o Oiling and polifhing, at per foot in length — — - o S. o 3 o o o 0 3 2 2 1 O 1 o 6 8 7 4 6 6 o 6 3 C 0<3>'<2>->0‘'0-<3>-<3K5><0“0' 3 A SIDEBOARD TABLE, with Eliptic Middle, and Ogee on each Side, as in Plate 8, Fig 3, Left-hand End , Four feet fix inches long, two feet fix inches wide, framing five inches deep, veneer’d front rails, fix plain Marlbro’ legs, and an afiragal round the bottom of the frame - - - - - - - -160 EXTRAS. Each inch, more or lefs, in length or width — — —003 Ditto in depth of framing - - - — -005 Glueing I >35 ] Glueing up the top, each joint - - — - Glueing up a folid top, each joint, at per foot in length Lining up the top, at per foot in length — — Veneering the top, at per foot fquare — — — Veneering the edge of ditto, at per foot f fweep part \ ftraight part Each comer firing, per foot - — A fmall ftone moulding on the edge of"] the top, with a veneer’d frieze, and an [ aftragal at the bottom of ditto, at per j" foot _____ j Each break — — — — fweep part flraight part A hollow or torus under the top, at per foot [ fweep part — \ flraight part A drawer in the middle — — — — — — If two in the length — — — — — — — Each end drawer — — — — — — — Sawing out the legs, each — — — — — Tapering ditto, each fide _ For the price of extra work in legs, &c. — See Tables of ditto. Oiling and polifhing, at per foot in length — £. s. d. 0 0 2 O O O^ 0 0,3 0 0 2 0 O l£ 0 0 1 001 008 o o 4J 005 004 002 o 4 .0 070 0 4 9 001 o o oA 002 A CELLERET [ 13 ^ ] A CELLERET SIDEBOARD, with Eliptic Middle, and Ogee on each Side, as in Plate 8, Fig 3, Left-hand End , £• s- d. Five feet long, two feet fix inches wide, framing one foot four inches deep, veneer’d front, a deep drawer at one end prepar’d for the plumber, a plain drawer or cupboard at the other end, with a fhelf infide, a ihallow drawer in the middle, fix plain Marlbro’ legs, and an aftragal round the bottom of the frame - - — - — 2150 EXTRAS. Each inch, more or lefs, in length or width — — -00 Ditto in depth of framing — — - — — o O For the price of glueing up the top, veneering ditto, &c. — See the preceding Table. If two drawers in place of a deep one, partition included —02 A drawer above the celleret, partition included — —04 An extra drawer in depth in the middle, partition included o 4 Sawing drawer fronts out of two-inch fluff, each cut —00 Ditto three-inch fluff, each cut — — — — — o o Glueing up ditto, each joint — — — - —00 Veneering each drawer more than three in front - -01 Veneering deep drawer fronts, or cupboard door infide, each o 1 Ditto fhallow drawers, each — — — — —00 A plain arch, veneer’d and cock beaded - - . -03 For the price of extra work in ditto — See Straight-front Celleret Sideboard. 6 6 9 9 6 o 0 1 o o 5 o A loofe -Hw w|* [ >37 ] £■ s. d. A loofe cifiern for bottles to fit the fweep - - —050 A fmall ditto to vvafh glafies in — — — -030 Oiling and polifhing, at per foot in length - - -003 C-0>Ok^>Ok2>’>0'K2> > 0' > 0' < 2>3 A SIDEBOARD TABLE, with Hollow Middle, and Astragal on each Side, as in Plate 8, Fig . 4, Four feet fix inches long, two feet fix inches wide at the afiragal part, framing five inches deep, veneer’d front rails, fix plain Marlbro’ legs, and an afiragal round the bottom of the frame — - — — — -150 EXTRAS. Each inch, more or lefs, in length or width — - Ditto in depth of framing — - - — — If the fweeps are eliptic — Glueing up the top, at per joint — — - — Glueing up a folid top, each joint, at per foot in length - Lining up the top, at per foot in length — - - Veneering the top, at per foot fquare — — — - Veneering the edge of ditto, at per foot Corner firings in the top, at per foot - T i fweep part l ftraight part 003 004 016 002 000^ 003 002 0 o 1 ± 001 O O I A fmall [ >3 8 ] £. s. d. A fmall ftone moulding on the edge of the " 1 top, with a veneer’d frieze, and an aftragal at the bottom of ditto, at per foot — Each break - — — - — — fweep part ftraight part A hollow or torus under the top, per foot r fweep part 1 ftraight part A drawer in the middle — — — — — — Each end ditto — — — — — — — Sawing out the legs, each ■— — — — — Tapering ditto, each fide — — — — — — For the price of extra work in legs, See. — See Tables of ditto. Oiling and polifhing, at per foot in length — — — 007 o o 4% 00 5 0 o 3i 002 040 0 3 9 001 000^ 002 A CELLERET SIDEBOARD, with Hollow Middle, and Astragal on each Side, as in Plate 8 , Fig . 4 , F ive feet long, two feet fix inches wide at the aftragal part, framing fixteen inches deep, veneer’d front, a drawer at one end prepar’d for the plumber, a plain drawer or cupboard at the other end, with a fhelf infide, a fhallow drawer in the middle, fix plain Marlbro’ legs, and an aftragal round the bottom of the frame - - 2 100 EXTRAS. EXTRAS. Each inch, more or lefs, in length or width - - Ditto in depth of framing - — — — If made with eliptic fweeps _ _ _ _ — For the price of glueing up the top, veneering ditto, &c.~ See the preceding Table. If two drawers in place of a deep one, partition included An extra drawer above the celleret, partition included — An extra drawer in depth in the middle, partition included When a fquare is left on the ends of the drawers to form a part of the break — — — — — — Sawing drawer fronts out of two-inch fluff, each cut — Ditto, three-inch — — — — — — — Glueing up ditto, each joint — — - — — A plain arch veneer’d and cock beaded, when circular hollow — — — — — — Ditto, when eliptic hollow — — — — — For the price of plate drawer, extra work in arch, &c.— ■ ■* See Straight-front Celleret Sideboard. Veneering each extra drawer above the celleret — — Ditto each extra long drawer — — — — _ Veneering deep drawer fronts or cupboard door infide, each Ditto (hallow drawers, each — — — _ „ A loofe ciftern for bottles to fit the fweep - — ^ A fmall ditto to wafh glaffes in — _ _ — Oiling and polifhing, at per foot in length — £■ s. d. O o 6 O 0 5 o 3 o o 3 o o 4 o o 4 9 0 4 o o o o 0 °4 o o 1 o 2 6 o 3 o o o 7 o o 8 o o 7 O o 4 o 3 o o l 8 o o 3 T 2 A SIDEBOARD [ M° ] A SIDEBOARD TABLE, with Eliptic Middle, and Hollow on each Side to the Back, as in Plate 8, Fig 5, Right-hand End , Five feet long, two feet fix inches wide, framing five inches deep, veneer’d rails, edge of the top fquare, four plain Marlbro’ legs, and an aftragal round the bottom of the frame — — — — — — — — £. s. d. 160 EXTRAS. Each inch, more or lefs, in length or width — — Ditto in depth of framing — — — — — If made with two lliort end rails, tenon’d into the back legs, and dovetail’d into the end of the hollow rails, as in plate 8, fig 5, left-hand end -- — — — — Two extra legs, when ditto - - - — — A drawer in the middle part — — — — — Glueing up the top, at per joint — — - — — Glueing up a folid top, each joint at per foot in length — Lining up the top, at per foot in length - - _ Veneering the top, at per foot fquare — - — - Veneering the edge of ditto, at per foot - - — Each corner firing, per foot - — — _ — A fmall flone moulding on the edge of the top, with a ve- neer’d frieze, and an aflragal at the bottom of ditto, at per foot - _ Each break - — — — _ 00 3 004 0 2 0 0 2 0 O4O 0 0 2 OOO 003 0 0 2 0 O lj- 001 007 005 A hollow [ 141 ] £■ s. d. A hollow or torus under the top, per foot — - - O 0 3 j Sawing out the legs, each — — — — - - 0 0 1 Tapering ditto, each fide _ _ — — - - O 0 0 i For the price of extra work in legs, &c. — See Tables of ditto. Oiling and polifhing, at per foot in length - - -002 CO©"© 0”<2>''<2»‘<2>' , <2>"' > 00 A pedestal, Three feet two inches high, one foot four inches fquare, a fiat pannel’d door in front, a moulding on the edge of the top, on fall plinth — — — — — o lO 6 EXTRAS. Each inch, more or lefs, in length, width, or height — A drawer at the bottom for a heater within the door — Ditto when fix’d to the plinth - - - - - Lining the infide of the pedeftal with tin — — - Ditto, when a drawer ______ Each fingle rack for plates, with fquar^ bars, or the front and back rails notch’d — — — — — — Each double ditto - — — — - — — If the bars in the racks are cut out to fit the plates, each fingle rack extra ______ Covering the bars with baize or leather, each fingle rack — Ditto, each double rack ______ A celleret drawer at the bottom prepar’d for the plumber, or a plate drawer lin’d with baize infide of the door - 003 o 1 3 020 030 040 026 040 010 o 1 3 02 6 036 Making [ n 2 ] Making tt'.c front plinth to draw out with the celleret drawer - - - - ” Putting on rollers, each pair - — Each plain drawer infide, fcratch beaded Each inch more than feven in depth of ditto Each partition — — — Lining each ditto crofs-way — — A ihelf in the top for a pot _ _ _ - A plain door to ditto, hing’d to fall down — — — Square clamping ditto — Miter clamping ditto, each miter extra - A reed or tambour door, with inner end to conceal ditto Each drawer above the door - - - - - Glueing up the ends, at per joint — — — — Ditto the top or drawer fronts — - — — — Lining up the top — — — - — Veneering the top _______ If veneer’d in quarters ftraight-way _ — _ _ Ditto crofs-way _______ A fmall ftone moulding on the edge of the top, with a veneer’d frieze and an aftragal at the bottom of ditto, at per foot — — — — — — — Veneering the ends, each — — — — — Each joint in ditto, at per foot — - — — Framing the ends with one fiat pannel, each end - - Ditto with two pannels ______ Veneering the framing ftraight-way when one pannel, each frame — — Ditto crofs-way — — _ _ _ _ Veneering the framing ftraight-way, when two pannels - £■ s. d . O 1 o O o 3 o 1 8 o o 1 o o 5 o o 1 o o 5 o 1 2 o o 4 o o 4 0 2 6 o 2 o o 0 1 o o °i o o 4 o 0 6 o X o o 1 6 o o 4i o o 9 o o o 2 o 0 3 o o 0 10 o I 4 0 1 i Ditto, C M3 J £■ Ditto, when the middle rail is miter’d at the comers - o If crofs-way - — — — - — - O Veneering each pannel — — — — — — o If two in a frame, extra — — — — — — o Veneering: each drawer front — — — — — O French feet, or folid French brackets — — — — O Veneering: each fide of French brackets — — — O Plain taper flump feet the fame as a plinth. A loofe frame for the feet — — — — — o An aftrag:al on front and ends of the carcafe above the doors o For the price of pilafters — See Straight-front Library. Round front, with the pannel bent in — — — o If made eliptic, extra — — — — — — o Each round-front drawer above the door — — — o A round-front celleret drawer infide the door — — o A reed or tambour door to a pot cupboard in a fweep front o For the price of loofe ciflerns : — See Straight or Round-front Celleret Sideboard. Fram’d back, each pannel — — — — - — o Oiling and polifhing — — — — — — o s. d. 1 7 2 1 ° 9 o 3 ° 5 2 O 0 2 1 O o 6 5 6 2 O 2 6 4 6 2 6 o 6 ° 9 A plain Square Plinth for a vafe to fta'nd on, the edge and top of ditto veneer’d, the veneer on the top miter’d - o 2 0 A plain cove plinth miter’d, the top veneer’d — - o 6 0 Veneering the cove — — — — — - o 3 o Each corner firing in a fquare plinth — — — - o o 1 Ditto on the foot of a cov’d plinth — — — - o 0 1 Ditto up the corners of the cove — — — - o o 3 Veneering the cove crofs-way, each fide extra — - o 1 o A VASE, [ >44 ] A VASE, (glued up for the turner) twelve joints in ditto, with a folid top and bottom - — — — — Each extra joint Each joint in the top of the vafe _ _ _ _ Ditto in the bottom of the vafe - - - — Glueing up the top or bottom of the vafe in thickneffes, each joint _ — — — — - — - A fquare cov’d bottom ------ Veneering the vafe, twelve joints in ditto, with or without a firing, each joint ------ Each extra joint _______ If the firings up the joints are continued into the frieze with circular tops to ditto, each joint extra — - Putting in a tongue of wood or brafs on the top edge of vafe, the groove for ditto to be prepar’d by the turner Veneering the frieze at the top of the vafe — — _ Putting in quarter fluff for fluting, the turner to prepare the groove for ditto ______ For the price of fluting — See Table of ditto . An aflragal round the top and bottom of the frieze long- way, each _______ Ditto crofs-way, the turner to prepare the groove and work the moulding A triple firing round ditto, each _ _ _ _ Putting fluff for a moulding in the body of the vafe, the turner to prepare the groove and work the moulding - Fixing the vafe to the pedeflal - _ _ _ _ Oiling and polifhing ditto _ _ _ _ _ £. s. d. 060 006 004 004 003 036 o o 9 009 003 006 0 12 0 1 9 Ol 6 010 009 Ol6 010 006 A DINING C 145 ] A DINING TABLE, £. s. d. With one or two flaps to ditto hung with rule joints, or fquare ditto with tongues, four plain Marlbro* legs, one fly on each fide, the length and width added together, at per foot — — — — — — — — 010 EXTRAS. Each extra rule joint in a rail — - — — - Each extra fix’d leg, including the crofs rail — — — Each extra fix’d leg in a fhip table - - — — Four low rails fram’d in, the fize of the feet — — Rounding the corners of the flaps, each comer — — Sweeping the flaps either ferpentine or circular, each — Making the top oval — — — — — — Aftragal on the bottom of the frame, when the legs are flufh ________ Each extra miter when the legs project _ _ _ Scolloping the end rails ______ Veneering ditto long- way _____ Ditto the back or joint rails, each _ _ _ _ If crofs-way, each joint extra _____ Veneering the bed or flaps, per foot fquare - - _ Veneering the edge of ditto crofs-way , at per foot — - Crofling each joint — — — Rounding the edge of the top, at per foot — - — Working an aftragal or hollow and two beads on the edge of ditto, at per foot ______ * u 009 010 008 020 O O 2j 0 0 6 O 1 3 0 0 6 o o of 003 006 0 o 4 001 002 0 o 1 001 O o of 0 0 2 Ditto, [ ] Ditto, when oval or circular top — — - — - Ditto, when Terpentine — — — — — Sawing out joint rails, each - — — — - Ditto each leg - — - — — — — Tapering ditto, each fide — — — — — — If fquarc joints without tongues, dedud; each joint — For the price of extra work in legs, &c. — See Tables of ditto. If only one of the above tables, and not to join to any other, to be extra — — — — — — — Each joint in a fet of tables that fhifts with ftrap hinges or faftenings, to be counted when the whole fet is together Each extra fpring, plate, or bolt - - — — Oiling and polifhing, at per foot on the bed - — — £. s . d . O o ° o 3 O O I O O o O O o 006 010 O 1 G 003 0 0 2 A HALF-ROUND DINING TABLE, EXTRAS. Each incn, more or lefs, in length Each extra fix’d lesr - - — _ A flap, with one fly leg to ditto — — Each inch, more or lefs, in length of the flap A fly rail, with one rule joint, when no flap — Each extra rule joint in ditto _ _ _ Sweeping the flap half round _ A.n afhagal tound the bottom of the rail, when flufh - - _ 0 11 0 _ 0 0 2 • — - 0 0 8 — - 0 3 0 — - 0 0 1 — - 0 1 3 — — 0 0 9 legs are 0 0 6 — 0 0 9 Each to | •— « 4^Jco [ 147 ] Each extra miter when the legs project - Cock-beads under the rails between the legs - — - Ditto groov’d into the legs, when they project, each leg, if not miter’d — — — — — — — Three low rails, framed in, the fize of the legs, for fhip ufe Scolloping the lower edge of the rail — — — — Veneering the top or flap, per foot fquare - — - Veneering the edge of top crofs-way, at per foot - — Rounding the edge, at per foot — — — - - Working an aftragal or hollow and two beads on the edge of ditto, at per foot - — - — — - Oiling and polilliing the bed, at pet foot in length - - Ditto the flap, per foot - — — - — — £. s. d. o O ° ° 9 o o 1 0 2 6 o o 0 0 2 0 0 1 O O O 0 0 2 ^ 0 0 1 o o o4 A FLAP, four feet long, with one fly leg, and two ditto fix’d to a rail hinged to the under fide of the flap - o Each inch, more or lefs, in length — — — — o An extra fly leg - - — — - — - o Rounding the corners of the flap, each corner — — o Cutting ditto half round — — - — — - o Oiling and polifhing, at per foot in length - - - o 6 0 0 1 1 5 O 2i o 6 o 1 A FLAP, four feet long, a top to ditto three inches wide, hung with a rule joint to the flap, two fram’d brackets to fupport ditto, to fix againft a wall — — — Each inch, more or lefs, in length - - - - If rule joint brackets as a Pembroke table, dedudt - - Each leg to ditto ------- U 2 o 6 o o o i o i o o o 6 A fquare tJ [ 148 ] £. s. d. A SQUARE SLAB to lay on the furbafe, with plain lquare edge, per foot fuperficial — — — — — 002 Sweeping the front of ditto, circular or eliptic, per foot in length — — — — — “ ~ — OOl Sweeping ditto ferpentine, per foot in length - - - O O i£ For the price of other extra work — See Sideboard Table. C>0 l 0*£>-‘00 , 0 > 0'0'<2X'SO A HORSE-SHOE DINING TABLE, as in Plate 9, Fig, 2, Seven feet long in the bed, tw’o feet fix inches wide, veneer’d rail, the flaps to fold on the top, fupported either way, (when open) as fhewn in fig. 1, plain taper legs, and an aftragal round the bottom of the rail — — 220 EXTRAS. Each inch, more or lefs, in length or width - — — Each extra miter in the aflragal when the legs projecft - Working an aflragal or hollow and two beads on the edge of the top, at per foot - — — — Sawing out each leg ______ For the price of extra work in legs — See Tables of ditto. Oiling and polifhing 004 o o o§- 002 000 016 A PILLAR. [ 149 3 A PILLAR-AND-CLAW DINING TABLE, £• s - d. Four feet long, two feet wide, folid block fcrew’d to the top, three claws, as No. 1, Table of ditto, with plate on the bottom - — — — — — — O 9 O EXTRAS. Each inch, more or lefs, in length or width — — — An extra claw — — — — — — — Sawing out each claw — — — — — — Making the top to turn up with Angle clamps and double catch — — — — — — — — Ditto with double clamps, fram’d — — — — Cutting the top half round ~ — - — — A flap to ditto, twelve inches wide, fupported by two lopers — — — — — — — — When the lopers are made to run in a box, each loper extra Each inch, more or lefs, in length or width of the flap - For the price of joining with flrap hinges or faftenings — See Dining Table. Veneering each top or flap, at per foot fquare — - fweep part - flraight part — Each corner firing on ditto, at per foot — - — An aftragal or two beads and hollow on the edge of the top, at per foot ------- Ditto on a circular top ------ Veneering the edge of the top, at per foot^ 001 016 002 010 020 00 6 036 003 001 002 o o i\ 0 O I 001 0 0 2 O O 2j Each £• s. d. [ 15° 3 Each frame, three inches deep, fix’d on the under fide of the top, w ith two fly brackets on each fide to fupport the flaps - - — - ~ “ “ " 0 5 6 Each fly, more or lefs — — - — — — 006 For the price of glueing up and veneering the block — See Loo Table. For extra work in claws — See Table of ditto. Oiling and polifliing each table, add the length and width together, at per foot — — — — — — 001 A LOO TABLE, Four feet diameter, fquare edge to the top, or faint rounded, Angle clamps and double catch, folid block, three claws, as No. 1, Table of ditto, with plate on the bottom - oil o EXTRAS. Each inch, more or lefs, in length or width — - — o If under three feet fix diameter to be reckoned as a Pillar and Claw Table. An extra claw - _ _ _ — o Sawing out the claws, each — — — - — o Glueing up the top, at per joint — — - — — o Each joint in a folid top, per foot in length - — - o Letting in dovetail pieces to fecure the joints, each - - o Veneering the top, per foot fuperficial — — — — o Each joint in the veneer, per foot in length - — - o Lipping the top for cloth, fet againfl: cleaning up. Veneering the edge of the top, at per foot - - _ 0 o 1 1 6 o 2 o 1 o o O I O 2 O 2 O \\ Each ■Hw [ 15 - ] £■ ’■ Each corner firing, per foot - — - — - o o A firing between the band and cloth, per foot - - o o Sinking a folid top for cloth to die off gradually from the margin — — — — — — — oi An aflragal or two beads and hollow on the edge of the top, at per foot - — — — — — — — oo Letting in each difh, when turned — — — — o o A lipping round each difh - — — — - o o Working out each difh — — — — — — o i Lining the top, when plain — — — — — o i Ditto when difhes, each difh extra — — - — o o Glueing up a block in two thickneffes, not exceeding twelve inches fquare — — - — — — - o O Each extra two inches each way - — — — O o When glued up in three thickneffes, add half the above price. Veneering a block twelve inches fquare and under — — o o Every three inches extra each way - - - — o o Oiling and polifhing, when a lin’d top - - - o o Ditto, when folid or veneer’d — — — — _ o o C>0>©»©o0>0'<2>*©*®*0>©0 A PILLAR- AND-CLAW TABLE, Two feet three inches diameter, folid block, edge of the top fquare, or faint rounded, three claws, as No. i, Table of ditto, with plate on the bottom - - -05 d. l q— ^ 2 4 6 o 3 3 4 3 oi 4 9 6 EXTRAS. L 1 5 2 J EXTRAS. £. s. L Each inch, more or lefs, in diameter - - - -002 If above three feet fix inches in diameter to be reckoned as a Loo Table. Sawing out each claw — — — — — — o Glueing up a folid top, each joint, per foot — — — O Ditto to veneer on, each joint — — — — — o Veneering the top, per foot fuperfkial — — — — o Each joint in the veneer, per foot in length - — — o If veneer’d in quarters, each joint — - - — o Veneering the edge of the top, at per foot — — — o Each corner firing on ditto, at per foot — — — o Aftragal or hone moulding on the edge of the top, per foot o Double catches, extra _ q For the price of extra work in claws — See Table of ditto. If only one of thefe, extra — — _ _ Oiling and polilhing o 1 O o o 1 o 2 o 2 o 6 o li o 1 O 2 y O 3 o 6 o 4 C kc>'Oh2>*oo>»0^>©-kSx*0' 3 A LADY’s WORK STAND, All folid, two feet fix inches high, top one foot four inches Iquare, on three claws, as No. 1, Table of ditto 030 EXTRAS. Each inch, more or lefs, in length or width Making the top to turn up with clamps If the top is made o&agon or round - - o o of -00 9 -004 Ditto t '53 J Ditto oval ------- Working an aftragal on the edge of a fquare top - Ditto otftagon — — — — — — Ditto oval - — — — - — — Veneering the top ------ Sawing out each claw - - - - - Ditto the pillar ------ An ogee ftuck round block, extra _ _ — If a fingle one, to be extra — - - - For any other work — See Tables of ditto. Oiling and polifhing _____ No. I. A LADY’s DRESSING TABLE, Two feet three inches long, one foot five inches wide, framing five inches deep, a flat top to ditto, fupported by a flay, a glafs frame hing’d to a hiding piece, fupported by a horfe, four loofe covers infide, plain Marlbro’ legs, and an aftragal round the bottom of the frame - — o 13 o EXTRAS. Each inch, more or lefs, in length or width — — O O 24 - Ditto in depth of framing — — — — —003 Ditto when veneer’d rails — — - — — o O 3y Glueing up the top, either folid or to veneer on, at per joint 001 Square clamping the top - - - - - -006 x Miter £■ s - d. -005 -O06 - o o 10 -010 -004 -OOI - o o of -008 -006 -002 [ 154 1 £■ s. Miter clamping ditto, each miter extra — — — o o Veneering the top, per toot fquare — — — — o o Each joint in the veneer, per foot in length - - - o o Veneering the front or back rail, each — . — — O o Ditto each end rail — — - “ “ — OO An aflragal or flone moulding on the edge of the top, or veneering ditto crofs-ways, with a firing in the upper corner, per foot — — — — - — OO A firing in the lower corner of the top, per foot - - o o Sweeping the top ferpentine all round, when a fquare frame o o If made with a round front, extra from flraight - - o 2 Ditto eliptic, the legs to form the break - - -03 Ditto ferpentine - — — - — — — 03 Ditto, when the end rails are half ferpentine - -07 An allragal, hollow and two beads, or flone moulding on the edge of a ferpentine top, per foot — — — o o Veneering the edge of a ferpentine top, per foot — — o O Veneering ferpentine front rail — — — — _ 0 o Ditto end rails, each - - — — - — 00 A flat tea-chefl top, miter dove tail’d, or the front veneer’d, extra from common flat top - - - - —03 Making ditto round front, extra - - — -01 Making ditto ferpentine, extra from flraight - —01 A fpring quadrant to fupport the top in lieu of a flay -00 Sawing out the legs, each cut — - — — — 00 Tapering ditto, each fide - - _ — —00 If a fingle foot to fupport the glafs, in lieu of a horfe, dedudl — - — — _ — — — OO For the price of fhelf or flretcher — See Pembroke or Ri - fing-top Writing Table. d. 6 2 2 3 2 2 1 9 o o 6 o 3 6 4 o o 6 6 o o 6 For ■|m Hn [ 1 55 3 £■ s - d ■ For the price of extra work infide — See Furniture Drawer. Oiling and polifhing — - - - - - 006 c >0(^K‘0*0^2> 3 No. II. A LADY’s DRESSING TABLE, Two feet fix inches long, one foot fix inches wide, framing .j. five inches deep, a glafs frame hing’d to a Hiding piece, and fupported by a horfe, four loofe covers infide, fold- tops, miter dove-tail’d, plain Marlbro’ legs, and an aflra- gal round the bottom of the frame — — — O 19 o EXTRAS. Each inch, more or lefs, in length or width — Ditto in depth of framing — — — _ Ditto, when veneer’d rails — — _ — Each long drawer, cock beaded or fining - — Each fiiort ditto — - — — — — If fram’d with inner ends to form a knee hole, extra A plain arch, cock beaded — — — — A plain fiider, fquare clamp’d — — — — Veneering each long drawer front — — — Ditto each fiiort - — _ If crofs-way, each joint extra — — - _ For veneering the rails — See No. 1. Veneering the rails in the knee hole, each - x 2 — 0 0 — 0 0 3 — 0 0 3t — 0 2 3 — 0 I 9 — 0 3 0 — 0 1 0 - 0 1 6 — 0 0 5 — 0 0 3 — 0 0 1 — 0 0 3 When [ 156 ] £. s. d. When made with three tops, the middle one hing’d to the back, extra from folding tops - — - - Veneering the tops, each — — — — — Veneering the fronts of ditto, fet againft miter dove-tailing. Corner firing round ditto, per foot — — — — Each joint rail in the ends to fupport the tops — — Hinging the tops with HL hinges - — - — Making the above round front, when without drawers - Ditto, when three tops — _ — — Each long drawer in ditto, cock beaded - — — Each fhort ditto — — — A plain arch, cock beaded — — — _ _ Veneering each long drawer front — — _ _ Ditto each fhort ditto — — Making ditto ferpentine front, when without drawers — Each long drawer in ditto, cock beaded - _ _ Each fhort ditto _______ Veneering each long drawer front _ _ _ Ditto each fhort Sawing out the legs, each cut _ _ _ _ _ Tapering ditto, each fide _____ ff a fingle foot to fupport the glafs in lieu of a horfe, de- dud: _______ lor the price of extra work infide — See Furniture Drawer. Oiling and polifhing ______ o 3 o 004 o o 1 o I 3 010 040 050 O 2 9 0 2 0 o 1 6 007 004 060 0 3 3 023 0010 006 000 000 006 009 No. III. H" W|' L *57 ] No. III. A GENTLEMAN’S OR LADY’s DRESSING TABLE, £. s. d. Two feet nine inches long, one foot eight inches wide, framing fifteen inches deep, four real drawers and five fham ditto in front, cock beaded, a flap top, fupported by a quadrant, the edge of the top moulded or veneer’d crofs-way, and a firing in the upper corner, plain taper legs, and an aflragal round the bottom of the frame, a glafs frame hing’d to a Aiding piece, fupported by a horfe, and four loofe covers infide — — — — 1130 EXTRAS. Each inch, more or lefs, in length or width — - Ditto in depth of framing - — - - - A flat tea-chefl top, miter dove-tail’d, or the front veneer’d, extra from flap top with moulded edge — - — A flap infide ditto, fquare clamp’d - - - - Veneering the front ______ Ditto the top, per fquare foot - _ - - _ Veneering each end rail - — — — Ditto the back rail — — — — — — — Making the above round front, with a flap top, extra - Veneering round front ------ A flat tea-chefl top to ditto, miter dove-tail’d, or the front veneer’d, extra from flap top with moulded edge - A flap infide ditto, fquare clamp’d _ _ _ _ 009 003 023 0 1 9 026 002 004 006 090 0 3 3 0 3 3 o 2 3 Making - O t x 5 8 ] Making ditto Terpentine, with a flap top - - - Veneering the front, when Terpentine - - - A flat tea-cheft to ditto, miter dove-tail’d, or the front ve- neer’d, extra from flap top with moulded edge — — A flap inflde ditto, fquare clamp’d - — - — Corner firings, per foot ------ Two fvving-glafs frames to Aide between the ends, and turn on brafs collars, as in Plate g, fig. 4. — — Making them to rife with weights, each pair — - Carting weights, each pair - - - — - If made with a knee hole, for extra framing — — Each fhort drawer when ditto - - - — — Veneering ditto, each ______ Each fliort drawer, when round or Terpentine front — Veneering ditto, each — — Plain arch, cock beaded - — — — — _ Ditto, when Terpentine or round front — ~ — For the price of extra work — See Furniture Drawer or Harlequin Table. Oiling and polifhing - — £. s. d. o 14 6 040 036 026 O O I 100 o i 6 006 030 020 004 026 005 o 1 3 020 010 A LADY’s DRESSING STAND, as in Plate 7, Fig. 4. One foot eight inches fquare, folding tops miter dove- tail’d, and two drawers, three fham ditto in front, a fquare bidet at one end fupported by two drop feet, a glafs frame hing’d to a Aiding piece, fupported by a horfe, and four loofe covers inflde, plain taper legs, and an artragal round the bottom of the frame - _ _ 1 z 0 0 EXTRAS. [ '59 ] EXTRAS. Each inch, more or lefs, in length or width - - Fitting up a drawer for a bafon and two cups - - A hollow round the infide of ditto — — — — A ciftern behind to receive the water from the bafon drawer Mitering pieces on the top of the bidet to receive a fweep’d If ditto is fram’d inftead of miter’d, extra — - — Sweeping the upper part of the drawer Tides to the fhape of the pan — — — — — — — Lopers to bidet or drawer ______ Veneering the front ______ Ditto the ends or back, each — — — — — Making ditto round front, extra — _ _ — Ditto ferpentine — — — Veneering round front ______ Ditto ferpentine _______ Veneering the tops — — — — — — — Veneering the fronts of ditto, fet againfl miter dove-tailing. Corner firings, per foot ______ If a fingle foot to fupport the glafs in lieu of a horfe, dedud ________ For the price of extra work infide — See Furniture Drawer. £. s. d. 004 o 1 3 O I o 030 o i 6 006 006 030 020 O O Q 0 8 0 0 12 0 0 3° 040 007 001 0 0 6 Sawing out each leg - - _ - _ — o o 0-s- oiling and polifhing - - - - - -008 A GENTLEMAN’S [ 160 ] A GENTLEMAN’S DRESSING STAND, as in Plate 3, Fig . 2, £. s. d. One foot ten inches long, one foot eight inches wide, five drawers in front, and two fham ditto, the drawers fitted up as follows — one for a night ftool, one for a fquare bidet to take out of the carcafe and fiand on four fly feet, one for a bafon and two cups, one for a water bottle, the other empty, a glafs frame hing’d to a Aiding piece fup- ported by a horfe, and four loofe covers infide, a tea-cheft top miter dove-tail’d, plain taper legs, and an aftragal round the bottom of the frame — — — —230 EXTRAS. Each inch, more or lefs, in length or width — — A hollow round the infide of the bafon drawer - — When a fweep’d bidet pan — See Lady's Drcjfmg Stand. A flap infide the top fquare clamp’d - - - - Miter clamping ditto, each miter extra - - - Veneering the front — — Ditto the ends or back, each — - - _ _ Ditto, the top - — — Each joint in the veneer of the top - _ _ _ Ditto in the back or ends - _ _ _ _ Veneering partition edges afkew or crofs-way, per foot extra Ditto with king, tulip, or any other hard wood, at per foot 004 OlO o 1 6 006 026 009 006 004 003 O O Oj O O I Making [ 161 ] Making the above round front — — — - - Ditto eliptic, extra — — — — Each break formed by the legs — - — — — Making the front ferpentine — — — — - Veneering a round front — — — — — — Ditto a ferpentine front - — — — — - Each corner firing, per foot — - - - If a fingle foot to fupport the glafs in lieu of a horfe, dedudt — — — — — — — — A glafs frame infide the top (no partitions) — — - A flap on each fide of ditto when a ftraight front, lock’d and hing’d, including partitions — — - - Ditto, when a round or ferpentine front - - — For the price of extra work infide — See Furniture Drawer. Oiling and polifhing ______ £. s. d. 090 020 010 0 13 o 036 046 001 006 026 030 036 0 0 9 C0 > <2>"€»0 , 0'0 < 0©'3 A RUDD, or LADY’s DRESSING TABLE, as in Plate 1 1 , Fig. 1 , Th ree feet four inches long, two feet wide, three drawers in front, the end ones to turn out on centres, a glafs frame hing’d to each end drawer, and fupported by quadrants, a moulding on the edge of the top, plain Marlbro’ legs, and an aftragal round the bottom of the frame —300 Y EXTRAS. [ 162 ] EXTRAS. Each inch, more or lefs, in length or width Ditto each inch above nine in depth of framing Glueing up the top, at per joint - - Clamping the top crofs-way to appear as folid Veneering the top, per foot fquare — ~ Each joint in the veneer, per foot in length - Veneering the front ftraight-way Ditto the end rails, each — Crofs-way, each joint extra _ — — — — If made with two extra fhort drawers to form a knee hole, partitions included — — Veneering the front when a knee hole Veneering the inner rails when a knee hole - - - A plain arch cock beaded - - - - For the price of extra work in arch — See Straight-front Celleret Sideboard , Quadrant boxes to the end drawers - - - - If made with around front, without a knee hole - - Ditto ferpentine Making ditto round front, when a knee hole — — — Ditto ferpentine — Sawing out the legs, each _ _ - — - Tapering ditto, each fide ------ Fixing the legs with iron fquares, orfcrews and plates — For the price of work infide the drawers — See Furniture Drawer £■ s. d. O o 6 O 0 6 O o i o o 9 o 0 2 o 0 2 o 1 10 o o 4 o o i o 8 0 o 2 8 o 0 6 o 1 3 o 5 O o 9 o o o o x 3 o o *9 o o 0 0| o 0 Oj o 2 o Oiling and polilhing — - — - - - oio A RUDD [ 163 1 A RUDD DRESSING CHEST, £\ s. d. Three feet fix inches long, three fiiort drawers and glafs frames, as in Rudd Table, two long drawers under ditto, the edge of the top moulded or veneer’d crofs-way, and a firing in the upper corner, on plinth or common brackets — - - — — — 3120 EXTRAS. Each inch, more or lefs, in length - - — — Each extra long drawer - — - Each partition — — — — — — — Lining each partition crofs-way - — — — - Slipping the drawer fides, and plowing the bottoms in, each drawer — — — — — — — Each munting — — — — — — — Half ditto under the bottom — - - — — Glueing up drawer fronts, ends, or top, either folid or to veneer on, each joint — — — — — — Veneering the upper drawer fronts and edge of the glafies Veneering each long drawer front - — — — Veneering partition edges afkew or crofs-way, at per foot Ditto with king, tulip, or any other hard wood, at per foot Veneering each end — — — — — — — Each joint in the veneer of ditto, per foot in length - Veneering the top, per fquare foot — — - — Each joint in the veneer of ditto, per foot in length - — Y 2 0 I O 0 2 m 6 0 0 6 001 O03 O03 0 o if 001 Olio 008 0 o of 001 010 O O if 0 0 2 0 0 2 A firing [ 164 ] £• s ■ d • A tiring in the lower corner ot the top, per toot — — o o l Quadrant boxes to the end drawers — — — —050 For the price of infide work — See Furniture Drawer. A glafs made to Aide under the furniture drawer, with a horfe hing’d to the back, for the convenience of placing on the table — — - — “ ~ — 060 If made with a round front — - — - - 0150 Ditto ferpentine — — — — - — — 13° For the price of French feet or French brackets — See Drejfmg Chejl. Fram’d back, each pannel - - — — — 006 Munting in a plain back — — — — — — 003 Oiling and pol idling — — — - — — 016 A BASON STAND, Twelve inches fquare, a drawer in ditto fcratch beaded, two holes tor cups, and a lipping on the top — — o 4 4 EXTRAS. Each inch, more or lefs, each way — - — — Each extra cup hole — Cutting out the bafon hole _____ An aflragal on the top in place of lipping when the top is let into the rails An ovalo on the edge of the under top _ _ _ Each eitra drawer fcratch beaded _ _ _ _ o o O o o o o o o o 0 1 1 3 2 3 o Cock [ 165 ] Cock beading: each drawer — — — — Scolloping the rails, each — — — — — Aftragal round the bottom of the frame — — A ftretcher framed and fcollop’d — — — Folding tops miter dove-tail’d, or the fronts veneer’d If a fingle Hand, to be extra — — — — Oiling and polifhing - — — — — £. s. d. 003 OOl 0 0 6 OO9 O36 0 0 6 0 0 3 An INCLOS E) BASON STAND, One foot three inches fquare, framing one foot four inches deep, folding tops miter dove-tail’d, a plain door, and one drawer fcratch beaded, and a ftretcher fram’d and fcollop’d - - - - - - - - 0127 EXTRAS. Each inch, more or lefs, each way — — Ditto in depth of framing — — — — Each extra drawer fcratch beaded and flipt — An extra door fcratch beaded - — — Clamping the door, fquare clamps — - Ditto, when two, each door — - — Miter clamping ditto, each miter extra - Cock beading each drawer or door — — Glueing up the ends or back, either folid or to each joint - — — — Veneering the front long-way - - - Ditto — — 0 0 2 — — 0 0 2 - - 0 1 4 — - 0 1 0 — - 0 0 4 — - 0 0 3 - — 0 0 4 — — 0 0 3 veneer on, — — 0 0 °2 — — 0 1 O [ 1 66 ] £. s. d. Ditto trofs-way, with a joint up the middle - - -016 Veneering each extra drawer — — “ ” — 002 Veneering the tops - - - “ “ “ - 006 Veneering the fronts of ditto fet againft miter ao\ e-tailing. Ditto each end or back rail, per lquare foot 002 An aifra^al round the bottom of the framing - - - O o 6 Scolloping the rails, each — — — ~ — — OOl A reed door, with inner end, extra — - - — O 1 6 Making ditto to run both ways — — — “ — 009 An upright partition to divide the cupboard - - -006 For the price of a Night Stool or Bidet — See Shaving Stand. Oiling and polifhing - — - - - - 006 A CORNER BASON STAND, CIRCULAR FRONT, The ends one foot four inches from front to back, the legs fprung one way, with a ffretcher at bottom, one real and two fham drawers, with cock beads or firing round ditto, two holes for cups, the top rail fcollop’d, or to fham a drawer, the front veneer’d ftraight or crofs-way, wafh boards at the ends of the top, fcollop’d, and a Fmall flielf in ditto for a tumbler - - - - 0120 EXTRAS. [ i6y ] EXTRAS. Each inch, more or lefs — — — — — — o Each extra fham drawer - — - — — — o A falfe top within the wafh boards, hing’d to turn down o Making the walh boards to fold down, or to turn down when dove-tail’d together — — — — - O Making ditto to fold down with a rule joint, and fham ditto on the other fide — — — — — — o A hollow round the top — — — — — — o An extra cup hole — — — — — — - o Cutting out the bafon hole — — — — — o An aftragal on the bottom of the front rail — - — o If inclos’d between the top and bottom rails, with two doors in front, clamp’d and veneer’d, cock beaded or ftrung, or one door, with a fham on each fide — — O If ditto is made with a reed door in front — - - o Making ditto to run both ways — — - — o If a fingle one, to be extra — - — - — o Ditto, when rule joint tops - - — — — o Oiling and polifhing — — — — — — o Ditto when folding tops - - - - - - o o 0 1 3 3 o 5 i o o o 6 u . 4 . . *-« o 0 1 o o o 0 1 3 4 6 6 ' > 9 , 6 3 6 A CORNER [ i68 ] A CORNER INCLOS’D BASON STAND, as in Plate 11, Fig . 2, C • The ends one foot fix inches from front to back, folid tops to fold down with rule joint, one plain door, and a fham ditto on each fide form’d by a firing, or cock beads, three lliam drawers above ditto, veneer’d front ftraight or crofs-way, one fhelf infide, on French feet — — 1 10 o EXTRAS. Each inch, more or lefs — — - - ~ — 006 An aftragal on the bottom in front - - - -004 For the price of crofs-banding, or extra work on doors — See Tables of ditto. Oiling and polifhing - - — - — “ 0 0 9 A SHAVING STAND, One foot four inches fquare, folding tops miter dove-tail ’d, one real drawer, and one fham ditto, and a plain door in front cock beaded, two holes for cups, a glafs frame behind to rife with a rack and fpring, and fwing on center fcrews, the framing one foot fix inches deep, with ftretcher at bottom - - - - - -0190 EXTRAS. f 169 I EXTRAS £• s. d. Each inch, more or lefs, each way — - - 0 0 2 Ditto in depth of framing — — - - 0 0 2 Each extra drawer, fcratch beaded and flip ’d - — 0 1 4 An extra door, fcratch beaded - — — - — 0 1 0 Two pannels on the tides of a door to be the fame as an extra door fcratch beaded. Cock beading each drawer or door — — — - 0 0 3 Square clamping the door — — — — - 0 0 4 Ditto, when two doors, each - - - — - 0 0 3 Miter clamping ditto, each miter extra - - - 0 0 4 Veneering the front long-way — — — — — 0 I 0 Ditto crofs-way, with a joint up the middle — - — 0 1 6 Veneering the tops — — — — — - 0 0 6 Veneering the fronts of ditto fet againft miter dove-tailin l g- Ditto each end or back per fquare foot - — 0 0 2 Veneering each extra drawer front - — — - 0 0 2 A reed door, with inner end, extra - — - - 0 I 6 If made to run both ways, extra - - — - 0 0 9 An upright partition to divide the cupboard — - - 0 0 6 A hollow round the infide top — - — — — 0 1 0 Hinging the glafs frame, with a foot and rail behind — 0 1 0 Making the glafs to rife with weights - — — 0 I 6 Cafting the weights — - - — — — 0 0 6 If the legs are hollow’d out for the weights - — — 0 3 0 Each extra cup hole — — — — — — 0 0 1 Cutting the hole for the bafon - — — — - 0 0 3 z , Each [ 17° 1 Each fquare cafe for a water bottle Blocking ditto infide for an odtagon bottle ~ A round bottle cafe, with angle partition to conceal ditto - A round cafe, three inches deep, for a tumbler \ till and cover at the back of the balon, lined with foil — Hinging the tops with HL hinges — An aftragal round the bottom of the framing, at per foot - Scolloping the rails, each - A fquare bidet drawer, with a drop foot - - Ditto fram’d, with four taper legs - Filling up the drawer to receive a fweep pan - - - Shaping the upper part of the Tides to ditto Making ditto to draw out with lopers either on the fides or bottom - - ” — A night {tool in the front below the drawer, with a drop foot, or the front feet cut _ _ _ - _ A plain flap to ditto, hing’d to the back Square clamping ditto ______ Miter clamping ditto, each miter extra _ _ _ Veneering the front of a night ftool _ _ _ _ Making the above round front - - - - - Ditto, when a night ftool or bidet below the drawer — Eliptic front, extra from round front - — - - Ditto, when a night ftool or bidet below the drawer - if the legs form breaks, extra — — — — — Each extra drawer in ditto - _ — _ _ ' Veneering a round front long-way - — — - Ditto eliptic _______ Ditto crofs-way, with joint up the middle, extra - £■ s ■ d - O I O 0 0 6 O 1 3 005 OlO OlO 0 o l£ 001 040 050 OlO 006 030 046 009 006 006 004 060 076 010 0 i 6 OlO 0 2 0 01 6 0 2 0 006 Veneering [ I 7 1 J £• s • ^ Veneering the front of a night fiool in- ditto - — —006 A reed door in round front, with inner end, the fame as a l'olid door clamp’d and cock-beaded. Oiling and polifhing — — - — - — 008 A SHAVING STAND, with C anted Corners, as the Plan in Plate 11, Pig- 3, One foot eight inches at the back, one foot fix inches from back to front, framing one foot fix inches deep, one real drawer, one fham ditto, and a plain door in front, a flap top, with an aftragal on the edge of ditto, or the edge veneer’d crofs-way, and a firing in the upper corner, a glafs frame to rife with a rack and fpring, four plain Marlbro’ legs, or the cants continued down and cut to form the legs, the cants either folid or veneer’d - -140 EXTRAS. Each inch, more or lefs, each way — — — Ditto in depth of framing - — — — Two extra legs — — — — — — A tea-chefl top, extra from flap top with aftragal edge A pair of folding tops, extra from flap top, with ditto Veneering the flat top _____ Each corner firing, per foot - _ - _ z 2 002 002 030 036 060 006 001 A hollow [ 1 7 2 J f . s. d. A hollow round the infide top — - - — — 014 A ftretcher fram’d, and the edge fcollop’d — — —009 A plain fhelf in lieu of ditto when made with fix legs, the front and ends fcollop’d — — - — — O o g An aftragal round the bottom of the framing, per foot -001^ For the price of veneering and other extras — See Square Shaving Stand. Oiling and polifhing - — - - -00 10 A SHAVING STAND, with Hollow Corners, as the Plan in Plate 11, Fig. 3, One foot eight inches at the back, one foot fix inches from front to back, framing one foot fix inches deep, one real drawer,, one fham ditto, and a plain door in front, a flap top, with an aflragal on the edge of ditto, or the edge veneer’d crofs-way, and a firing in the upper corner, a glafs frame to rife with a rack and fpring, four plain Marlbro’ legs — — — — _ _ EXTRAS. Each inch, more or lefs, each way _ _ _ _ Ditto in depth of framing _ _ _ _ _ \ (olid tea-cheft top, extra from flap top, with aflragal edge — — — — _ _ 1 8 o 002 002 046' A pair [ >73 ] £■ A pair of folding tops ------ O Two extra legs - -- -- -- O Each corner firing, per foot — — — — — o A hollow round the infide top - — — — — o An aflragal round the bottom of the framing, per foot - o Veneering the hollow corners — — - — — o If the glafs is hing’d in tea-cheft top, with a horfe behind, deduct for the riling glafs and rack - — — o Then add for the glafs in the tea-cheft top — - - O A flay to fupport the top — — — — — O A quadrant ditto — — — — — — — Q For veneering the front, &c. — See Square Shaving Stand. Oiling and polifhing _ _ — — — — o A HALF-ROUND SHAVING STAND, Two feet three inches long, a door in the middle, one fham drawer above and one real drawer under ditto, a tea-cheft top, and a glafs frame hing’d to ditto, with a horfe be- hind, veneer’d front, plain taper legs, and an aftragal round the bottom of the framing — — — - 2 5 o m EXTRAS. Each inch, more or lefs, in length - - - —006 A flay to fupport the top - — — — — — 004 A quadrant s . d » 7 0 3 o 0 1 1 10 o h 2 6 5 0 2 6 o 4 . o 10 O IQ [ ! 74 ] A quadrant ditto — — — Making the glafs to rife behind, with a rack, to fwing on center fcrews — — — — — If made to rife with weights, extra Carting the weights ------ Veneering the top — — — — Each corner firing on ditto, per foot — — — Each fham drawer or door at the ends form’d by a firing or cock bead - — " ~ “ “ “ For the price of bottle cafes — See Square Shaving Stand. For extra work on doors or legs See Tables of ditto. Oiling and polifhing ------ £• d • O O 10 026 o i 6 006 007 o o 1 003 0010 c O-<2>-*O0O-O>'O'Oxe>K2x><2>. 3 No. I. A CYLINDER-FALL WASH-HAND TABLE, Two feet long, one foot ten inches wide, framing one foot feven inches deep, one real and two fham drawers in front, cock beaded, a cirtem infide the fall, the middle of ditto made to anfvver the fweep of the bafon, a water drawer at one end behind the front drawers, the top hing’d at the back, a moulding on the edge of ditto, and fweep part of the ends, two holes for cups infide, the fall veneer’d and fix’d to quadrant pieces hung with center hinges, an allragal below ditto and round the bottom of the framing, on plain taper legs - - - - 2 4 6 EXTRAS. [ 1 75 ] EXTRAS. £■ Each inch, more or lefs, in length or width — - — o Ditto in depth of framing — — — — — o If the top is in two pieces, and hing’d at each end — — o A quadrant to fupport the top — — — — — o A fwing glafs frame behind to rife with a rack and fpring — o Ditto with a foot and rail behind, extra — — — o Each extra cup hole — — — — — — O Each fquare cafe for a bottle not exceeding four inches deep o Each extra long drawer — — — — — — o Each fhort ditto — — — — — — — o Each partition — — o Lining ditto crofs-way, each — — — — — O If the fall isfolid, dedudt — — — — — - o Veneering the top, ends, or back, each — — — o Ditto, each long drawer front — — — — — o Ditto, each fhort ditto - — — — - — o Veneering partition edges afkew or crofs-way, at per foot o Ditto with king, tulip, or any other hard wood, at per foot o A night ftool in front below the drawer, with a drop foot, or the front legs cut to draw out — — - — o For the price of a bidet — See Shaving Stand. For extra work in fall, See. — See Cylinder-fall Writing Table. Oiling and polifhing — — — — - — o s. o o o 0 5 1 o 0 2 1 o 0 1 o o o o o 4 l d. 6 3 9 10 o 0 1 6 0 9 6 1 6 6 6 4 6 o No. II. f i7 6 3 No. IL A CYLINDER-FALL WASH-HAND TABLE, as in Plate t o, Fig. 1, £• d. Two feet long', one foot ten inches wide, three real draweirs and two (ham ditto in front, cock beaded, a water drawer at one end behind the front drawer, work infide the fall as in No. i, on common brackets - -250 EXTRAS. Each inch, more or lels, in length or width — — French feet, or folid French brackets - - - Veneering each end — - - — — — Each joint in the veneer — - — - — — A night ftool in front, with a drop foot to ditto, the fame as two drawers and partition. If made to draw out, with part of the French feet or brackets — — — — — — — — For the price of bidet — See Shaving Stand, deducting for the drawers. for the price of veneering the fronts or top, extra work infide, &c.' — See No. 1. Fram’d back, each panne! _____ Oiling and polilhing ______ 006 020 010 004 o 1 6 006 o 1 3 A POT f ! 77 ] A POT CUPBOARD, £. s. d. One foot two inches fquare, the framing twelve inches deep, a door in front, fcratch beaded, flat top, a mould- ing on the edge of ditto, or the edge veneer’d crofs-way, and a firing in the upper corner, plain Marlbro’ legs - o 5 O EXTRAS. Each inch, more or lefs, in length or width - — — 0 0 2 Ditto in depth of framing — — — — — 0 0 2 Clamping the door, fquare clamps — — - — 0 0 4 Miter clamping ditto, each miter extra — — — 0 0 4 When made without a door, dedud — — — — 0 1 0 A reed door, with inner end, extra — — — — 0 1 6 Veneering the front long- way — — — — — 0 0 8 Ditto crofs-way, with a joint up the middle - — 0 1 0 Each drawer in front — — — — — — 0 1 4 Veneering each ditto — - — — — — 0 0 2 Cock-beading drawer fronts or door, each — — — 0 0 3 If a firing round ditto, each — — — — — 0 0 3 Veneering the top — — — — — — — 0 0 4 Ditto each end or back — — — — — — 0 0 4 A rim groov’d in round the top — — — — 0 0 6 Beveling ditto — — — — — — — 0 0 2 An aftragal on the edge — — — — — — 0 0 2 If a tray top, with the front rail fcollop’d, and ] on the top of the legs, extra — — patras turn’d 0 1 0 a a Ditto [ * 7 8 J Ditto with fquare corners, and the legs reduced to the thicknefs of the rail, or open in front, and the fronts of the ends fcollop’d, extra from common tray top — Ditto, with hollow corners, and the legs reduced outlide to the thicknefs of the rail, extra from common tray top Ditto, when a fquare is continued on the top of the rails all round, extra ______ An ovalo on the inner corners of the legs all round — Scolloping the top edge of the end or back rails, each — Ditto the bottom edge, or an aftragal round the framing, each fide — — — — — — — — Each handle hole in the top or end - — — - Canting the legs, each — — — — — — If the door is made to turn down with a quadrant — — If the door is hing’d to Hide under the top — _ _ If made with a round front, extra — — — _ Ditto with reed door — — — Ditto eliptic, when a folid door - — _ _ _ Veneering the front long-way — — _ _ _ Each drawer in a round front — — — _ _ Veneering each drawer front — — — _ _ A firing in the lower corner of the top, per foot - - If the front is made ferpentine, extra from flraight Ditto, when reed doors — — Veneering the front — — — Each drawer in ditto ______ Veneering each drawer front _____ Sawing out the legs, each _____ Tapering ditto, each fide For the price of extra work in legs, Sec.— See Tables of ditto. f' • S , dr, 0 0 9 o 1 3 006 010 002 002 002 002 o I 3 006 040 026 050 010 020 003 O O I o 6 6 050 014 ° 2 3 004 000 000 A fingle to|' C l 79 ] £. s. d A {ingle one, to be extra - - - — — - 004 Oiling and polifhing — — — - - - 004 A CIRCULAR-FRONT CORNER POT CUPBOARD TO FIX AGAINST A WALL, The (ides one foot two inches from back to front, ten inches deep, with a folid door cock beaded, or a reed door, an aftragal on the front edge of the top and bot- tom — — — — — — — — 060 EXTRAS. Each inch, more or lefs - — — - — - 0 0 2 Ditto in depth — — — — - - 0 0 2 Clamping the door — — — - - - 0 0 6 Veneering the front - — — - - - 0 0 8 A joint up the middle of ditto - — - - - 0 0 4 Veneering the top — — — — - - 0 0 3 If a fingle one, to be extra — — - - - 0 0 6 Oiling and polifhing - - - - - - 0 0 3 a a 2 A NIGHT [ i8o ] A NIGHT STOOL, One foot four inches fquare, plain Marlbro’ legs, Iquare edge to the top, the bottom of the rails either fquare or fcol lop’d - - — t - — - "" “ EXTRAS. Each inch, more or lefs, in length or width — — Clamping the top, fquare clamps — — - Miter clamping ditto, each miter extra — — — Rounding the edge of the top or flicking with fafh plane Working an aftragal, or ftone moulding, on the front and ends of the top — — — — — — A hollow miter’d under the front and ends of the top to lap over the framing — An aflragal round the bottom of the framing, when flraight rails, per foot — — — — — — — Veneering the top — — — — — — — Ditto the rails, each ______ A pair of flumps and elbows to turn up with the top - Tapering legs, each fide ______ Plowing and tonguing the ends of the loofe feat - - A fingle one to be extra ______ Oiling and polifhing ______ £• s. d. 0 3 6 o o 1 o o 6 o o 6 o o 2 o o 8 o o 8 o o H o o 4 o o 3 o 5 o o 0 °T o o 3 o o 6 o o 3 No. I. [ 181 ] No. I. A NIGHT TABLE, £■ One foot eight inches long, one foot fix inches wide, one door in front fcratch beaded, a flat top with a moulding on the edge of ditto, or the edge veneer’d and a firing in the upper corner, plain Marlbro’ legs, the flool to draw out with part of the front legs — — — — o EXTRAS. Each inch, more or lefs, in length or width — — o A flap hing’d to a Aiding piece, in place of a door — o An extra door fcratch beaded - — — - - o Two pannels on the lides of a door to be the fame as an extra door fcratch beaded. Clamping each door or flap, fquare clamps — — o Miter clamping ditto, each miter extra — — — o Veneering the front long- way - — — — - o Ditto, when a reed door — — — — — — o Ditto crofs-way, with a joint up the middle, when plain door - - — - — — o Veneering the top - - — - -- -o Each joint in the veneer — — — — — — o A rim groov’d in on the top - - - — - o A reed door, with inner end to conceal ditto, extra — o. If made to run both ways, extra - — - - o s. d. 1 1 o ° 3 0 6 1 o o 3 0 4 1 o 0 8 1 6 0 6 ° 3 ° 9 1 6 °* 9 An [ 182 ] An upright partition to divide the cupboard — — When an ovalo is ituck on the infide of the framing all round, extra _______ Making the above round front, when a pair of folid doors Ditto, when a reed door — — — — — — Ditto eliptic, extra — — — — — — Veneering round front long-wap _ — — — Ditto crofs-wap, with a joint up the middle - — — Ditto long- wap, when reed doors - — — — If the front is made ferpentine, when reed doors — — Ditto, when a pair of folid doors — — — — Veneering ferpentine front long- wap — — — — Ditto crofs-wap, with a joint up the middle — — — Plowing and tonguing the ends of the loofe feat — — Square clamping ditto ______ Sawing out the legs, each _____ For the price of trap top, &c. — See Pot Cupboard. Oiling and polifhing — — — — — — £■ s. d. O o 6 o 1 0 o 6 o o 4 6 0 i 6 o i 4 o i IO o o 1 1 o 6 o o 9 0 o 2 0 o 2 6 o O 3 o O 6 o O °4 o O 6 c *S>< 0 No. II. A NIGHT TABLE, 1 wo feet long, the front to reprefent four drawers, cock beaded, the upper fronts hing’d to the top, the edge of the top moulded, on common brackets — — _ EXTRAS. [ 1 83 J EXTRAS. £. s. Each inch, more or lefs, in length — - — — o o Fixing elbows within the ends — — — — o l A pair of doors to reprefent four drawers and turn under the elbows, extra from the front lifting up with the top o 2 Square clamping the top - — — — — — 00 Ditto the flap or doors, each — — — - -00 Miter clamping ditto, each miter extra — — —00 Veneering the top - — — — — — — 00 Each joint in the veneer — -- — — — — 00 Veneering the ends, each — — — — —00 Each joint in the veneer — — — — — — 00 Veneering the infide of the ends above the feat, each -00 Veneering the front — — — — — — 02 Making the feat to draw out, the front to reprefent two drawers — — — — — — — — 02 Each drawer above the feat, extra from fliam drawer, cock beaded — — — — — — — — 01 Each extra partition — — — — — _ 0 o A pot cupboard above the feat, the door hing’d to the end to be the fame price as when the front is hing’d to the top An extra door — — - - — — — 01 Making the front to turn down, fupported by a quadrant, extra — — — - - - — — o 1 If made with round front, extra from ffraight - -05 Ditto eliptic, extra from round front - - — -02 A drawer in ditto above the feat, extra from fham drawer, cock beaded - — - - - - _ 02 Veneering the front — — _ _ _ _ 0 3 Making the front ferpentine - - - - - 011 d. 4 6 o 6 4 6 9 4 8 3 4 o 9 6 o a 6 o 3 o o Veneerino- O t >84 ] £. s. d. Veneering ditto - — " — — “ ~ 0 3 8 A drawer in ditto above the feat, extra from fliam drawer, cock beaded - — — ~ ~ — 0 3 0 For the price of French feet or brackets. See Di cjjfuig Chejl. Fram’d back, each pannel — — ~ — — o O 6 Oiling and polifhing — — — “ ” — 00G No. III. A SLIDING-FRONT NIGHT TABLE, Two feet long, two feet fix inches high, the top hing’d to the back, a moulding on the edge of ditto, the front to fham three drawers, the feat fix’d to ditto, and made to flidc with weights between double ends down to the height of a clofe-ftool feat, plain Marlbro’ legs —140 EXTRAS. Each inch, moreorlefs, in length - — — - 0 0 3 < Square clamping the top or front, each — — - 0 0 6 Miter clamping ditto, each miter extra — — - 0 0 6 A flap hing’d infide to cover the pan — — — - 0 0 9 Veneering the front - - — — — - 0 1 3 Ditto the top - - - — — — - 0 0 9 Each joint in the veneer — - — — - - 0 0 4 Veneering [ i8 5 ] Veneering the end rails, each — — - — - Each joint in the veneer of ditto — — — — Making ditto round front, extra - Veneering the front, when round - - - Making the front ferpentine ------ Veneering ditto - — — — — - — An aftragal round the bottom of a ftraight front - - Ditto, when round front - — — — — - Ditto, when ferpentine - — — - — — Sawing out legs, each ------ For the price of extra work in legs, &c. — See Tables of ditto. Oiling and polifhing — — — — - — £■ s. d. 0 0 5 O 0 3 O 3 6 O 1 6 O 5 6 O 1 9 0 0 8 0 0 10 0 1 0 0 0 0 0 0 6 CKgHO"O>O«O«^3«xS><0 BIDETS. A SOLID BIDET, drap’d to the pan inlide and outfide in two thickneffes, the lower one fram’d, the top edge rounded, and the cover rounded gradually to a thin edge, plain Marlbro’ or turn’d legs — — — —060 EXTRAS. Veneering the edge crofs-way - — - — -010 A cock bead round the bottom of the frame — — —010 Plain brackets, each - - - — - — 002 B B A SQUARE C 386 } £. s. d. A SQUARE BIDET, the in fide and upper edge of outlide fhap’d to the pan, with box top either folid or for fluffing, made to Hide down on the frame, the frame of the top lap dovetail’d or veneer’d, plain Marlbro’ legs, the framing four inches deep - - — — — 0 70 A fingle one of either of thefe, to be extra — — —006 If miter dovetail’d, extra — — — — — 006 Each fpring in the cover — - — — — — 006 An aflragal round the bottom of the frame — — —009 If the cover is hung on two pins at one end, and lock’d at the other, extra — — — — — — — OlO Making round ends to the cover and frame — —040 If ditto forms an aflragal — — - — — 060 For the price of extra work in legs — See Tables of ditto. Oiling and polifhing - - - — _ — ooq C <^kQx> < D A PORTABLE BIDET, Ehe box lap dovetail d or veneer’d, turn’d legs to fix with fcrews and plates, a flat top hing’d or to Aide, with lock on ditto, the edge of the top rounded — —070 / EXTRAS. [ 187 I EXTRAS. A hollow under the top all round - A tea-cheft top to ditto — — — A plinth or aftragal round the bottom Filling up the infide for a fweep pan - Oiling and polifhing - — — £. s. d. -008 -010 -009 - O I c -003 A MUSIC or READING STAND, as in Plate 11, Fig. 4, The top one foot eight inches long, one foot two inches wide, an aftragal on the edge of ditto, and a moulded book reft, a fram’d bottom with two crofs rails or one pannel fix’d to the pillar, a hollow on the edge of the framing, a h rfe to fupport the top, and three claws, as No. 1, Table of ditto — - - — — — 086 EXTRAS. Each inch, more or lefs, in length or width - — — O O 1 Square clamping the top — - — — — -00 6 Miter clamping ditto, each miter extra — — — o O 6 Framing the top with one pannel - — - -009 b b 2 Glueing [ 188 ] £. s. d. Glueing a moulding round ditto - - - - - 006 Veneering the top - - — - “* ” ~ ° 0 5 Candle boards to ditto, each - - - “ - 006 Making the top to rife with a fquare ftem and rack -030 Oiling and polifhing — — — — 004 TABLE DESKS. A TABLE DESK, two feet long, Hop’d from front to back, the edge of the top rounded, either folid or lip’d for cloth, no front nor bottom — — — — — O 2 O EXTRA. Each inch, more or lefs, in length - - - -001 A TABLE DESK, two feet long, with a flat top behind the Hope, a front, ends and back, lap dovetail’d, no bottom 030 EXTRAS. Each inch, more or lefs, in length — A bottom to ditto — — — — Hinging the flap and cleaning the infide A lock on ditto — — — — Covering the flap with cloth - - Clamping the flap, fquare clamps - o o li O O Q 006 006 003 00 6 Miter [ 189 ] £■ Miter clamping ditto, each miter extra - - - o Hinging the flat top, with a lock and partition in front of ditto — — — — — — — — o A falfe bottom to ditto — — — — — — O Side pieces to the flaps, fram’d into the top - - O Folding tops, hing’d and fupported by four lopers — o Making a cafe for infide work - — — — - o Each drawer in the infide — — - — — o Each letter hole — — — — — — — o Partitioning the drawer for ink, fand, and wafers — — o Making ditto to draw out at the end, extra — — — o For the price of arches or extra work infide — See Secretary Drawer. Each drawer in front, the whole length cock beaded - o Each fhort ditto — — — — — — — o A rim on the back, and ends of the flat top fix’d in a groove o Ditto, with aftragal on the edge - - — — - o Oiling and polifhing ------ o s. d. 0 6 1 3 0 4 1 o 6 o i 6 1 o ° 3 o 6 o 9 2 O i 6 0 9 1 o O 2 No. I. A COUNTING-HOUSE DESK, Three feet long, with one flap fquare clamp’d, and fide pieces to ditto fram’d into the top, the infide empty , the front, ends and backs fram’d into the legs, the back rail eight inches deep - — — - — — o cj 6 EXTRAS. [ J 90 ] EXTRAS. £. s. d. Each inch, more or lefs, in length 002 Ditto in depth of framing - - - - - 003 Tapering the legs, each fide — — — — — O o o~ Three low rails - - - — “ “ - 010 An aftragal at the bottom of the rail, funk in veneer thicknefs, per foot - - - - - “ o o i\ For any extra work — See Counting-houfe Deft, No. 2. C *0'*0‘ y © <,< 2 >f O*<2>^2>^S* < S>' iO O No. II. A COUNTING-HOUSE DESK, Three feet fix inches long, two feet fix inches wide, lap dovetail’d, with one flap fquare clamp’d, a quirk bead on the bottom, the infide empty, the frame mahogany or colour’d - - — — — — — — 0126 EXTRAS. Each inch, more or lefs, in length or width — — o O 3 Rabbiting the frame to receive the defk, and working a moulding round ditto — — - — — — 016 A plinth round the bottom of the defk, per foot, extra from quirk bead - - - - - - - o O l-j A rim on the top, with aftragal edge fix’d in a groove, per foot in length - - _ _ _ _ -003 Ditto fcrew’d on the outfide, the edge only rounded — o O 2 An extra flap, fquare clamp’d, including an inner end -—030 Miter [ 1 Miter clamping ditto, each miter extra - - — Each cafe for infide work ------- For the price of drawers, &c. infide — - See Secretary Drawer. Working an aftragal on the front and ends of the top, with one fquare, per foot — — — — — — Ditto, with two fquares -- — — — — Banifter railing tenanted on the flat part of the top, at per banifter, including the top rail — — — — If ditto are fix’d with pins prepar’d by the turner - — Ditto on the Hopes — — — — — — — Capping put on ditto, both edges rounded, per foot — Each miter or butt joint in ditto — — — — Ditto with aftragal edges and round top, either work’d out of the folid or groov’d to receive the top rail, per foot — Each miter or butt joint in ditto — — — - Each fiider in the ends of the frame, fquare clamp’d — For the price of extra work in ditto — See Drcffmg Chejl. Framing the bottom of the defk with two pannels, flufh — Each extra pannel — — — — — — — If the framing is beaded, each pannel extra - - — If made without a flap, dedud - — - — - Each drawer in the front, cock beaded, with a lock - Each crofs partition between the drawers - - - Each partition above the drawers — — — — If one end of the defk is dovetail’d on the miter to join to another defk, the extreme length to be meafur’d, and add for the miter’d end _ Each ftretcher, more than one in the frame - - Putting the frame together with bed fcrews, each fcrew £ . s , d » 006 01 6 o o ii 002 0 O 2 % 0 0 2 0 0 3 001 O O I 00 5 003 020 020 009 004 020 020 006 008 01 6 009 002 If £. s. d. [ * 9 2 3 If made without a frame, dedud for a frame to a three feet fix ddk — Every fix inches, more or lefs, in length of ditto — — Sawing out each leg or rail _ _ — — Each pedeftal for the ddk to ftand on, two feet in length, and two feet four inches from back to front, with four drawers, cock beaded, with locks, on faft plinth — Each inch, more or lefs, in length, down to one foot fix Ditto in depth down to two feet - — - — Each pedeftal, two feet in length, and two feet four inches from back to front, with a fiat pannel door, on faft Each inch, more or lefs, in length, down to one foot fix Ditto in depth down to one foot fix inches — — — For work infide ditto — See Counting- houfe Bookcafe. If no plinth, dedud, each fide — — — — — The price of the frame to be deduded as above. * Each drawer, more or lefs, cock beaded - - - Slipping the draw r er fides, and plowing the bottoms in, each drawer Each partition, more or lefs _____ Veneering each drawer front _ _ _ _ _ Ditto the ends, each ______ Each joint in the veneer - — Oiling and polifhing, at per foot in length, when on a frame _ _______ Ditto, the pedeftals, each ______ 040 003 001 o 16 o 006 006 0106 003 003 00 6 020 003 005 005 010 004 o o i\ 004 No, III. £ i93 ] No. III. A DOUBLE COUNTING-HOUSE DESK, • S • Four feet long, three feet ten inches wide, lap dovetail’d, one flap on each fide fquare clamp’d, a quirk bead on the bottom, the infide empty, the frame mahogany or colour’d, with two flretchers, put together with eight bed fcrews — — — — — — —150 EXTRAS. Each inch, more orlefs, in length or width — — — Rabbiting the frame to receive the defk, and working a moulding on ditto — — — — — — An aftragal on the front and ends of the top, with one fquare, per foot — — — — — — — Ditto with two fquares — — — — — — Each extra flap, fquare clamp’d, including an inner end - Miter clamping the flaps, each miter extra — — — Each cafe for infide work _____ For the price of drawers, &c. in ditto — See Secretary Drawer. Each Aider in the ends the width of the frame, fquare For the price of extra work in ditto — See Drejfmg Chejl. A flap at the end, one foot nine inches long, hung with rule joint, and fupported by a rule-joint bracket — Each inch more in length — — — — ‘ - o o o o o o o o 4 2 o O l| O 2 3 o 0 6 1 6 2 9 3 0 o 1 Each c c o o [ i94 1 £• Each extra rule-joint bracket — — — — — o Making an end on the Hope — — — — — o A flap to ditto, fquare clamp’d - - O For the price of extra work in the carcafe or railing on the top — See the preceding Dejk. If made without a frame, dedud; for a frame four feet long and under — — — — — O Every fix inches, more or lefs, in length - - •*> o Each pedefial for the deik to ftand on, three feet high, two feet long, and three feet ten inches deep, with four drawers in each front, or to draw out both ways, cock beaded, fail plinth or common brackets — — — i Each inch, more or lefs, in length, down to one foot fix inches — — — — — — — — o Each inch, more or lefs, in height — — — p Each inch above three feet ten in depth — — — o Each drawer, more or lefs, cock beaded — — — o Ditto, if made to draw out on each fide -r- — o Each partition — — — — — — — q Veneering the drawer fronts, each — — — — o Ditto each end, per fquare foot — — — — o Each joint in ditto — — — — — — o Veneering the plinth long-way, per foot in length - o Ditto crofs-way — — — — — — _ 0 If four pedeflals for ditto — See the Pedejlcils Jot Single Counting- Ho ufe Defk, Framing the ends or backs with one pannel, and ovalo on the framing, each _ 0 Each extra pannel - — 0 A cupboard at the end between the pedeflals, with a flat- pannel d door, the plinth return’d on the bottom — o s. d. o 8 6 o 2 6 6 o o 4 12 O ° 9 o 4 o 6 2 o 4 Q ° 5 0 5 O 2 o 4 O li o 2 2 O 1 O 5 6 A cafe C >95 ] £. s. d. A cafe for the infide of cupboard - - — —019 For the price of work infide ditto — See Counting-houfe Bookcafe. Oiling and polifhing, at per foot in length, when on a frame — — — — — — — — Q o 3 Ditto the pedeftals, each — — — — - —004 CASES OF DRAWERS TO STAND ON COUNTING-HOUSE DESKS. No. I. A CASE, twelve inches wide, eight inches high, and nine nine inches deep, miter dovetail’d at top, with two drawers in height — — — — EXTRAS. Each inch, more or lefs, in width, height, or depth Each drawer, more or lefs, including partition Ditto, if made to draw out both ways — A moulding round the bottom, per foot — Slipping each drawer bottom — — — -046 - O O I -OIO -020 - O O If -001 C C 2 No. II. [ 196 ] No. II. /” • *£• d* A CASE, three feet fix inches long, four inches high, and nine inches deep, miter dovetail’d at the top, with four drawers in length - - “ “ -076 EXTRAS. Each inch, more or lefs, in length, height, or depth — O O I For any extra work — See No. 1. FRAM’D INCLOSURES OF MAHOGANY FOR COUNTING-HOUSE DESKS, Per fquare foot 005 EXTRAS. An ovalo on one fide of the framing, each pannel — - Ditto on both fides — Bead and butt, extra from fquare framing, each pannel Bead and flufh, extra from fquare framing, each pannel A circular corner glued up, per fquare foot — — Working a bead on ditto to reprefent a bead and flufli A circular corner fram’d and the pannel bent in - 006 010 003 008 010 010 020 An [ J 97 ] £. s. d. An ovalo on one fide of ditto, each pannel — — — o l O For banifler railing on the straight part — See Counting - houfe Dejk, No. 2. The framing to be meafur’d to the bottom of the baniflers. Banifler railing on a circular corner, per banifler, including the top rail — — — — — — — 004 Capping on a circular corner, both edges rounded, per foot — — — — — — — — 002 Ditto with aflragal edges and round top, either work’d out of the folid, or groov’d to receive the top rail, per foot 010 A SQUARE WORK TABLE, Two feet three inches long, one foot four inches wide, edge of the top fquare, plain taper legs — - - o 3 o EXTRAS. Each inch, more or lefs, in length or width — — o O l\ Ditto, when a drawer — — — — — — 002 A drawer in ditto, cock beaded — - - — o 2 O An aflragal or flone moulding on the edge of the top, or the edge veneer’d crofs-way, and a firing in the upper corner, per foot — - — — — — 002 An aflragal round the frame, per foot — — — O o ly Three lower rails to ditto - — — — — 009 Glueing up the top, either folid or to veneer on, each joint - - - - - - - - 001 Veneering the top - - — — - - - 008 Each [ * 9 8 3 £• Each joint in the veneer, per foot - - *“ “ ° Veneering the long rails, each - ----- o Ditto the Ihort rails, each — "* “ “ — o Veneering the front, when a drawer — — — — O Cleaning the infide of the rails, &c. putting a bottom in, and hinging the top, with a lock — — O Rounding or canting the corners of the top - - - O Making the top oval — o Ditto ferpentine all round — — — — — o For the price of extra work — Chavibcv Table. A lingle one, to be extra — — — — — O Oiling and polilliing ------ O s. d . O 2 ° 3 O 2 0 5 2 6 o 4 o 6 ° 9 o 6 0 3 C OOOOOOOOOO 3 AN OVAL WORK TABLE, One foot nine inches long, the rail three inches deep and ve- neer’d, fquare edge to the top, plain taper legs — — o 6 6 EXTRAS. Each inch, more or lefs, in length — — — — Ditto, when a drawer Ditto in the depth of the rail, more or lefs - — - Veneering the top — — A brafs rim fcrew’d on the edge of the top — - - Veneering the edge, with a firing in the upper corner, or working aftragal on ditto — - - - - 0 0 2 003 004 008 006 010 Each C m 1 £■ Each extra corner firing, per foot — — — — o An aftragal round the bottom of the rail, when the legs are flufh — — — — — — — — O Each miter when the legs project — — — — o A drawer in ditto — — — — — — — o Each drawer more than one — — — — — o A bottom, when drawers - - - - — o A plain fhelf fweep’d, and fix’d with ftretcher plates — o A crofs ftretcher to fupport ditto, extra — — — o A rim groov’d in on ditto, each fide — — — — o Hinging the top, with a lock and a loofe bottom prepar’d for a filk bag, and cleaning the infide of the rails, &c. o Ditto, when a fix’d bottom, rabbited in — — — O When the legs are fprung one way, as a corner bafon ftand, each leg - — — - — — — o For the price of extra work in legs — See Tables of ditto. A fingle one, to be extra — — — — — o Oiling and polifhing — — — — — — o C | 0 i ©''00'0*o > ©*©«e>' | 0 , 3 A SQUARE URN STAND, To ftand on a table, a rim groov’d in or rabbited on the edge of the bottom, and rim rounded — — — o A fingle one, to be extra - — — — — o A ditto on a frame, plain taper legs, a rim groov’d in or rabbited on the top, a Aider for the tea-pot to ftand on, the edge of the top and rim rounded — — — o J ■ dm 0 1 1 o o of 2 9 2 3 o 6 o 8 o 6 ° 3 2 3 2 9 O 2 o 6 0 3 i 6 o 3 4 o EXTRAS. [ 200 ] EXTRAS. £. s. Veneering the rails — — “ “ “ — oo Ditto, when crofs-way — — — — — — oo Ditto the top — — — — . — - - oo Glueing white or black on the edge of the rim - - o o Ditto a triple firing — — - — — — oo Ditto a crofs band — — — — — — — 0 o Scolloping the edge of the rim — — — — o O Glueing black or white on the edge of a fcollop’d rim — o o Ditto a triple firing — — — — — — oo Ditto a crofs band — — — — — — — o i A black or white veneer to cover the joint of the top when rabbited on — — — — — — — oo An aflragal to cover ditto, or round the bottom of the frame — — — — — — — — oo Scolloping the edge of the rails — — — — o 0 A plain crofs flretcher — — — — — — o o Plinthing legs - - — — — — — q q ■For the price of extra work in legs — See Tables of ditto. A fingle one, to be extra - - — - - - 0 o Oiling and polifliing — - — — — — oo C-<2»0-0 *0<'0<'0'X3»<2>0 d. 4 6 3 3 5 6 6 6 8 3 6 4 6 8 6 3 AN OVAL URN STAND, V eneer d rail, a rim groov’d into the top, or flufh outfide and a veneer to cover the joint, the edge of the rim and top rounded, a flider for the tea-pot to Hand on, plain taper legs - _ - _ _ _ -076 EXTRAS. C 201 ] EXTRAS. Veneering the top — — — — — — — Glueing white or black on the edge of the rim — — A triple firing ditto - — - — — — A crofs-band ditto — — — — — — — Scolloping the edge of the rim — — — — — Glueing black or white on ditto — - — - Ditto a triple firing — — — — — — Ditto a crofs band _______ A fingle firing round the bottom of the rail when the legs are flufh — — — — — — — — A triple firing round ditto _____ Ditto, when the legs projedt, extra _ — — — Scolloping the bottom edge of the rail _ _ _ A corner firing round the rail, when fcollop’d — — A plain riling ftretcher ______ If the fweep is broke with a fquare, round, or hollow, each break _______ Glueing up a ftretcher in three thickneftes _ — _ For the price of extra work in legs, See. — See Tables of ditto , and Table of Stringing. A fingle one, to be extra - — - — - — Oiling and polifhing ______ £■ s. d. O o 3 O o 5 o o 7 o o 9 o o 6 o 0 7 o o 9 Q I o 0 o 4 0 o 6 o o 3 o o 6 o 1 o o 1 3 0 o 2 o o 6 o o 6 o 0 3 A SERPENTINE URN STAND, Pla in taper legs, a flider for the tea-pot to Hand on, a rim groov’d into the top, the edge of the top and rim rounded o 10 6 d d EXTRAS, [ 202 ] EXTRAS. £■ Veneering the rails — — O Ditto the top — — — — — — — O A black or white veneer on the edge of the rim — — o A triple firing ditto _ _ — _ — — o A crofs band dttto — — — — — — — o Scolloping the rim — — — — - — — o A black or white veneer on the edge of a fcollop’d rim — o A triple firing ditto — — — — — — o A crofs band ditto — — — — — — — o A (ingle firing round the bottom of the rails - - o Triple llring round ditto — — — — — — o Scolloping the rails — — — — — — o A corner firing round the rails when fcollop’d — - o For the price of a flretcher — See Oval Urn Stand. For the price of extra work in legs — See Tables of Ditto. A fingle one, to be extra — — — — — — o Oiling and polifhing — — — — — — o s. d. l o O 3 o 6 0 9 1 o o 8 0 9 1 o i 3 ° 9 1 o 0 6 1 4 o 6 ° 3 CO>*0^0<0<3* > ‘><2>''0' , 0-0 No. I. A SQUARE CELLERET, Ten inches fquare, common dovetail’d a flat top rounded, locked and hinged, the bottom to projedt, and rounded 036 EXTRAS. [ 203 ] EXTRAS. Each inch, more or lefs, in length or width — — For lap dovetailing and rounding corners, or a fafh plaine on ditto — — — — — — — — Miter dovetailing, extra from lap dovetailing - - Each bottle-hole, the partitions, eight inches deep, groov’d in Lining each hole with baize - - — — - If mahogany partitions, eight inches deep, each hole — A tea-cheft top, lip’d ______ Glueing up the fides or top, each joint — — _ Veneering ditto, each ______ Each comer firing on ditto, per foot — — - - A plinth to ditto — — — — — — — Brackets formed out of the plinth, extra _ — _ A frame for the cafe to ftand on, rabbited, and a moulding ftuck on the edge, one foot two inches high, with taper Veneering the rails ______ An aftragal round the bottom of the frame - - - Sawing out the legs, each _____ For the price of extra work in legs. See. — See Tables of ditto . A fingle one, to be extra _ — _ _ _ Oiling and polifhing ______ £. s. d. 0 0 2 0 0 8 0 0 6 00 3 0 0 3 00 4 OlO 0 o 04- 003 001 008 010 040 004 008 o o 04- 006 003 D D 2 No. II. [ 204 3 No. II. A CELLERET. £• Eleven inches fquare, partitioned for four bottles, a flat top, a lipping to cover the lead and the top of the frame, the Tides fram’d into Marlbro’ legs, champher’d inflde the whole length, and an aflragal round the bottom of the framing — ~ — — — — — O EXTRAS. Each inch, moreorlefs, each way — — - — o Each extra bottle hole, prepar’d for lead — — — o Lining each hole with baize — — — — — o If mahogany partitions, eight inches deep, groov’d in, each hole extra — — — — — — — — o Every two inches extra depth of the partitions — — o A tea-cheft top — — — — — — — o Glueing up the fides or top, each joint — — — o Veneering each fide or top Each corner firing, per foot A fingle one, to be extra — Oiling and polifhing - s . d. 6 6 O 2 O 2 ° 3 O 2 0 o£ 1 - 6 o o 6 o 1 o 6 ° 3 A HEXAGON [ 20 5 ] A HEXAGON CELLERET, To hold feven bottles, a lipping on the edge of each part where cut open, and a lining to cover the lead, the top rabbited in and an ovalo fluck on the corner, the hand made of an inch board with a moulding on the edge of ditto, plain taper legs block’d to the ftand, flips miter’d £ . s* d* round ditto to receive the bottom of the celleret — o 10 6 EXTRAS. Glueing up each fide, at per joint - — — — o 0 ok Ditto the top — — — — — — — o 0 1 If the carcafe is dovetail key’d — — — — — o 1 6 Ploughing and tonguing the joints — — — — o 1 0 If made with three hoops and not tongued — — — o 3 0 Ditto, when veneer’d — — — — — — o 4 0 Veneering each fide - - — — — — o 0 4 Ditto when the veneer is miter’d - — — — o 0 5 Veneering the top, each fide — — — — — o 0 6 Each joint in the veneer — — — - — — o 0 3 Mitering the veneer of top in fix pieces — — — o 1 6 A fingle firing between the joints, each — — — 0 0 oi A corner firing round the top, per foot — — — o 0 1 Ditto down the angles, per foot — — — o 0 1 A cock bead round the top, extra from lipping — — o 0 3 Veneering the rim of the top infide — — — — o 0 6 Each plain bracket in the angle of the legs - — - A frame lap’d together of inch and a half fluff, extra from 0 0 'k a folid board, with moulded edge — — — 004 Glueing [ 20 6 ] £. 5 . Glueing on half-inch mahogany on the edge of the frame o o Working moulding on ditto — — — — — o O Veneering the edge of the frame — — — — o o An afiragal on the bottom edge of ditto - - - o o Sawing out each leg — — — — — — oo For the price of extra work in legs — See Tables of ditto. If the tops are not lip’d, dedud: — — — — o o A fingle one, to be extra — — — — — — o o Oiling and polifhing — - — — - - o O In making the above, the workman is to do every part ex- cept foldering, lacquering, and lining with lead. d. 8 6 6 9 6 6 4 AN OCTAGON CELLERET, To hold nine bottles — [Other particulars as defcribed in Hexagon Celleret) - - - - - 0146 EXTRAS. If with three hoops and not tongued - — Ditto, when veneer’d - — — — If the carcafe is dovetail key’d - — Veneering the top with eight pieces - - A fingle firing between the joints, each - A corner firing round the top, per foot - A cock bead round the top, extra from lipping Veneering the rim of the top infide - - 040 050 020 020 0 o o\ 001 004 008 A frame [ 20 7 ] £. s. d. A frame lap’d together of inch and a half fluff, extra from a folid board with moulded edge — — — - 0 0 6 Glueing half-inch mahogany round ditto — — - 0 0 10 Working moulding on ditto - - — - - 0 0 8 Veneering the edge of the frame — - — - 0 0 8 Aftragal round the bottom edge — - - - 0 1 0 For the price of extra work — See Hexagon A fingle one, to be extra — — — Celleret. - 0 0 6 Oiling and polifhing - — — — — - 0 0 5 AN OBLONG OCTAGON CELLERET, To hold twelve bottles, [The rejt of the preamble as in Hexagon Celleret) - - - - - — o 16 6 EXTRAS. If the cants are unequal and different bevels, extra — o l o When made with three hoops — — — — — 046 Ditto, when veneer’d — — — — — — 056 Dovetail-keying the carcafe together — — — —020 Veneering the carcafe - — - - - —030 Ditto the top, each fide — — - — — — 008 Veneering the rim of the top infide - — - -009 If the top is made to project, and a moulding on the edge of ditto, extra from rabbited in - — — _ 0 i6 For the price of extra work — See Hexagon or OSlagon Celleret. A fingle r 208 j £. s. d. A fingle one, to be extra — — — — “■ O O 6 Oiling and polifhing — - ~ ~ — — 006 C >0*0 *0"0 ,( ©®©»©' •OOx'O' a No. I. AN OVAL CELLERET, Two feet long, one foot fix inches wide, the flaves glu’d up, the bottom groov’d in, the top dowel’d on and a moulding on the edge of ditto, or rabbited in and an ovalo fluck on the corner, a fcratch bead on the top where it opens, the {land made of inch fluff, a quarter- round on the corner of ditto, and a rim to receive the celleret, plain taper legs block’d behind to the fland —120 EXTRAS. Each inch, more or lefs, in length or width - Ditto, when veneer’d _____ Ploughing and tonguing the flaves together, each have Each flip glued in the edge where cut open — If made with three hoops — _ _ _ Ditto, when veneer’d — _ — _ _ Veneering the carcafe _ _ _ _ _ Ditto the top ______ Each joint in the veneer of the top _ _ _ Each corner firing on the top, per foot - _ Veneering the rim of the top infide _ _ _ -003 -004 -002 - o o 10 -030 -046 -060 -008 - o o 4 -001 -010 Veneering [ 209 ] Veneering the infide of the carcafe the depth of the lock, to cover the edge of the lead — — — — Lipping on each part where cut open — — — — A cock bead on the edge of the top, extra — — — A frame glued up in three thicknefles, veneer’d and rabbited to receive the celleret, a quarter- round on the edge of ditto, and a cock bead round the bottom of the frame, extra — — — — — — — — When the frame is made for the carcafe to flip within, and the legs cut down, and a crofs ftretcher dovetail’d on to ditto for the carcafe to reft even with the bottom of the frame — — — — — — — — If the frame is made to ftand bevelling — — — An aftragal round the frame, extra from a cock bead — An inch-and-quarter bottom rabbited and fcrew’d into the carcafe, the feet fram’d into ditto and block’d behind, and an aftragal round the bottom, conlidered the fame as a common ftand in the preamble. When folid pilafters to break the joints in the veneering, the fame as when veneer’d all round. Breaking the aftragal round pilafters, each miter extra — Sawing out legs, each — — For the price of fluting — See Table A Angle one, to be extra — — Oiling and polifhing — — £■ s- d - o i 6 O I o 003 040 040 010 006 o o of o o of O I o 006 No. II. E E [ 210 ] No. II. AN OVAL CELLERET, £- s - d. Two feet long, one foot fix inches wide, glued up in thickneffes and fram’d into the legs, the outfide veneer’d, and an aftragal round the bottom, a lipping on the top and bottom where cut open, the rim of the top infide EXTRAS. Each inch, more or lefs, in length or width If made to hand bevelling — — For other extras — See Oval Celleret , No. 1. Sawing out each leg - — — Oiling and polifhing — — — 003 060 O o o£ 00 6 AN OVAL CISTERN, ■ wo Let long, one toot fix inches wide, eight inches deep, the haves glued up, the bottom plow’d in, a rabbit in the infide to receive the lead, the top edge rounded, a hand to ditto as in Oval Celleret - - _ _ 0 10 6 EXTRAS. C 211 ] EXTRAS. £- Each inch, more or lefs, in length or width - - - o Ditto in depth — — — — — ~ - O If hoops on ditto, each — — — - — — o An aftragal on the top edge — - — - — o Staple handles fix’d on the top edge - - — — o Cleaning up the infide, extra from rabbiting for the lead o For other extras — See Oval Celleret. A fingle one, to be extra - — — — — - o Oiling and polifhing — — — — — — Q C •0«0 > 0*0'K2>«2x>0» , '0 < xS>"0 , 0 - *0 , ’0"0' , <2>' 0 A CHAMBER HORSE, With three heights of fprings, fram’d top to project over lower rails, the edge rounded, and a moulding round ditto to receive the horfe — - — - — 0106 EXTRAS. [ 21 6 ] EXTRAS. Each extra height of fprings — — — — — If frames in place of boards, each frame extra - - A Aiding foot board, with a foot to fupport ditto, and a bracket on each Ade — — — — — — Turning the fprings, each — - — — — If made with a high back, a Araight top to ditto — — If the front legs continue to the height of the back, and a rail on each Ade fram’d into ditto — — — — Sawing out the legs and elbows, each — — — Veneering the low rails — — — — — — If no moulding round the bottom of the horfe, dedudt — Oiling and poliAiing ______ Ditto, when a back ______ £. s. d. o 1 o o o 6 030 002 040 016 O O I O I o 010 004 006 CO0'0“0'0 , 0' | © i €i < ©' l <2>'D A CHAMBER CLOTHES HORSE, Three feet fquare and under, three rails in ditto, the top edges rounded, on common ogee feet _ _ _ O 2 6 EXTRAS. Each inch, higher or wider _ — _ Each extra rail — _ _ _ _ If brackets at the bottom of the ftandards - If four claws, as No. 1, Table of ditto, extra A Angle one, to be extra — — _ _ Oiling and poliAiing - _ _ _ -001 -003 -006 -014 -004 -002 A FOLDING I [ 217 ] A FOLDING CHAMBER CLOTHES HORSE, . s • do With two leaves, three feet three inches high, and four feet wide when open, three rails in each leaf — —02 6 EXTRAS. Each extra leaf — — — - — Each inch higher or wider, per leaf — - — — Each extra rail _______ Half claws on the four ftandards, fix’d - — — If with two fwing claws to the front, and two half ditto fix’d to the back ftandards — — — — — A fingle one, to be extra — - — — — - Oiling and polifhing ______ C «Svx 2 X 3 * 0 < * < 2 >* 0 ^ 0 * < S>- >< 3 >* 0’ 3 A WINDOW BLIND, Three feet long, two feet high, canvafs nail’d in a rabbit, with beads behind - - — — _ - 026 EXTRAS. Each inch, more or lefs, in length or width — — o o Oy If no canvafs, dedud — — — — _ _ 0 o 6 A pair 0 1 4 001 003 016 020 004 003 F F [ 2l8 ] £. s. d. A pair of folding blinds, fize as above, with bolt and turnbuckle morticed in - - - — — 043 If no canvafs in ditto, dedudt — — — —008 An extra frame, canvafs’d, hing’d, and bolted — —020 Fitting in and hanging to be paid for according to time. Hanging ftiles and hinging to ditto, per pair - — 010 C 0^>vO''0*' , ' , 0«2>K3< 3 A KNIFE TRAY, Square, a partition in the middle, a hand hole in ditto, or a brafs handle let on, the edges of the fides and bot- tom rounded _______ EXTRAS. If made bevelling — — — — — — — Working an aftragal on the edge of the fides — — Scolloping ________ Each partition more than one _ _ _ _ _ Rabbiting the rim to receive the bottom — _ _ A fingle one, to be extra — — - — — _ Oiling and polifhing ______ o 2 o o o o o o o o o o o o o o o 6 2 8 6 3 4 A VOIDER OR BUTLER’S TRAY, I wo feet long, with two hand holes, the edge of the rim and bottom rounded 2 o EXTRAS. L 219 1 EXTRAS. Each inch, more or lels, in length - - - Each extra hand hole - — — - - ■ An aftragal on the edge of the rim or bottom - If made with a low front, extra — — - An aftragal on the edge of the rim, when a low front If made with a round front, extra — — - An aftragal on the edge of the rim, when a round front • Ditto when a low front If made with a ferpentine front — — — An aftragal on the edge of a ferpentine front — Ditto when a low front An aftragal on the edge of the bottom, when round front Ditto when ferpentine front — — — - Rabbiting the rim to receive the bottom of a fquare tray Ditto when round front — — — — — Ditto when ferpentine ______ Each brafs plate on the corners _ _ _ Letting in ditto, each extra — - — — Cleaning ditto level with the wood, each — — A lipping on the under fide of the bottom for cloth Lining ditto with cloth — - _ _ _ Grooving the bottom to receive the edge of the cloth A lipping of cloth on the bottom _ _ _ A fingle one, to be extra — — — — Oiling and polifhing — _ _ _ _ £■ s. d. O 0 I O 0 2 O 0 4 O 0 6 O 0 8 0 1 0 O 0 6 O 0 10 O 1 4 0 0 9 0 1 1 0 0 6 0 0 8 0 0 4 0 0 6 0 0 9 0 0 1 0 0 1 0 0 1 0 0 6 0 0 4 0 0 3 0 0 2 0 0 4 0 0 3 f f 2 A VOIDER [ 220 ] A VOIDER STAND, £■ S. d. Made as a Camp Stool, to hand two feet four inches high when open, with wire centers — - - — O EXTRAS. If made with center fcrews, the nuts let in — —003 Nailing on the web — — — — — — O o 3 A fingle one, to be extra — — - — — — 003 C *0"0®^' , 0»0“0' , 0'’0 4 © ,K S> < 3 COFFEE-ROOM TABLES, Four feet long and two feet three inches wide, fquare edge to the top, the frame mahogany or beech coloured o 5 3 EXTRAS. Each inch, more or lefs, in length or width - — - O O 1 Tapering the legs, each fide — — — — - O O 0: Three low rails — — — — — — - O 1 3 Each extra ftretcher — — — — - O 0 6 Scolloping the rails, each - — — — “ O 0 2 Rounding corners, each — — — — . Mi - O 0 1 Bevel end to frame and top — — — . - O 0 4 Ditto when low rails - - — — — - O 0 6 Screwing [ 221 ] • S . d. Screwing copper or brafs on the edges, making the fcrew holes, and brightening ditto, per foot — - — o O 2 Oiling and polifhing, per foot in length — — — O O of PEDIMENTS. A plain Tablet Pediment for a piece of work, three feet fix inches long — — — — — — o Each inch, more or lefs, in length — — — — o When return’d on the ends, with pedefials at the back corners, extra — — — — — — — o Veneering the pediment boards when return’d at the ends o Ditto the tablet — — — — — — — o Ditto the pedefhds, each fide — — — — — o Each corner firing, per foot — — — — — o For the price of crofs-banding, or other extra work — See Tables of ditto. 3 0 o of 1 o o 8 o 2 o of O I An open Pitch Pediment for a piece of work, three feet fix inches long, plain pedefial and cap — —080 Each inch, more or lefs, in length Fret or eye dentil, at per foot — Block dentil ditto - - - Veneering the pediment board — - - - -001 - - - -004 -003 - - - -004 Cutting O L *22 J Cutting out and fitting on a pair of SCROLLS — Working an ogee and hollow on ditto, the head left plain A folid pediment board, fweep’d - - - Veneering ditto long-way — — — — Glueing up ditto in three thicknefles - - - Plain pedeftal and cap - — — — — Block dentil, at per foot - - — — — Eye dentil, ditto ------ Fret dentil, ditto — C •0^'S' > <5>'0' > <2>KD"<©*0' , 0 , 0- 3 A HORSE FIRE SCREEN, Three feet high and twenty inches wide, the top miter- dovetail’d, ftraight rails, a quirk bead or quarter round on the inner edge of the framing, a ftraining frame to Aide through the top rail, with lprings or weight, with flips ferew’d on the edges after it is cover’d, and the top edge veneer’d, ogee claws dovetail’d into the ftandards 090 EXTRAS. Each inch, more or lefs, in height or width — —001 Sweeping the rails, when a bead round the frame — — 16 Ditto, when a quarter round or ovalo on the framing - o 2 O Covering the ftraining frame with tammy or filk, and pa- per under ditto, each fide — — — — - 004 If £. s. d, -020 O30 -00 9 -OO4 -O08 -OO7 -OO5 -OO6 -OO9 [ 223 ] £. s. d. If the flips are groov’d to lap over the frame, all round with a bead on the edge of ditto, when draight rails, extra 016 Ditto, when fweep’d rails, and a bead on the edge of the framing — — — — — — — —02 6 Ditto, when a quarter round on the framing — — o 3 O If made to run in T grooves, extra — — — — O 1 6 An oval Aiding frame with quirk bead in front, and drain- ing frame put in with a bead behind, extra from the dart - - - — — — — - 026 Ditto, if no top rails - — — — — — 016 A vafe Aiding frame, extra — — — — — 009 Veneering the Aiding frame long-way, the veneer to form the rabbit - - - — — - — 016 Ditto crofs-way — — — — — — — 020 For the price of crofs-banding, extra work in claws, &c. — See Tables of ditto. A Angle one, to be extra - - — — _ — o o 6 Oiling and polifhing — — — — _ -003 C >0»^>"0*Qx>O l, 0*0«0«>0' D A FOLDING FIRE SCREEN, Three feet Ax inches high, one foot eight inches wide, with two leaves, the upper pannels rabbited to receive the covering, and a bead duck on the infide of the rails and dandards - - - - _ _ -060 EXTRAS. [ 224 ] EXTRAS. Each inch, more or lefs, in width or height Ditto when Hiding pannels, or braining frames to Hide - Each Hiding pannel rahbited — — — If the pannels are made to Hide through the top rails, extra each pannel — Each braining frame put in with beads behind — — Making ditto to Hide through the top, finilh’d as the Horfe Fire Screen, the outfide framing beaded on both fides Covering ditto on both Hides — — — — — Ditto, when paper’d under the covering - — - Putting the covering on one fide with braid, each pannel If beads inbead of braid, each pannel extra — — A fingle one, to be extra ______ Oiling and polibiing ______ £• d. o o l\ 0 0 2 o i 6 o o 6 o 1 o o 1 o o o 6 o o 8 004 003 006 0 O 3 C ■0~©-k5w2>°0' > 0-0^© <, j 0 < O A SLIDING FIRE SCREEN, Four feet four inches high, one foot ten inches wide, three rails, one fab pannel, and one to Hide out at each fide in grooves, with braining frames and maho- gany Hips fcrew’d on the edges after they are cover’d, with fmall grooves in the rails to receive the bops, the uprights cut away for the pannels to Hide out, and the pieces fix’d on the edges of the pannels, the top rail fcrew’d on, or dovetail’d into the bandards, and a fmall moulding miter’d round the bottom of ditto, the claws as No. 1, Table of ditto - - - — — 0186 EXTRAS. f 225 ] EXTRAS. f . s. d. Each inch, more or lefs, in length or width - -002 Corner firings, at per foot — — — — — 001 Covering the draining frames on both fides with tammy or Rlk, and paper under ditto, each frame - — o O 10 For extra work in claws, &c . — See Tables of ditto. Oiling and polifliing — - — - — - 004 C0«&000© , '©*€>0 , 03 A POLE AND STAND FOR A FIRE SCREEN, as in Plate 10, Fig . 2. The block three Reps high, plain taper pedeRal, and fquare pole, turn’d feet — - - — — 0 3° EXTRAS. Each extra Rep - - — - — Mitering each Rep - - — — — Veneering each Rep and mitering top and edges Comer Rrings round ditto, per foot - — Each ditto on the pole, at per foot - — Each ditto groov’d in, per foot - - Therming pedeRal, extra from tapering - G G -OO6 -OO4 -OIO -OOl -OOl - O o oF -003 For For the price of pannels on therming See Table No. VIII Oiling and polifhing _ - - - - A Solid Triangular Bottom, with fquare edge, on three turn’d feet Sweeping each fide — - Veneering the edges ------ o Ditto when fweep’d _ - _ — — — o Ditto the top ------- o When the bottom is morticed together, extra - - O Each hole in ditto — — — — — — — O Plain taper feet, each _ o Therming ditto, with one fquare, each - - - o Each comer firing, per foot - - - - - o Working a hollow on the edges - - — — o A groove for lead — — — — — — o A fingle one, to be extra ------ o 1 9 o lj O 3 o 4i ° 3 o 4 O 2 ° iy ° iy O 1 o 6 0 3 0 3 A Pole Screen Stand, on three claws, the claws as No. l. Table IV. the pillar and pole turn’d — - _ Fixing a pulley in a round pole _ — _ — Making and cleaning a fquare pole, and fixing a pulley in ditto — — — — — — — — Glueing up and making a hollow pole — — — Working a hollow on the four outfides of a pole — — Cutting a flit in a pole, and cleaning ditto for a paper mount 026 001 003 004 002 002 Sawing [ 227 ] £• *• *• Sawing out claws, each - — — — - - ogi For the price of extra work in claws — See Tables oj ditto. A fingle one, to be extra — — — - — 003 Oiling and polifhing — - — — — - 002 C-0-«2>»0*cS>*0 ,, 0 i, 0* , Q , *0'D MOUNTS FOR POLE FIRE SCREENS. Making a fquare ftraining frame - - - - Each fide more than four, extra - — — — A bead miter’d round a fquare frame — — — — Ditto on each extra fide - — — - — An aftragal round a fquare frame, ftuck on both edges, miter’d and key’d — — — — — — Ditto on each extra fide ------ If groov’d to clip a fquare frame, extra — — ' — Ditto, on each extra fide — — — — — A fquare frame, with an aftragal on the front, and a bead behind to keep in the ftraining frame — - — Ditto with a crofs-band in front — - - — Each extra fide — — — — — — — An oval board for painting or papering - — - Making an oval or vafe-pattern ftraining frame, morticed together ________ If breaks in the vafe, as in Plate 10, fig. 2, extra - — Covering ditto with filk, and paper under ditto — — A bead round an oval frame - — _ - — Ditto round a vafe pattern - — _ _ _ If breaks in the vafe, extra — _ _ _ _ An oval frame, glu’d up, veneer’d crofs-way on the front, and a bead behind to keep in the ftraining frame - g g 2 009 o o 00 6 o o i£ 009 002 004 O o I o I 3 o i 6 0 0 2 ^ OO4 010 O ° 3 O 06 00 9 010 00 3 030 Ditto [ 228 ] £■ s. d. Ditto with an aftragal on the front — — — — O 3 4 A vafe-pattern ditto, extra — — — — — O 0 6 If breaks in ditto, extra for the breaks — — — O 0 9 Working an aftragal on the back edge of an oval frame, one fquare form’d by bead - — — — — O 0 8 Ditto on a vafe pattern - — - — — — O 0 10 Each corner firing round an oval frame — — — O 0 4 Ditto round a vafe pattern - - - — — O 0 2 Each break in ditto — — — — — — 0 0 1 A fingle one, to be extra — - — — — — O 0 6 C ’0«3>*0' | 0''©®0 < ■©* < S > *0' , 0• D A TRIPOD BOTTOM FOR A FACE SCREEN, With a folid fweep’d ftretcher and a turn’d top, folid fquare pole, ftandards as No. i. in Table V. — - — o 3 o For extra work in ftandards — See Tables of ditto. A ftngle one, to be extra — — — — -003 Oiling and polifhing - — — — — - 002 A TRIPOD FLOWER OR CANDLE STAND, With a turn’d top and turn’d fhelf, the ftandards as No. 1 , Table V. - -----036 EXTRAS. [ 229 ] EXTRAS. Each extra turn’d fhelf - — — — — - Each triangle ditto, the fides hollow — — — — Grooving a rim into ditto — — — — - Working a quarter- round on the edge of ditto — — Ditto, when broke round the ftandards — - — For the price of extra work in the ftandards — See Tables of ditto. A Angle one, to be extra - Oiling and polifhing - — — — jr. s. d. 004 008 O o 4 t 004 009 003 002 C >O<-O<*C>O' l O 0 O <, O K C* < S> 3 A SCREEN DRESSING-GLASS FRAME, as in Plate 10, Fig. 2. The infide of the glafs frame two feet ten inches long, one foot ten inches wide, the back fram’d with four flat pannels, the ftandards beaded and glafs made to fwing, the weights caft by the plumber, claws as No. 1, Table of ditto, with focket caftors — - — -110 EXTRAS. Each inch, more or lefs, in length or width - - -002 Veneering the ftandards, each fide - — - —004 Ditto the rails, each — ... — - — — 002 Corner firings in place of beads - - - -010 Making [ 230 ] £• Making and fixing a plain handle on the top of the glais frame — — — — — — o Each extra hole in ditto — — — — — — o A fhelf fupported with brackets - _ _ _ 0 Each pin tray — o Candle boards, each ------ o If hung with tambour - o If the glafs is made to fwing, and not to rife, deduct - o For the price of extra work in claws — See Tables of ditto . Oiling and polifhing ------ o c *2>*0 0 A BOX OR LIQUOR CASE, A Plain Box, twelve inches long, ten inches wide, and ten inches deep, common dovetail’d, with a flat top, and the edge rounded ______ o EXTRAS. Each inch, more or lefs, in length, width, or depth — If lap-dovetail’d with the corners rounded, extra — — If miter-dovetail’d, extra from common dovetailing — A hollow under the top — — — _ _ _ A tea-cheft top lipt, extra from flat top - _ - Each fquare hole form’d by partitions groov’d in for If mahogany partitions, each hole - - _ _ Glueing black or white veneer on the edges of partitions, each hole — — — — — — o o o o o o o s. d. 1 o 0 I j ° 9 1 o o 6 3 6 6 6 ° 3 3 o O 2 0 6 1 o 0 4i 1 o O 2 ° 3 O O^; Each o [ 231 ] Each cover with a round hole cut in ditto Lining each hole with baize — — A cufhion infide the top — — — Veneering each fide, end, or top - Each drawer in front, fcratch beaded Cock beading ditto — — — A lock on ditto — — — — A plinth all round, with a moulding on the edge, and cut to reprefent brackets — — — — — 010 A frame for the Box to hand on, with a moulding on the edge ; one foot two inches high, with taper’d feet and focket caAors — — — — — — — 046 Eight brafs fquares let in the edges of the tops inftead of lipping - — — — — — — — 014 Each brafs plate fcrew’d on the corners - - - o o 1 Each ditto when let in and clean’d level with the wood 002 Making each brafs corner plate — — — — -001 Making each brafs plate to go acrofs the top and turn down to the opening - — - - — — 003 Letting in ditto and cleaning level with the wood -006 Each plate down the front or back, and turn’d under the bottom, the fame price as a corner plate. A flap infide the top, fcratch beaded, with a fillet to re- ceive ditto, and turn-buckle — — — - — 00 9 Square clamping ditto - - - - — - 004 Miter clamping, each miter extra - - - -004 A Aiding end to the box, extra - - — —016 Each drawer within the Aiding end — - — -009 If a fcrew through each end of the carcafe with brafs plates for the key, and fcrews complete, the nuts let in 036 A plain £. s. d. -004 -002 -00 6 -003 -012 -003 -002 [ 232 ] A plain lift-out, the whole fize of the box, with a fillet miter’d round to fupport ditto — - For any extra work — See Povtable Writing Dejk. If a fingle one, extra — — — Oiling and polifhing - s. d. 1 3 o 6 ° 3 A KNIFE CASE. A Double or Single Ogee Knife cafe for three dozen and a half and carvers, cither folid or veneer’d, and beaded - o 7.6 EXTRAS. Every extra dozen of knives or forks — - —010 Ditto of lpoons — - - - — - — 016 If the fides are commoded and veneer’d, extra from flraight fidcs — - - — - — — — 046 Plain pilaflers, each - - - - - —00 6 Ditto with cap and bafe - — — -- — — 010 For fluting — See Tables oj ditto. If the front is aflragal in the middle, and a hollow on each fide, or fquare in the middle, with ovalo comers —026 If the fides of the front are ogee, and the middle aflragal, or hollow with two plain pilaflers — - — - o 3 O Letting in a fbell without a band in the outfide top -003 Crofs-banding ditto, with firing on each fide — —008 Banding the top with a fingle firing, the front fhap’d as the flart, flraight fides — - — - - — 020 Ditto [ 233 ] Ditto if the Tides are commoded - - Ditto if the front is ogee and aflragal - Banding the front ------ Plinthing the bottom, when flraight fides — Ditto, when aflragal or hollow front — — Ditto, when commode fides — — — - If the workman prepares a band for a plinth, extra Plain ogee brackets — - — — Ditto fining - — — — — — - Ditto fining, when a hollow front — — Finifhing a cafe and putting on the furniture A fingle one to be extra — — — — Taking out part of a rivet, and putting in ditto new Railing a cafe a fecond time to patterns — Oiling and polifliing — — — — ;:K"' '■> £. s. d. -02 6 -02 6 - O 1 o -009 -010 -010 -003 -010 -016 -02 6 -006 -010 -016 -003 -002 DISSECTION OF A CASE. Turning up a cafe as in the ftart for veneering - - - - - 016 Veneering ditto all over - - - - - - - . .016 Beading ditto all over - - - - - - . . _ - 010 Cleaning up, cutting open, and lipping the cafe, and putting on an infule lock - - - - . - - - - . . - 014 Making and piercing the rivet, bringing ditto, and filling up - -020 Making a plain bottom - - - - - - - - -002 £. o 7 6 Turning up a cafe with commode fides - - - - - - - 030 Ditto if the fides of the front are ogee, and aflragal or hollow middle -020 Every extra dozen - - - - - - - - * - 002 H H No. 1. C 234 ] No. I. A VASE KNIFE CASE, £. s. d. Solid, for three dozen of knives, forks, or fpoons, fix- teen joints in the body and the fame in the top, the top to rife with a fquare ftem and wood fprings, the bottom fquare, veneer’d and lin’d with cloth - - - 1 3 O EXTRAS. Every dozen more than three — — — 016 Putting on a lock — — — “* — ~ — 006 Veneering the body, with firings in the joints of ditto and top - - — — ” — — — 080 Ogee brackets, fining - - - - - - 016 Crofs-banding, &c. — See Table of ditto . Oiling and polifhing - - - — — — O O 6 No. II. A VASE KNIFE CASE, For four dozen and a half of knives, forks, or fpoons, the outfide of top and body canted in twelve fquares, the body veneer’d, with firings in the joints of ditto and top, the neck folid, canted in fix fquares, with an afiragal at foot of ditto, and the bottom veneer’d in fix fquares, with Ogee brackets, ftrung - - -1120 A FLUTED [ 235 I A FLUTED PLATE CARRIER, £. s. d. Twelve inches deep, and thirteen inches diameter outflde, a fmall brafs hoop at bottom, and brafs baile fcrew’d on the top, the flutes cut through from top to bottom; a fpace open for taking out the plates - - —0130 EXTRAS. A hoop on the top below the baile When made odtagon, dedudt — If a Angle one, to be extra — Oiling and polifhing — — C «q>« < 3>oO<2>i)0'‘0*0‘ d A DUMB WAITER, On three claws, as No. 1, Table of ditto, with a triangle plate at bottom, the boards finifhed by the turner —036 EXTRAS. Cleaning the top Aides of the boards, each — - -004 Sawing out the claws, each - - - — -001 Each top made to turn down with two rule joints and a piece to fupport ditto, to turn on the pillar, the top fhaped and cleaned by the workman - - -028 h h 2 Working O -006 -02 6 -010 -004 [ 236 ] £, s. d. «« ■ti- x Working aflragal with one fquare on the edge ot tops, per foot — — — — — — — — Oiling and polilhing, when two heights - — — Ditto each height above two — — — — — O o o o o o 4 1 A PILLAR-AND-CLAW PEMBROKE TABLE, Two feet fix inches long on the bed, by three feet four inches when open, the frame four inches and a half deep, with one drawer, fcratch beaded, one fly on each fide, fquare edge to the top, on three claws as No. 1, Table of ditto, with triangle plate at bottom — —0126 EXTRAS. Each inch, more or lefs, in length or width — — — Ditto in depth of framing — — — — — Each extra drawer, fcratch beaded — — — - Cock beading each ditto — — _ Sawing out each claw ______ For other extras — See Pembroke Table and Tables of ditto. Oiling and polifhing * — — - — — _ 002 003 016 003 001 009 A HARLEQUIN N|i [ 2 37 J A HARLEOUIN TABLE, *v ' as in Plate 9, Fig. 3, £. s. d. Two feet two inches long, one foot nine inches from back to front, three feet high, the framing one foot ten inches deep, folding tops and taper’d legs, a writing flap in the top fquare clamp’d and lip’d for cloth, with a horfe under ditto, the harlequin to rife with fprings, feven drawers and four letter holes infide, one drawer and one fliam ditto in front, cock beaded, a cupboard below with hollow tambour to run right and left, linings to conceal ditto, and an aftragal round the bottom of the frame — 300 EXTRAS. Each inch, more or lefs, in length or width Ditto when made without a cupboard — Ditto in depth of framing - — — Making the harlequin to rife with weights Cafting the weights — — — — Making the above round front, extra — Ditto ferpentine — Each extra drawer in a flraight front, the whole Ditto in a round front - — - - Ditto in a ferpentine — — - - Veneering flraight front — - — — Ditto each extra drawer, the whole length — Veneering round front - - — - Veneering -009 - -006 -003 - -020 - -008 -060 -090 length -023 -029 _ O 3 3. - -010 -005 - -014 [ 23B ] £• Veneering each extra. drawer, the whole length - - o Veneering ferpentine front — — — ~ — o Ditto each extra drawer, the whole length - - - o Veneering the ends or back, per Iquare loot — — o Ditto the tops - -- -- - - o Veneering the fronts of ditto, fet againft miter dove- tailing. Veneering the top of the harlequin - — - — O For the price of extra work in the harlequin — See Secre- tary Drawer. For work infide of drawer, &c. — See Furniture Drawer. If no cupboard, dedudt for depth of framing as above. Ditto for tambour front, inner ends and bottom — o A pair of door frames for wire work in place of tambour o Veneering door frames long-way — — — — o Ditto crofs-way - -- -- __ 0 Putting in lilk curtains, each door — — — — o Ditto back boards, each ----- — o Each flap in the folding tops, hing’d, and a bolt on ditto o Square clamping ditto — — — — — — o Miter clamping ditto, each miter extra - - - o A lock to ditto in place of a bolt — — — — o Sweeping the edge of naps to a round or ferpentine front, each Hap - — — — — o Oiling and poii thing ------ 0 s. d. o 7 2 O 0 10 ° ij 1 o o 4 7 0 3 o 1 6 2 O o 3 o 6 O lO o 4 o 4 O 1 jr o 2 o 9 A CANTED [ 239 ] A CANTED-CORNER WORK TABLE, £. s. d. One foot nine inches long, the rail three inches deep and veneer’d, fquare edge to the top, plain taper legs — 060 EXTRAS. Each inch, more or lefs, in length — — — Ditto when a drawer - — — — — - Ditto in depth of rails — •=* — — — — A drawer in ditto, cock beaded or ftrung — - An aftragal on the edge of the top — — — - Ditto round the bottom of the frame — — — - Each extra miter when the legs projedt - - - Hinging the top with a lock, and aloofe bottom, prepared for a filk bag, and cleaning the infide of the rails, &c. Putting in afixed bottom, and preparing ditto to receive an oval bag, extra — — — — — — — Sweeping the front and end rails faint hollow, and fhaping the top to ditto, extra from llraight — — — An aftragal on the edge of the top, when ditto — - Ditto on the bottom of the frame - — — — Four fvveep’d low rails, glued up in thicknelfes — — Sweep legs, &c . — See Lady's Oval Table , Page 198. Crofs banding — See Tables of ditto. Oiling and polifhing — — — — — — 002 003 004 023 0010 0 1 o 0001 023 010 0 2 0 O 1 4 0 12 0 2 0 OO3 No. I. L 240 I No. 1 . A MOVING LIBRARY, CHIFONIERE, OR BOOK STAND, £. s. d. Two feet fix inches long, twelve inches deep, and three feet three inches high, with two fhelves, and the back fram’d into the legs, the legs rabbited to receive wire at each end, with a moulding on the infide of ditto and rails, a fmall Hone moulding, with a frieze and an aftra- gal at foot on the top, an aftragal on the bottom of the carcafe, on plain taper flump feet, with focket caftors - o 16 o EXTRAS. Each inch, more or lefs, in height, length, or width —002 Each fhelf more or lefs, including the rails — —010 If made round-front, extra — - — — — 026 For other work — See Tables of ditto. Oiling and polifhing - - - - - - 006 No. II. C 241 ] No. ir. A MOVING LIBRARY, CHIFONIERE, BOOK STAND, as in Plate 17, Fig. 1, £• Two feet long, three feet three inches high, and twelve inches deep, the top lap-dovetail’d on with a mould- ing round ditto, or dovetail groov’d, and the upper edges of the ends and back fcollop’d, two fixed fhelves, plain back, on plain taper flump feet, with focket eaflors — — — — — — — — o EXTRAS. Each inch, more or lefs, in length, height, or width — o Miter-dovetailing the top on — — — — — o Each fhelf more or lefs than two, dovetail groov’d — o Glueing up ends, fhelves, top, or bottom, each joint — o If the ends are fcollop’d between the fhelves, each fcollop o If a rim two inches high is groov’d into the back and ends of the top, the front of ditto fcollop’d, [the rim not to be meafured in the height ) - - - - - o Working an aflragal on the edge of ditto continued down the fcollop — — — — — — — o Each plain drawer the whole length, fcratch beaded — o Each fhort drawer, fcratch beaded — - - - o Cock-beading each ditto ------ o OR s. d. 8 6 o 2 0 3 0 9 o 1 O 2 O 10 0 6 1 9 1 3 ° 3 Each 1 1 E 242 ] £. s. d. Each partition - - -- - - — — 00 6 \ flap eleven inches wide, fcratch beaded, with a lock, and hing’d to turn down, rabbited and fupported with joint flays - - — - — - — —02 6 Ditto with quadrants, the ends lin’d to receive ditto, extra — — — — — — — — Cock beading the flap — _ — Square clamping ditto ______ Miter clamping ditto, each miter extra — _ _ Lipping the inlide for cloth — — — — - Lining: ditto with cloth - — — For infide work — See Secretary Drawer. For doors — See Tables of ditto. If made to Hand on a fram’d plinth, a hollow round the top edge of ditto to receive the carcafe, to be the fame as flump feet. A loofe frame to receive the flump feet, extra from being fix’d into the bottom — — — Fram’d back, each pannel — — — _ _ If an ovalo is ftuck on the framing, to be extra each pannel - - — — Veneering the ends, each fide — — _ _ _ Ditto the top or lhelves, each fide — _ _ _ Ditto each long drawer front — — _ _ _ Ditto each fhort ditto — — — Veneering the flap outfide - _ _ _ __ Ditto the edges of ends, top, bottom, or fhelves, crofs-way, at per foot — — Ditto with king, tulip, or any other hard wood, at per foot Ditto if the ends are hollow’d out at each fhelf, each hollow - _ _ o 1 6 003 004 004 004 003 0 1 0 0 0 6 0 0 4 0 0 6 0 0 5 0 0 5 0 0 3 0 0 6 0 0 1 0 0 0 0 it Veneering [ 243 ] £. s. d. Veneering the top edges of the ends, when fcollop’d -004 Ditto the top edge of the back, when fweep’d, at per foot - - — — — - — — o O l-f Corner firings, at per foot — — — — — 001 A double fland, fronted both ways, with the back put up the middle — — - — - — - 0136 The length and height, in that cafe, to be double. All other extras as above. Oiling and polifhing, when a Angle front - — —006 Ditto, when double — — - — - — 009 No. III. A MOVING BOOK STAND, as in Plate 17, Fig. 4, One foot fix inches long, one foot two inches wide, and four feet high, a flat top with a moulding on the edge of ditto, one drawer fcratch beaded, and four fhelves fcrew’d in rabbits under the rails, plain Marlbro’ feet o 12 10 EXTRAS. Each inch, more or lefs, in length or width - - Ditto in height - — - — — - Springing the feet one way, as in Plate, each foot — Ditto both ways, each foot — - - - 1 1 2 -002 - o O ojr -002 -O06 Partitioning t 244 j Partitioning the drawer for ink, fand, and wafers Cock-beading the drawer — — — “ “ Each fit elf, more or lefs, including three rails Hinging the top with a horfe to fupport ditto, and bottom under — — — — — A moulded book reft, fix’d with pins and fockets - Lipping the top for cloth fet againft cleaning up. Lining the top with cloth _ _ _ — — Oiling and polifhing — — — — — — A ROUND MUSIC STOOL, Thirteen inches diameter, to rife with a fcrew, the top fram’d, the rail fram’d, veneer’d, and a bead under ditto, on four plain Marlbro’ legs, and a fram’d ftretcher - — — — - - - - 070 EXTRAS. Tapering the legs, each fide — — — - — ooo|- A cover over the rail, to projed and form a cock bead -009 A fingle one to be extra — — — — — — 006 If only three legs, dedud - - - - - 006 Oiling and polilhing — — — — — — 003 £. s. d. 006 003 016 o 1 9 006 003 006 A GOUT t 245 ] A GOUT STOOL, as in Plate 17, Fig. 2, f. s. d. One foot ten inches long, and one foot five inches wide, a double rife and two horfes to fupport ditto, one of the ftretchers hollow — — — — — — 0 90 EXTRAS. Hinging the Rumps above the top rail — — —003 A fingle one to be extra — — - - — 00 6 Oiling and polilhing - - - - - ^-003* A CANTERBURY FOR MUSIC BOOKS, as in Plate 17, Fig. 3, One foot fix inches long, twelve inches wide, and one foot eight inches high, three long partitions and four upright ones fram’d into ditto, the upper part of the legs rabbited out the thicknefs of the partitions, one rail acrofs the middle of each end, the legs taper’d, and focket caftors - — - - - — -012 9 EXTRAS. Each inch, more or lefs, in length or width - — o o i-§- Each extra long partition, with four uprights - -010 Each C 246 ] £. s. d. Each fhort ditto, with three uprights Each fcollop in an upright — — — Each hollow top rail — — - — Each drawer, fcratch beaded — — — An aftragal round the bottom of the frame — Oiling and polifhing — — — — C-0<>©<0^0*0<<>0<0*<2>0 AN OPEN CARCASE, Three feet fix inches long, three feet fix inches high, and one foot deep, on plinth or common brackets, with a moulding round the top, and plain back — —086 EXTRAS. Each inch, more or lefs, in length, width, or depth — o O 2 Ditto if fundry work within the carcafe — - -003 If a cornice to ditto — See Table No. 11, and dedudt for top moulding, and cleaning top - - - — O 2 O If doors — See Tables of ditto. Oiling and polifhing - - - — — —003 Ditto, if doors or drawers - - - — - 006 -009 - o o oi -003 -019 -009 — —002 A PORTABLE C 247 j A PORTABLE WRITING DESK, £. s. d. Eighteen inches long, ten inches wide, and fix inches deep, lap-dovetail’d together, the top rabbited on and the cutting-open lip’d, with a bevel drawer, partitioned for ink, fand, and wafers, and a hollow for pens —08c EXTRAS. Each inch, more or lefs, in length, width, or depth — An extra flap, when a fquare drawer - - - Square clamping each flap — — - - — Miter clamping ditto, each miter extra — - - Veneering the outfide of the carcafe — - — — Plinth round the bottom — — — — — Lipping round the bottom to receive the cloth - — Ditto the infide — — — — — — — Putting black or white beads up the corners and round the Lining the writing part of the defk with cloth — — Ditto the bottom _______ Veneering the flaps, each _ — — — - A moulded book reft fix’d with pins and fockets — - A ditto not moulded ______ Letting in a brafs prop or flay, with plate to receive ditto Wafer box to lift out ______ A cover at the end of the hollow to tilt up — - — 0 0 3 0 0 6 0 0 3 0 0 4 0 1 6 0 0 4 0 0 3 0 0 4 0 0 8 0 0 4 0 0 2 0 0 4 0 0 6 0 0 4 0 0 2 0 0 4 0 0 4 A cover C 248 ] £■ A cover on the bevel — — — — — — O Each fquare hole in a drawer or lift, formed by partitions o Glueing black, white, or any other veneer on the partition edges, each hole — - — — — — o A powder box, with a folid Aiding top - - - o If the top is glued up in three thickneffes, extra from a folid top — — — — — — — — O If the top is hung with hinges, extra from a folid Aiding A plain cover — — — — — — — o A place for a round box or tumbler - — - — o An empty lift-out, the ends fquar’d from the bottom edge o A ditto, with the fides bevel’d both ways to make it all of a depth — — — — — — — o Scolloping partitions, each — — — — — o A glafs frame, eight inches by Ax or lefs, with a ftraight band - — — — — - — — o If the band is crofs-way, extra — — — — o A firing in the corners — — — — — — o A fpring drawer, when the fpring is prepar’d - - o When a box is made for curling irons, &c., with a fpring drawer at bottom to go in at the back of ditto in place of a tin box — — — — — For brafs work — See Box. Crofs-banding and other work — See Tables of ditto. A Angle one, to be extra — — — — Oiling and poliAiing s. d. 0 3 o 2 0 0 $ 1 8 o 10 ° 3 0 3 o 4 0 9 1 o 0 1 1 o o 1 0 3 1 o 4 ° 1 o 0 3 A TEA [ 249 ] A TEA CHEST, £. s. d. Eleven inches long, five inches and a half wide by five inches and a half deep, veneer’d or lap dovetail’d, a flat top, the cutting open lip’d, beaded up the corners and round the top and bottom, the carcafe dovetail’d together 046 EXTRAS. Each inch, more or lefs, in length - - - — Wood lining — — — — — — — Each hole, with a doubter, and lin’d with tin foil - A cover, with a hole cut to receive the fugar bafon and lin’d with cloth ______ Veneering and mitering ditto — — _ _ - Blocking ditto to the circle - — - — - Making a cafe for the fugar bafon to lift out, the infide of ditto fhaped to the circle, top part veneer’d and miter’d, infide lin’d with cloth _ _ - — — Putting a firing round the circle _ — - _ Ditto in the corners or round the canifler tops — — Each canifler with a flat Aiding top, or hing’d ditto — Each ditto with an oval top, veneer on the fquare part, the top of the oval hing’d — — - - - If the veneer is miter’d on the fquare part — - - Dovetail keys, extra from common keys, or from blocking the corners of ditto Banding the top of the oval - — - _ - A corner bring round ditto — — - - - Lining the infide of the lid and putting round a bead — K K 0 0 2 006 008 006 003 003 O I o 0 0 2 0 0 2 0 2 6 O30 0 0 2 004 00 6 002 006 Letting [ 2 5 0 ] £\ s. dr t Letting an oval in the top to cover the nuts of the handle 002 Banding — See Table of ditto. If lefs than three of thefe, to be each extra - -006 Oiling and polifhing — — • — - - -002.- AN OVAL TEA CHEST, Eight inches and a half long, five inches and a half wide, and five inches and a half high, veneer’d the long-way, , a firing in the top and bottom corners, the bottom groov’d for cloth, the infide of the top and the rim of ditto ve- neer’d, a lining one inch and a half down in the bottom part, which ftands up to form a bead and fteady the top, two canifters made to the fweep in three thickneffes, the top of the canifters flat and hing’d, and the infide of ditto lin’d with tin foil — — — — — 130 EXTRAS. Each inch, more or lefs, in length — — — —006 A cover with hole cut to receive a fugar bafon, and lining ditto - - - - - - - -006 Blocking ditto to the circle - — — — — 003 Making a cafe for the fugar bafon to lift out, the infide lhap’d to the circle, the outfide to fit the fweep, top part veneer’d and miter’d — — — _ _ — 016 It the bafon is oval, the cafe to be extra — — —006 Half oval tops to the canifters, each - - -006 Banding C 251 ] £. s. d. Banding — See Table of ditto . Making cauls for the canifters to be paid for extra. If a fingle one, to be extra — — — — - oio Oiling and polifhing — — — — — —002 OPEN BOOK SHELVES, Three feet long, three feet high to the top of the upper fhelf, and nine inches deep, without back, cornice, bafe, or doors, four fhelves dovetail’d into the ends, the tops of the ends fcollop’d, and the bottom ends of ditto fquare o 4 O EXTRAS. Each inch, more or lefs, in length or height — — Ditto in depth — — — — — — — Scolloping the two bottom ends — — — - Ditto the ends between the fhelves, each fcollop — — Each extra fquare end ______ Each extra fhelf dovetail groov’d into the ends — — Ditto fquare groov’d — — — — — — Grooving the ends with fquare grooves for Hiding fhelves, each groove ______ _ A plain back _______ Framing ditto, each pannel _____ Oiling and polifhing ______ o o if 002 003 o o i£ 010 009 006 o o of 010 006 003 K K 2 BED [ 252 ] BED STEPS, Two fteps high, thirteen inches wide in front, the fteps for covering, taper’d feet — - - — — £. s. d. 030 EXTRAS. Each extra ftep — - — — — — — 016 Each inch wider, when two fteps — - — —001 Each ditto, when three fteps - - — - - o O i-| If the upper ftep is enclos’d and a door to open in front, fcratch beaded, or the top hing’d - - - —030 Clamping the top - — - — _ - 003 Ditto the door - — — - — — — 004 Miter clamping, each miter extra - - - - o O 4 Cock-beading the door — — — — — — 003 A tingle one, to be extra - — — — — 004 Oiling and polifhing — - — — — — 002 Ditto when the upper ftep is enclos’d - — -003 Ck2x^>0->0''0'^'XS>-xSx , ' , 0 < D A BED TABLE, Two feet five inches long, one foot eight inches wide, with a hollow in the middle of the front fix inches deep, a rim groov d in all round, the edge of the top rounded, two clamps under the top, and four turn’d legs to fcrew into ditto, tap’d by the turner - - - -030 EXTRAS. [ 2 5 3 } EXTRAS. A fingle one to be extra - - - - - 003 Oiling and polifhing — - - — - — 002 No. I. AN UPRIGHT DISPENSARY, Nine inches high, feven inches wide, and fix inches and a half deep, folid back, fix bottles in the top, four ditto in front, two drawers under the front bottles, with par- titions and four Aiding covers in each — — -076 EXTRAS. Each inch, more or lefs, in height, width or depth —003 A place for meafure and funnel in the top — — —016 If lefs than four, to be extra each - - - —006 Oiling and polifiiing - - - - - -003 No. II. L' 254 ] No. II. AN UPRIGHT DISPENSARY, j£* • S, Ten inches high, nine inches wide, and feven inches and a half deep, folid back, feven bottles in the top, places for a tile and feales, five bottles in front, four drawers under the front bottles, the two bottom drawers par- tition’d for a peiile and mortar, four gallipots, a mea- fure, and a funnel — - - — — — 096 EXTRAS. Each inch, more or lefs, in height, width, or depth — — 003 A door in the back part, with fix bottles, and only four in the top - - — - — — — 016 If lefs than three of thefe, to be each extra - -00 6 Oiling and polifhing - - — — - — 003 No. III. AN UPRIGHT DISPENSARY, With feven drawers, thirteen inches high, ten inches wide, eight inches deep, with a folid top and door at back and front, in the top are places for four bottles, a meafure, funnel, feales, and weights, and place lor a tile, in the front are feven drawers and places for fix bottles, the two top drawers to have four Hides in each, the middle ditto a peftle and mortar, and four gallipots in one of the bottom drawers, in the back are places for eight bottles o 15 6 EXTRAS. C 2 55 ] EXTRAS. Each inch, more or lefs, in height, width, or depth If the doors or top are fquare clamp’d, to be extra each If ditto are fram’d, extra from clamping, each - A fingle one, to be extra — — — _ Oiling and polifhing — — — — — £. s. d. -003 -004 - o o 10 -010 -003 No. I. A FOLDING-DOOR DISPENSARY, Nine inches high, eleven inches and a half wide, feven inches deep, with a Hide at back, in which are places for four bottles, in the upper part of the front are places for five ditto, twelve ditto in the doors, five drawers, the upper one fitted up for fcales and weights, the two mid- dle ditto with a Aider in each, the other two drawers to contain a mortar, pefile, and four gallipots, a moulding fcrew’d to the bottom, and four pieces as feet — — o 16 o EXTRAS. Each inch, more or lefs, in height, width, or depth If the partitions are edg’d with black — If lefs than three of thefe, to be each extra Oiling and polifhing — — - — 004 o 1 o o 1 o 003 No. II. [ 2 5 6 -I No. II. A FOLDING-DOOR DISPENSARY, £• d. Thirteen inches high, twelve inches wide, eight inches and a half deep, with a Hide at back, in which are places for four bottles, in the upper part of the front are places for five ditto, eighteen ditto in the doors, five drawers, a Hide in each of the three upper ones, the mid- dle drawer for fcales and weights, meafure and funnel, the bottom drawer for a peftle and mortar and four gal- lipots, the bottom fcrew’d on and beaded - — o 18 o EXTRAS. Each inch, more or lefs, in height, width, or depth -004 Three drawers within the back hide under the bottles —060 If bottles in the bottom drawer, each fquare hole —002 If the bottom is edg’d with black and white, or any other veneer — — — — — — — — 016 If the partitions are edg’d with black — - - -016 A fingle one, to be extra — — - - - o 1 o Oiling and polifhing - - - - - -003 No. III. [ 2 57 ] No. III. A FOLDING-DOOR DISPENSARY. V JT . s . d t All folid, twelve inches high, twelve inches wide, and twelve inches deep, lap-dovetail’d together, and the corners rounded, to fold in the middle ; in the infide front of each carcafe are places for fix bottles enclos’d by a Aider, which fiiams eight drawers; under the Aiders of each carcafe are feven drawers, with Aiders in the four upper ones of each carcafe ; two drawers in each carcafe to Aiam four, and the bottom drawer in each carcafe to fham eight ; in the right-hand bottom drawer are places for nine bottles, pefile and mortar, with a fmall drawer to pull out at the end for fcales and weights ; in the left-hand bottom drawer are places for ten bottles ; at the back of each carcafe are places for four bottles enclos’d by a Aider — - — — — - — 170 EXTRAS. Each inch, more or lefs, in height, width, or depth -004 A fingle one to be extra — — — — — — 010 Oiling and polifiiing - - - - - — 003 L L A MEDICINE [ 258 ] A MEDICINE CHEST, £. s. d. Two feet long, fifteen inches wide, and twenty inches deep, folding wings, the top to lift up; in the top of the car- cafe are places for twelve quart bottles and twenty-four pint ditto, twelve of which are feen in front by lhap’d holes; underneath ditto are nine drawers, the four top drawers have a flider in each, the bottom drawers the whole length, fitted up for fix gallipots, two fets of peftles and mortars, pallet knife, &c.; in the right wing are places for fixteen pint bottles, in the left wing places for eight quart bottles ; a flider over the bottom drawer to run in the carcafe, the flider lin’d with cloth — 115 o EXTRAS. Each inch, more or lefs, in length, width, or depth -006 A frame for ditto, with a moulding on the edge, fourteen inches high, taper feet, and focket caftors — —046 Oiling and polifhing - - — — — - 004 A LADY’S FOLDING WING BOTTLE CASE, Eight inches fquare, lap-dovetail’d together or veneer’d, fifteen bottles in the top, four of which are fixed to each wing, two drawers under ditto ; in front under the bottles are two drawers the whole length, empty, the bottom fcrew’d, and black or white plinth glued on 100 EXTRAS. C 259 ] EXTRAS. £. s. Each inch, more or lefs, in length or width - —00 Four Aides in the top drawer — — — — -02 If the bottom drawer is fitted up for a mortar and peftle, meafure, funnel, and fcales - — — — -02 If the wing drawers are partition’d off for gallipots, each hole — — — — — — — — 00 Putting firings round the corners, when veneer’d — -01 A Angle one, to be extra — — • — — —01 Oiling and polifhing — — — — — — 00 d. 6 o o lz O o 3 THE END. J ) o - O -> J o - [ - TABLE No. I BANDING. On Straight Work On Oval or Sweep’d Tops. Crofs banding on ftraight work, extra d. per loot of Banding long-way with, a fingle String on one Side, per foot Banding long-way , groov’d in without a String, per foot Ditto with a String on one Side. 1 Ditto with a String on both Sides. Banding long-way, with a fngle String on one Side, per foot Banding crofs-way , with a fingle String on one Side, per foot Banding crofs-way groov'd in 2 or 3 inches from the Edge, with a fingleString on both Sides, per foot Each Miter One inch wide ) s. d. s. d. s. d. s. d. s. d. s. d. s. d. s. d. and under . ) 0 if 0 if 0 2 O 2f 0 3 t 0 4 0 5 i 0 of From 1 inch to 1 2 inches . S 0 if 0 2 0 to O 2f 0 3i 0 4f 0 5f 0 of | From 2 inches ? to 3 inches ) 0 2 O to ■Hm 0 2f 0 3 0 4 0 4| 0 6 0 0 d. Each inch above three in width of long band of Ditto crofs band Or Each extra firing on either fide, per foot of Breaking band round pilafters or legs when they project, each break o| All fingle firings that exceed 1 -8th of an inch wide, to be confidered as long banding. Banding on the fweep’d part of fronts, extra per foot o f Long banding on ferpentine fronts, to be the fame in the fzveep'd part as crofs banding. Banding in folid work, extra per foot of Ditto in lweep of Banding oval or circular tops under 2 feet long, extra per foot if Each corner firing on ditto, per foot if TABLE No. II BANDING PANNELS, &c. Crofs Banding groov’d into Oval or Circular Pannels. Crofs Banding Hollow or Round Corners of Pannels, Drawer Fronts, &c. If long Banding, deduft per foot . . o of On Flat Work, with a fingle String on one Side, per foot Without a String. With a Single String on the Infide. With a fingle firing on both Sides. One inch wide and under. From 1 inch to 2 inches. From 2 inches to 3 inches Under 1 foot long . . s. d. 0 8 s. d. 0 8| s. d. 0 8{ Each corner, exclufive 1 of the miters . . J s. d. 0 i| s. d. 0 s. d. 0 2 From 1 foot to 1 foot | 6 inches . ... j 0 7 0 7 ? 0 7 t Each half circle, exclufive ? of the miters . , J O 2| O 2-j 0 3 From i foot 6 inches to / 2 feet J 0 6 0 6| 0 6f Each double corner, in- } eluding 1 miter . J 0 3 O 3 t 0 4 f From 2 feet to 2 feet ) 6 inches . . . . J 0 5 0 5k 0 5i On hollow or round work, extra each tingle corner 0 0} Ditto, each double corner 0 o| From 2 feet 6 inches ? to 3 feet ... ) 0 4 j 0 4 f 0 5 Above 3 feet long . . 0 4 0 4 i O 4 y When a tingle tiring on both tides, extra per foot 0 1 When groov’d into folid work, extra per foot . 0 o| On hollow 01 round work, extra per foot ..02 Each extra tiring on either tide, per foot . . 0 o| ■ . , ■ TABLE No. III. Therming Legs, as in Plate i(j. Stump Feet, Cclleret, or Biddet Legs, each . Celleret-Sideboard, Card, Pembroke, Chamber, or Work-Table Legs , each. Dining, Pier, and Side- board-Table Legs, each. Therming in the Neck, as in Plate. s. d. s. d. s. d. s. d. No. 1. . . 0 3 0 4 0 5 co 0 2. . . 0 4 0 5 0 6 Hh co O 3- • • 0 4* 0 5l 0 0 6 4. . . 0 6 0 7 0 8 00 0 5- • • 0 8 0 9 0 10 1 2 6. . . 0 7 0 8 0 9 7. . . 0 9 0 10 0 1 1 8. . . 1 2 1 3 1 4 9. . . I 1 1 2 1 3 10. . . 1 if 1 1 3i 11... 1 4 1 5 1 6 — If No. 1, 2, 3, and 4, are hollow’d at the bottom, as the curve line in No. 1, extra each leg ifd. When the legs are therm’d at the top only, the tapering to be paid for extra. PLINTHING LEGS. With mouldings as in Plate (the tapering of the leg included) when miter’d at the corners to be the fame as Therming. If not miter’d, deduct each leg 1 When different colour’d wood is glued on the plinths for mould- ings, each plinth extra o| Plinthing with a plain veneer (tapering the leg to be paid feparate) 2 Ditto miter’d at the corners 3 Each firing round the plinth of * TABLE No. IV CLAWS. Making and fixing Claws, as in Plate 15. No. 1. 3 - 3 1 Vj ■ 'S* s. d. o 9 o 10 O' s 0> .2 SCI 5 o a s. d. 1 o s. d. 1 6 1 10 Therming ditto as in Plate 1,5, or the Plinths miter’d round with Mouldings, as in ditto. s. d. No. 1 . j o 4 2. o 5 s. d. ° 5 o 6 o 6 ° 7 c 7 o 9 o 8 o 10 s. d. o 6 0 7 o 8 0 9 Moulding the Tops of Claws, as in Plate 15. No, i.| No. 2. No. 3. s. d. o ol s, d. o 1 s. d. No. 4.’ s. d. o 2 No. s. d. o 24 Working Mouldings on the Top Edge of each Claw, Hop’d at Top and Bottom. Sinking Pannels in Claws. If not Hop’d, deduct for each Hop No.i.of No. 2. o~ N0.3. j. Two Beads and a Hollow or Round. Two Beads and a double Hollow. A Toad-back Mould- ing without Beads. Ditto with Beads. Ditto with a Hollow on each Side. Working Reeds, each Reed. A Panned about i-$>th of an inch deep on the Side of a Claw. — -S « K> •*>> °0 ^ £ cots £ ^ X wM* a o 0 A Panncl about 1-8 th deep on thel opEdge of a Claw. 5 3 ^ 0 co "^2 • mM- tf K 2 S s For Fire Screens and Mufic Stands. No. 1. s. d. 0 4 s. d. 0 5 s. d. 0 6 s. d. 0 7 s. d. 0 8 s. d. 0 1 2 s. d. 0 5 s. d. 0 10 s. d. 0 3 s. d. 0 6 2. 0 5 0 6 0 7 0 8 0 9 0 if 0 5i 0 11 0 4 0 8 3 - 0 6 0 7 0 8 0 9 0 10 O 2 0 6 1 0 0 5 0 10 For Writing Screens, Screen Glajfes, and Tables, from 2 Feet 3 Inches to 3 Feet 6 Inches Diameter. No. 1. 0 5 0 6| 0 8 0 9 0 10 0 if 0 5i 0 1 1 0 3t 0 7 2. 0 6 0 l\ 0 9 0 10 0 1 1 0 2 0 6 1 0 0 41 0 9 3 - 0 7 0 8j 0 10 0 11 1 0 O to I ■Mm 0 64 1 1 0 5t 0 1 1 For Dining and Loo Tables. No. 1 . 0 6 0 8 O IO 0 11 i 0 0 2 0 6 1 0 0 4 0 8 2. 0 7 . 0 9 0 1 1 1 0 1 1 O 2f 0 64 1 2 1 1 0 5 O 30 3 - 0 8 0 10 1 0 1 1 1 2 O 2-1 ; 0 7 1 2 ! 0 6 1 0 Veneering Claws for Fire Screens or Mufic Stands. Veneering the top Edge Long or crofs-way, each Veneer in a the Sides long-way, each Side d. d. d. d. d. d. d. d. d. No. 1. 2 No. 2. 3 No. 3. 34 No. 1. i| No. 2. i| N0.3. 2 No.t. 24 M|N Cl N 6 53 No. 3. 3 Ven.enng the Sides crofs-way , each Side. . . . TABLE NorV. Making, Veneering, and Inla)ing TRIPOD STANDARDS and Inlaying CLAWS. Hd C a cu G G "2 a 5 ra T 3 G CO -a o # Oh * C H c v c c r 3 Cu H3 ’a •2utx.)g xjuxoj yovj 'pUUVJ 31/) yunox 2uix/e; 3)2uf y •2uixj$ v /noi/jim ojjtp uo )3UUVJ v vi 2uijp) puv Suiyvffl •mvjp) v fo 3pi$ ?;// uo Suuts 3/2uif fo puuvj y •puuvj ?y? punox Suixjg ?)2uf y •2uixj$ v jnoy/im, ojjip uo puuvj v ui Sutjpj puv 2uiyvyj •mvjj v Jo dSpj Joj o\p uo 2uixjg 3)2uif ft puuvj y T3 C/2 O R '»>» 03 % ^3 R R vj CO *5 -O ^ co O -a co O -O ^ co O O d O Cb o co O -a ^ CO O CO o 2 "I-* •sr g >a -5 -u. £ b ■ts 3 c ^ § s . .a 0 ^ s: Ju 53 ^ b « * '*-» I co <0 *V) Cl . R 1 £ •2uiX)§ X 3 UX 0 J l/OVJ • only punox 2uujg i)2utf y •2uix?g v jnoyjvtt 0 ])ip uo puuvj v m ftuijpj puv 2un/vy) ■pxvpuv/e/ v fo 3pi$ dipt uo 2utX]$ 3)2uiJ fo puuvj y •cjjip punox Suixjs 3)2 uj y •2uujg v jnoipim opip uo puuvj v ui 2u.i)p) puv Suvfvyq •pxvpuvjg v fo juoxj 3ip uo 2uix)g 3)2 vif fo puuvj y TJ O .cu H i-« CO nd u bo eg G ^3 •r c l O bO G > <-2 *• O « bO gj ’w .2 ^ OJ U v2 9 • o o cS JCJ o .s 'O 4-1 CD CM O CO u bO C JO r T3 5 - O' w> § bO ^ C o o ^ * 4-H ^ SI CJ c«> .6 ^ a kO rt W * 1 Quartering o | Ditto crols- > -3 ^ •O LO LO kD CO o 6 ‘ 3 P}$ y :v? Cy3 P l S 3i n uo °]/ } (T r-i £ CO O o o o o o o O i "pxvpuvjs v fo juoxjj co H|H co H|N CO m|n CO k£> 00 w nn 3 c© O T~i Cl a* =0 o _ -7/72.72 Suipinop\[ pvq-pvojj y co O O o o o o c - a a - 9 ' 3 P’S y ^ CA CTi - 'O - bO On C M iS CsS ~ H 5 ifov? uo ctioflojj v yjia i otftq ■A O o o o - - - Cl •p3vxfy uy •u *" IS o o Cl bo ’pXVpUVfg T3 ^ -In LO r— o . H v fo yioxj 3xp uo ‘punoy •■A4 S-. xo ‘moflOff v pur, sonog on j « o o o O o o O o U. Vj r-' K "5 3 11 i U rJ C/D TJ Cl co «o i> *3 y-* - Cl co £ rt .6 d geo Ph C/D 1 N. B. 1 he Articles marked thus *, are included iu the itart Price where they occur. « ■ TV T ABLE No. VII 1 MOULDING, REEDING, and VENEERING i Legs and Stump Feet. When Mouldings or Reeds are Hop’d at Top and Bottom, each Side ex- tra . . • . ~ id. Stump Feet, Ccllcret, or Bid - det Legs. Cellcret - Sideboard, Card , Pembroke , Chamber, or Work-table Legs. Dining, Pier, and Side- board-table Legs. Beading the Corners, each ") Corner ...... / d. of d. of d. of Working 2 Beads and a Hol-'j low on Marlbro’ Legs, each > Side J 1 >f 2 Ditto on taper’d Legs, each ") Side J * l «f 0 * Two Beads and 2 Hollows, or'j a Toad-back Moulding, on > Marlbro’ Legs, each Side J *f 2 2 i Ditto, on taper’d Legs, each 1 Side J 2 3 3r Reeding taper’d or turn’d Legs, "1 each Reed J Of of 1 Veneering Legs long-way, each f Side / 1 »f 2 Ditto crofs way, each Side If 2 2 f SINKING PANNELS in Pildllcrs, Legs, Stump Feet, & c. and REEDING PILASTERS or Marlbro’ Legs. 5®^ O . l! T 2 5 ? 'S s _ vj A ditto aboi Inch deep, 2 Squares 1 rs *-» *** ^ * d. d. d. A fquare Pannel not exceeding f 6 Inches long . ... j 2 4 4 A hollow or round Top or") I Bottom, extra . ... J °i An atlragal Top or Bottom of if 3 Two hollow Corners at Top or } Bottom, or a Gothic Top J of 2 4 A Diamond or Oval Pannel . if 5 8 Every 6 Inches longer . . . of 1 1 Reeding Pilafters, &c. each Reed, not exceeding one foot in length of Each extra foot in length of ditto of \ ' % y . . . . •. . TABLE No. VIII. PANNELS groov’d into Friezes, Pilafters, Legs, Stump Feet, 8tc. Forming a Pannel with a fingle String. Making and letting in a Pannel with- out a String. Forming a Pannel with a Long- Band without a String. Ditto with a String on each Side. Forming a Pannel with Crop-Band. Ditto with a String on each Side. A hexagon or o£tagon pannel, 7 4 inches long and under - j co d. 3 t An oval pannel, 4 inches long 1 and under ----- £ d. 52 d. 7i d. si d. 7i An oval or diamond pannel, 4 7 inches long and under - J 3 3 A diamond pannel, 4 inches "7 long and under - - $ 4 t 6* 5 7 A pannel, fquare or with round ) ends, 4 inches long, and under ) 2 § A fquare pannel, 4 inches long 7 and under ----- j 3 y 5i 4 6 A hollow top or bottom, extra o| A hollow or round top or bot- £ tom, extra ----- j 1 1 ns An aftragal top or bottom An aftragal top or bottom 2 2 1 2 Two hollow corners at top or ) bottom ------ j 0! Of Two hollow corners at top or 7 bottom ------ j 2 2 4 2 2 i A Gothic top with a berry 1 1 A Gothic top ----- •i a 2 ! 2 ! Every 3 inches longer when formed by a firing --------- of Ditto when a pannel without a firing - of Ditto with a firing ------ of When a pannel formed by firing is not returned at top or bottom, deduct for each end --------1 A fingle firing round a pannel, 4 inches long ar Each extra firing round ditto ----- Ditto when the pannel exceeds 4 inches long, ea Each corner firing on legs when they are not ban Ditto when banded, per foot ----- Every 3 inches longer - id. Every 2 inches longer - id. Hexagon or octagon pannels to be reckoned from the dia- mond, adding for each extra miter ------ of d under - -- -- -- -- -- -- 001 ch extra foot of firing - -- -- -- -- 00 of ded - -- -- -- -- -- -- -00 1 - •• . * TABLE No. IX. STRINGING PANNELS, Forming Pannels by Strings groov'd, in, on Doors, j Drawer Fronts, Table Rails, &c. either Straight or | Sweep ’d Work. Forming Oval or Circular Pannels by Strings groov’d in on Straight or Flat Work. All fingle Strings that ex- ceed 1 - 8th of an inch wide, to be conlidered as Long Banding. A fingle String . A double String. A triple String. When a triple String projeEls, and is rounded, extra A fingle String. A double String. A triple Strimg. When a triple String projects, and is rounded, extra Each fquare pannel that con- 1 tains 2 feet of firing and under S d. 3 d. 35 d. a\ d. 2 Pannels 1 foot long and under, 1 per foot of firing - - J d. 3 z d. 35 d. 4 t d. 2 i Each extra foot cf firing - - o| oi T °| From 1 foot to 1 foot 6 inches 3 34 4 2 Each round or canted corner, ? including the miters - - ) of of l °4 Each hollow corner - - - 1 »4 T °4 From 1 foot 6 inches to 2 feet *1 *4 3 t >4 Each half circle - - - - ‘4 2 I 1 From 2 feet to 2 feet 6 inches 2 2 5 3 Each double round corner T 2 3 From 2 feet 6 inches to 3 feet ‘4 2 2 4 *4 Each double hollow corner 0 2 t 3 i§ Each round end, 4 inches dia- i meter and under - - - J 1 T 1 Above 3 feet long - - if *4 *4 1 Each hollow end - - - ^ *4 >4 2 I 1 On Hollow or Round Work, 1 extra per foot - - - ) of 1 Of Each afiragal end - - - 2 2 i 3 if When round, hollow, or aflragal ends exceed 4 inches in dia- meter — See the price of Circular Pannels. _ _ . TABLE No. X. 1 SHAM DRAWER FRONTS with Cock Beads or String. Veneering Reeds for Tam- bour Tables. ( 1 On ftraight or fat IWork. I On hollou or round Work. ^ On Serpentine Work. Holly or Satin-wood Cock Beai/s on Ma- hogany Work extra I Ebony Cock Beads, extra from Ma- 1 hog any. Each reed veneer’d and rounded, or fuck with a hollow , per foot in length, extra from folid. One foot 6 inches long and under d. 3 d. 4 d. 5 d. d. 1 d. Long way - - i From i foot 6 inches to 2 feet 4 5 6 °r X Crofs way - - i From 2 feet to 3 feet - - - 5 6 7 1 2 King, tulip, or other hard wood, extra - 1 Three feet long and upwards V 6 7 8 1 0 Each firing per foot in length 1 Reeds veneer’d long-way, if not rounded, to be the fame as folid reeds fuck with a moulding . O PLANTING ASTRAGALS on Flufh Doors, Drawer Fronts, Ends, &c. Afragals groov'd in, extra from planting on, per foot - -- -- -- - 07 On Straight or Flat Work. On Circular or Hollow Sweeps. On Serpentine Sweeps. Each fquare pannel containing 3 feet of aftragal ? and under ----- $ d. 4 d. 5 d. 6 . Each extra foot of aftragal - - - 1 4 Each hollow or round corner, or half circle - - 1 Each ditto on fweep'd work - - - - - 1 f Each double hollow or round corner, extra - - 1 Beads groov'd in to be the fame as aftragals planted on. Each hollow or round corner in Beads - - - G Each half circle in ditto - - - - - 2 1 Each double hollow or round corner in ditto 3 Oval pann els form’d by an aftragal, in four thickneftes, groov d in, the fame price as when crols banded, with a firing on each fide. Ditto formed by a Cock bead, half the price of aftragal. Oval Panncls form’d by an aftragal planted on in quarters, two thirds the price of aftragals in four thickneftes groov’d in. • . ' . , ' Preparing, Glueing on, and working Mouldings, &c. at per Foot. FLUTING. d. 2 I co m(n co f )l£? ‘f8>7 T3 rH «!r rf* m|& X CO O 0 Cl Hr* Hh O ‘i'JPlfvjlJ ‘tfjj ‘S3Z3UJ rH h|M M|rf 03 - cn G- -4 w bjO C O 0 4 h • CO h SG u. O G 0 >> C .1 fe 4- '0 G X O G to CO • w T3 "l-. -a, .ti qj W 3 op a W .£ -5 s2 c III 5 o n3 CO O kO o o U bO .5 'S G o 2 o* H PQ G bO g » ^ __ C r U § -4 bjQ .5 # c ’C G '<5 * 33 .s U G G x tJ •D X Ih Cti S co U T> '•£ c lock’d, and bolted . . J s. d. 6 6 s. d. 4 6 s. d. 1 0 s. d. 10 0 s. d. 7 0 s. d. 1 3 s. d. 12 0 s. d. 8 0 s. d. 1 9 Each fquare foot, more or") lefs, down to 4 feet, in a > 0 6 0 4 0 0 10 0 7 O if 1 0 0 8 0 H pair of doors ... .1 EXTRAS. £. s. d. Mitering the framing in front - - - - - - - - - - 020 Each extra pannel - - - - - - - - - - - - 010 Raifrng pannels, each - - - - - - - - - - - - 006 Putting in pannels with a bead behind each - - - - - - - - 006 A neck moulding, rabbitted and miter’d round the inner edge of the framing, each pannel 010 Circular corners to ditto, the moulding turn'd, each corner - - - - - 002 Aftragals on the framing, when the pannels are rabbitted and brought flufh, each pannel 009 Circular corners to ditto, the moulding turn’d, each corner - - - - - o o if Double circular corners, extra each corner - - - - - - - - o o if Fixing Wire-work, each pannel - - - - - - - - - - 008 Nailing in Curtains, each - - - - - - - - - - - 003 For Veneering — See Table No. XIII. FLUSH DOORS glued up, with clamps plow’d on, veneer'd on the outfide, and the edges veneer'd, to be the fame as flat pannel doors folid. If the clamps of fweep’d doors are nail’d on inftead of plow’d, deduct for each clamp -004 For OVAL DOORS— See Table No. XIV. For GLAZED DOORS — See Table No. XV. Oiling and polifhing, per pair - - - - - - - - - - 006 For FILLING UP RECESSES — See Table No. XIV. c TABLE No. XIII. VENEERING DOORS. j Veneering pannels each, not exceeding two fquare feet . i ditto circular 1 ditto ferpentine - Veneering pannels each, from two feet to four feet - ditto circular ditto ferpentine - Veneering pannels each, from four feet to fix feet . ditto circular — ditto ferpentine - Veneering each fquare foot more than fix, on a pannel ... ditto circular ditto ferpentine - . _ _ Veneering door frames, long-way, each pair, containing nine fquare feet each fquare foot, more or lefs, down to four feet ... Veneering circular door frames, long-way, each pair, containing nine fquare feet each fquare foot, more or lefs, down to four feet ... Veneering ferpentine door frames, long- way, each pair, containing nine fquare feet each fquare foot, more or lefs, down to four feet ... Veneering door frames, long-way, when filled up to oval pannels, extra from fquare pannels, per pair - ..... — ditto when aftragal pannels - ..... Veneering door frames, crofs-way, extra per pair, containing nine fquare feet — — each fquare foot, more or lefs, extra from ftraight ... Veneering the edges of doors, long-way, per foot in length ... each miter in ditto - - - £. s. d , 006 008 o o 10 009 O I o o 1 3 o 1 o o 1 3 016 002 O O 2| 00 3 0 2 0 O O 1 0 2 6 O O l| O30 O O 1 j 009 005 0 1 6 001 000 000} N»|>H " - ' . . • - •/*'.): s iri u:ti TABLE No. XIV. DOORS for RECESSES, &c. continued from Table No. XII. | A pair of door frames, containing nine fquare feet, hing’d, lock’d, and bolted, without pannels or mouldings - EXTRAS. Each fquare foot, more or lefs, down to four feet in the pair - Filling up the intides, and forming Ovals Each miter in ditto extra from a butt joint Flowing and tongueing each miter - Making rabbits, and working quarter-round or hollow, infide the ovals ... If the rabbit is form’d by the moulding glued in - Filling up the infides, and forming aftragal tops ------- Making rabbits in ditto, and working mouldings ------- A pair of flat pannels to ditto, or the ovals, with beads behind - Aftragals round ditto, extra from quarter-round ------- For Veneering — See Table No. XIII, Cutting Ovals or Circles in fluth doors, bending a rabbit in ditto, and putting in a pair of flat pannels, with beads behind ------- Each firing glued againft the infide of the rabbit ------- £■ FILLING UP RECESSES. For the Doors — See Tables of ditto. If ditto are not fitted, nor the furniture put on, deduit, per pair - - - - o Each hanging, fide, or rail, with a quirck bead on the inner edge, per foot in length - o Veneering ditto, per foot - -- -- -- -- -- 0 Each miter in ditto --------- . - 0 Each framing in ditto - - ------__ 0 Fixing hanging-ftiles to Carcafes, extra per foot - -- -- -- o Linings fora recefs of Deal, glued up, coloured and polifhed, per fquare foot - - o | Each flielf, top, or bottom, not exceeding three feet fix long, and twelve inches wide, glued up, colour'd and polijh’d - -- -- -- -- o Every three inches longer or wider ---------o When a Carcaje is made for a recefs with deal ends, the joints and colouring to Jland againfl cleaning up Mahogany ends. A plain Cornice, per foot in length - -- -- -- --o Glueing on ditto, per foot - -- -- -■*----0 Each miter in ditto - -- -- -- -- -- -o For any extra work in ditto — See Table No. XI. A furbafe moulding, per foot in length - -- -- -- -o Gluing on ditto, per foot - -- -- -- -- -- o Each miter in ditto - -- -- -- -- -- -o j A folid plinth, with moulding on the edge, per foot in length - - - - o Veneering ditto long-way, per foot in length ------- o Ditto crofs-way - o Each miter in ditto - -- -- -- -- -- -o Fixing the above articles into the recefs to be paid for according to time. s. d. 3 6 o 3 2 6 o 2 0 2 3 6 2 6 1 6 2 o 2 9 2 o 5 o 0 3 1 9 o if O of o of O 2 O 1 O if o 6 o of o 4 o of ° 3 o if o of o t O 2 O if O 2 I . . If long-banding, dedu6l, per foot TABLE No. XV. Filling up the Infides of DOORS for Glazing. i Dedubl for pannels as in Table No. XII. Add for the bars as under. Each piece between two miters confidered as a bar. Each ftraight bar including the miters ------ Each angle ditto ------- Each circular ditto, not exceeding a quarter of a circle, the moulding turn’ d Working the moulding of ditto ------- Each eliptic bar, not exceeding a quarter of an oval, the moulding turn'd Each ogee bar - - - - Working the moulding of eliptic, or ogee bar - Grooving ftraight aftragals to receive the rabbits, or the mouldings and rabbits work'd out of the folid extra, per foot ------ ^Grooving fweep’d aftragals to receive the rabbits, extra per foot - Filling up the infides with crofs-band without firing, to be the fame as planting on, and working aftragals. Ditto, with crofs-band in two thicknefles, with a fingle firing on each fide glued on edge- way, extra from planting on and working aftragals, per foot, miters included, ftraight v Ditto on the fweeps - -- -- -- - Each extra firing on ditto glued on edge-way, per foot - Filling up the infides with crofs-band veneer thicknefis, with a fingle firing on each fide, extra from planting on and working aftragals, per foot, miters included, ftraight part Ditto on the fweeps - -- -- -- - -Each extra firing on ditto, per foot ------ Glueing up aftragals of different coloured wood, and working the mouldings, to be the fame as crofs-band in two thicknefles, with a firing on each fide. Filling up the infides with triple ftring veneer thicknefs, to be the fame as planting on and working aftragals Each extra ftring on ditto, per foot ------ Filling up the infides with triple ftring, the middle in two thicknefles, and the fide firings glued on edge-way, extra from planting on and working aftragals, per foot, miters included, ftraight part ------ Ditto on the fweeps - -- -- - - Each extra ftring on ditto glued on edge-way, per foot - A comer firing mfde the framing to be the fame price as a moulding. 002 o o 4| 007 O O l| 009 o 1 4 003 00 1 1 003 002 ^ 0 0 3t o o o| O O 1-f O O 2-f o o of o o of o o 1 O O o o of . . . . TABLE No. XVI. PUTTING ON BRASS WORK, See. £. s. d. Common caftors, each fet - -- -- -- -- -- -----003 Letting in the plates of ditto - -- -- -- -- -- -- -- 002 Socket caftors, when the legs are taper’d to fit in, per fet -------- o o 4 Ditto on legs or claws when thoulder’d, each caftor --------00 if When the caftor has a ftrap to ferew on the under fide of a claw, the ftrap let in, each caftor extra - -- -- -- -- -- -- -- -- 00 if Iron or brafs rollers, per pair - -- -- -- -- -- -- -- 00 2f Each brafs or iron corner plate ferew’d on - -- -- -- -- -- 001 Each ditto when let in and clean’d level with the wood - -- -- -002 Making each brafs corner plate - -- -- -- -- -- -- -001 Fixing a fpring quadrant to fupport a table top. See. - -- -- -- - o o 10 Jointed ftays, each - -- -- -- -- -- -- -- -- -004 Common ftays, with a plate on the top, each - -- -- -- -- -003 Letting in plates for rods on the top of fideboard, &c„ each plate - - - o o 1 f Letting in a triangle plate under claws, the ftraps not exceeding four inches long, extra from ferewing ditto on --------------00 if Ditto, when four claws - -- -- -- -- -- -- -- -002 Each extra inch in length when triangles - - - - - - - - - - - o o of Ditto, when four claws - - - - - - ----------00 of When done by a Man who did not make the Work. Fixing on a drawer or cupboard lock, the plate let in - -- -- -- 003 Ditto when the plate is not let in - -- -- -- -- -- -- -002 Fixing a box lock, the plate let in, with ftrap - -- -- -- -- -004 Ditto when the plate is not letin ° 3 A cheft lock, the plate let in - -- -- -- -- -- -- -- 005 A mortice ditto, or a Hoping delk lock, with the plate let in -----006 Putting on hinges, per pair - -- -- -- -- -- -- -- 003 Ditto bolts, each - -- -- -- -- -- - -- -- -- 003 Drawer handles each, the nuts let in _..---------ooi) Ditto, when the nuts are not let in - -- -- -- -- -- -- 000^ Lifting handles, each pair - -- -- -- -- -- -- -- -°°3 Socket rings, each - - - - - -- -- -- -- -- -- ~°° 2 , ------ . , ' • ■ , i f ■ ■ - . Plait 1 -0 -0 -0 -0 fs 1 Q 1 a i -0 0 1 — 0 1 SclA* J . Plate / Fcj.2. > 3 Plate J Fig 1 F W3 F £ate 3 Fey. I. . P/atr to. -r~r t r . -r-t i t- □ □□□□□ □! Jq Plate J ' 1. -Fit/. 1 ~ z m iz Top mouldings for Claws Therms for Claws £ A /*/